YewdaleDefiant VL31 Single Draw R/H Control User manual

yewdale.co.uk
Part no: 1001
Manufacturing Instructions
for YewdaleDefiant® Vertical blinds
(VL31 Single Draw R/H Control)
Manufacturing Instructions
for YewdaleDefiant® Vertical blinds
(VL31 Single Draw R/H Control)

YewdaleDefiant® Manufacturing instructions Part no: 10012
Manufacturing Instructions
YewdaleDefiant®Vertical blinds (VL31 Single Draw R/H Control)
Safety Instructions:
1.Loops in pull cords, chains, tapes and inner cords that operate the product
can cause strangulation
2.To avoid strangulation and entanglement, keep cords out of the reach of
young children. Cords may become wrapped around a child’s neck
3.Move beds, cots and furniture away from window covering cords
4. Do not tie cords together. Make sure cords do not twist and create a loop
Ensure the relevant child safety device is used to comply with BS
EN13120:2009+A1:2014, BS EN16433:2014 and BS EN16434:2014.

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 3
VL31 Single Draw R/H Control:
926325W
926310/14W
927015W
927007
927000
927006
927010
927004W
927015W
927002/3W
927011/12
927016W
928750/54W
928850/54W

YewdaleDefiant® Manufacturing instructions Part no: 10014
Manufacturing Instructions
YewdaleDefiant®Vertical blinds (VL31 Single Draw R/H Control)
VL31 Single Draw R/H Control:
Please note, eye, hand and ear protection must be worn whilst manufacturing
this blind.
1.Check the profile - part number 92700W, and spline - Part number 927006,
are free from damages
2.Cut profile 92700W to blind width minus 4mm
3.Cut spline 927006 to blind width minus 4mm
4.Insert spline into one end of end cap - 927015W, securing with stop ring on
the outside edge – 927010.
5.Using the chart below, insert the appropriate tubular spacers, part number
927007W onto the drive end of the spline. Should the spacers require
cutting in half, use a sharp knife.
6.Select the appropriate trucks:
• If left hand control and 127mm, use 927002L
• If right hand control and 127mm, use 927002R
• If left hand control and 89mm, use 927003L
• If right hand control and 89mm, use 927003R
VL31 89mm single draw VL31 127mm single draw
Control End Control End
1.5 2.5

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 5
7.Using the formula below calculate the correct amount of trucks.
Actual blind width ÷ actual link length
For example, for a 400mm blind:
89mm louvre (the actual link length is 79mm) 400÷79mm = 5pcs
127mm louvre (the actual link length is 115mm) 400÷115mm = 4pcs
Round the figure up to next whole number.
8.To remove any surplus trucks from the ready linked stacks, cut the metal
spacer line 5mm ahead of the leading truck.
9.Attach the wand control – 927015W, to the leading truck, see fig 1. (Truck
furthest away from the stack end) using the correct adaptor shown in fig 2
and 3.
10.Insert the screw into the 927015W
For plastic
trucks
For metal
trucks

YewdaleDefiant® Manufacturing instructions Part no: 10016
Manufacturing Instructions
YewdaleDefiant®Vertical blinds (VL31 Single Draw R/H Control)
11.Loading the trucks onto the spline, with the links facing away from the stack
position, insert a stop ring (927010), onto the spline between the first and
second truck.
12.Sliding all the trucks fully home, against the stack end of the control set,
fix the stop ring in place using a slotted screwdriver to hold the first truck
captive.
13.Slide the shaft support with magnet onto the spline (927004W)
14.Now insert the spline and trucks into the profiled channel – 92700W. Slide
the lead truck down the channel.

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 7
15.Using the workings below, insert the appropriate tubular spacer part
number 927007W onto the spline on the opposite end to the stack position.
16.Insert the second control set onto the spline and fix in place using a stop
ring (927010) and fasten with slotted screwdriver.
17.Using part number 927016W, cut the wand to the desired length and fix
onto 927015W with the screw provided. (Round o cut end of control wand
with an abrasive material).
18.Using the wand, pull trucks back and forth to make sure the trucks run
smoothly.
19.Wipe clean the profile and bring all trucks back to the control end ready for
packing.
VL30 89mm single draw VL30 127mm single draw
Control Idle Control Idle
0 1

Yewdale, Enterprise Way,
Wickford, Essex SS11 8DH
Call [phone]
Fax [phone]
Email [email protected]o.uk
Visit yewdale.co.uk
For more information on all
Yewdale products, please call
the sales department.
curtain track systems
yewdale.co.uk
see things differently
A concise approach to
a broad spectrum of
commercial curtain
track requirements with
simplistic control options
and designed for almost
every application.
®
cubicle and shower screens
yewdale.co.uk
see things differently
A dedicated range of privacy
and shower curtains with a
primary infection control
focus, providing an all-
encompassing solution to
increased levels of dignity.
®
cubicle and track systems
yewdale.co.uk
see things differently
The industry’s preferred
choice of maintenance
free privacy track systems
providing enhanced personal
welfare throughout the entire
healthcare and public sectors.
®
magnetic anti-ligature system
yewdale.co.uk
see things differently
The only fail-safe range of
exclusive anti-ligature products
designed to maximise the
safety of persons by removing
the death potential where
secure care is required.
®
fabric and blind systems
A comprehensive range
of window blind systems
designed with unique
technical features and to
the exacting specifications
that active commercial
environments demand.
yewdale.co.uk
see things differently
®