YewdaleDefiant C40-120 User manual

yewdale.co.uk
Part no: 2006
Manufacturing Instructions
for YewdaleDefiant® cassetted blinds
(C40-120)
Manufacturing Instructions
for YewdaleDefiant® cassetted blinds
(C40-120)

YewdaleDefiant® Manufacturing instructions Part no: 20062
Manufacturing Instructions
YewdaleDefiant®cassetted blinds (C40-120)
Safety Instructions:
1.Loops in pull cords, chains, tapes and inner cords that operate the product
can cause strangulation
2.To avoid strangulation and entanglement, keep cords out of the reach of
young children. Cords may become wrapped around a child’s neck
3.Move beds, cots and furniture away from window covering cords
4. Do not tie cords together. Make sure cords do not twist and create a loop

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 3

YewdaleDefiant® Manufacturing instructions Part no: 20064
Manufacturing Instructions
YewdaleDefiant®cassetted blinds (C40-120)
C40-120 Cassetted Blinds - Deduction Chart:
Description Chart Part No. Deduction
Headbox Cut 940120 Blind width –6mm
Headbox cover/fascia cut 940121 Blind width –6.5mm
Barrel cut 918240 Blind width –49mm
Fabric width cut N/A Blind width –49mm
Fabric drop cut N/A Blind drop +250mm
Bottom bar cut 911721 Blind width –120mm
fabric insert cut 70163 Blind width –140mm
Side channel cut 911137 / 911756 Blind drop –142mm
Bottom angle cut 70050 Blind width –0mm
Chain cut 913680S Refer to child safety guidelines
Recess to blind size - 3mm on the width and 2mm on the drop

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 5
C40-120 Cassetted Blinds:
911782
Fabric retaining pip
911737
Pair of bottom
bar end caps
911822
Tracker
bottom bar
end caps
911823
Tracker
bottom bar
911721
Bottom bar
70713
Pile seal
70713
Pile seal
940122
End plates (set)
940121
Headbox cover
933010
Safety Cover Screw
940120
Headbox fascia 120
917277W
Geared down clutch
918240 - 53mm Barrel
918247 - 70mm Barrel
940011
Transition plate (set)
70796
Zip
913680S
Metal ball chain
940005
Chain Guide
940006
Screws for
Chain Guide
933010
Screws for
End Caps
911137
Side channel 55mm face fix
911756
Side channel
55mm recess fix
70050
Recess fixing strip
940000B
Tracker Insert
940001B/W
Face/Recess
Fix Tracker
side channel
132
Grommit

YewdaleDefiant® Manufacturing instructions Part no: 20066
Manufacturing Instructions
YewdaleDefiant®cassetted blinds (C40-120)
1.Ensuring the head box/fascia profile is square within the saw, cut the head
box to size.
2.Ensuring the head box cover is square within the saw, cut the head box to
size making sure there is no distortion.
N.B It is critical that the profile is cut square to enable the cover to close.
3.Cut barrel, bottom bar, fabric and side channels to size.
4.File all aluminium cuts.
5.Attach fabric to barrel and bottom bar inserting the bottom bar end caps.
6.Attach fabric retaining pips every 400mm on both sides of the drop of the
fabric.
7.Insert the transition plates into the head box and attach the end plates
using 933010 screws.
8.Cut the chain to length and attach to control mechanism.
9.Making sure the control is on the correct size, insert the control mechanism/
pin end into the barrel and place barrel and fabric into the head box.
10.Using the punch provided, punch a hole in the head box cover to enable the
chain to enter/exit the head box by:
a) Place the template on the control side of head box cover and mark the
hole for the chain guide using a pencil (template should be pushed firmly
against the lip on the cover).
C40-120 Cassetted Blinds:
Use this
hole on the
template

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 7
b) Remove the template and drill an 8mm hole.
c) Place the punch into position and tighten the bolt, ensuring the punch is
held square at all times.
N.B It is critical that the punch is held square.
11.To drill the holes for the safety screws at either end of the head box cover,
use the template provided. Mark the hole shown below with a pencil. When
marked, remove the template and drill a 4mm hole and countersink.
12.Attach the chain guide to the transition plate by threading the chain
through the chain guide and then by using 2 chain guide screws (940006)
attach this to the transition plate.
13.Attach head box cover onto the head box, close and secure using the 2
safety screws (933010).
14.Lift head box onto text rig and ensure blind operates correctly.
15.To transport blind, it is recommended that the barrel with fabric is removed
from the head box and packaged separately.
Ensure the relevant child safety device is used to comply with BS
EN13120:2009+A1:2014, BS EN16433:2014 and BS EN16434:2014.
Use this
hole on the
template

Yewdale, Enterprise Way,
Wickford, Essex SS11 8DH
Call [phone]
Fax [phone]
Email [email protected]o.uk
Visit yewdale.co.uk
For more information on all
Yewdale products, please call
the sales department.
curtain track systems
yewdale.co.uk
see things differently
A concise approach to
a broad spectrum of
commercial curtain
track requirements with
simplistic control options
and designed for almost
every application.
®
cubicle and shower screens
yewdale.co.uk
see things differently
A dedicated range of privacy
and shower curtains with a
primary infection control
focus, providing an all-
encompassing solution to
increased levels of dignity.
®
cubicle and track systems
yewdale.co.uk
see things differently
The industry’s preferred
choice of maintenance
free privacy track systems
providing enhanced personal
welfare throughout the entire
healthcare and public sectors.
®
magnetic anti-ligature system
yewdale.co.uk
see things differently
The only fail-safe range of
exclusive anti-ligature products
designed to maximise the
safety of persons by removing
the death potential where
secure care is required.
®
fabric and blind systems
A comprehensive range
of window blind systems
designed with unique
technical features and to
the exacting specifications
that active commercial
environments demand.
yewdale.co.uk
see things differently
®