YewdaleDefiant C20s User manual

yewdale.co.uk
Part no: 2000
Fitting Instructions
for YewdaleDefiant® cassetted blinds
(C20s)
Fitting Instructions
for YewdaleDefiant® cassetted blinds
(C20s)

YewdaleDefiant® fitting instructions Part no: 20002
Fitting Instructions
YewdaleDefiant®cassetted blinds (C20s)
Safety Instructions:
1.Loops in pull cords, chains, tapes and inner cords that operate the product
can cause strangulation
2. To avoid strangulation and entanglement, keep cords out of the reach of
young children. Cords may become wrapped around a child’s neck
3.Move beds, cots and furniture away from window covering cords
4. Do not tie cords together. Make sure cords do not twist and create a loop

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 3

YewdaleDefiant® fitting instructions Part no: 20004
Cassetted Blinds:
1.Remove the two safety screws in the underside of the head box to enable the
cover to open (if sidewinder, also unscrew the chain guide).
2.Using the indents (see diagram below) within the head box, drill 3.8mm
fixing holes either in the top or back depending on whether it is required to
be face or recess fixed. Fixing holes should be equally spaced and no more
than 1m apart to ensure head box is fixed completely level.
3.Lift the head box in to place. If you are fitting it to steel or concrete, mark
where the holes need to be drilled so the hole can be plugged. Drill the
holes and lift the head box into place and fix using the appropriate screws.
If fitting it to timber, simply fix the head box in place using the appropriate
screws.
NB. To operate correctly, complete blind MUST be level.
Fitting Instructions
YewdaleDefiant®cassetted blinds (C20s)

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 5
4.Insert the barrel and fabric into the head box. If it is spring controlled, go to
point 5 - 6 and then to point 11. If the blind is side winder controlled, go to
point 7- 9 and then to point 11. If the blind is crank controlled, go to point 9
and then to point 16. If it is electrically controlled, go to point 10 and refer to
motor instructions for setting limit stops.
5.Insert/click the blind on to the back bar into the head box. The spring must
be on the right-hand side unless fabric is reverse rolled.
6.The spring would have been tensioned during the manufacturing process
but the tension can be increased or decreased if required. If the fabric does
not wind up completely when the blind is operated, greater spring tension
can be applied as follows:
a) The spring would have been tensioned during the manufacturing process
but the tension can be increased or decreased if required. If the fabric
does not wind up completely when the blind is operated, greater spring
tension can be applied as follows:
b) Remove the blind and back bar from the head box.
c) Use a flat head screwdriver through the hole in the bracket at the spring
end to either increase or decrease the tension as desired.
d) Insert/click the barrel and fabric back into the head box.
e) Attach the pull cord onto the bottom bar.
7.Fix the chain guide into position by threading the chain through the chain
guide. Ensure that the chain is not twisted.
8.Re attach the chain guide using the screws provided.
9.Insert the barrel and fabric into the head box.
10.Drill an exit hole for the electric cable and insert the fabric and barrel into
the head box, making sure the supply cable is carefully threaded through.
11.If side guiding is required, please follow the instructions overleaf. If not
required then click the cover back in place and secure using the 2 safety
screws previously removed.
12.Check the blind operates correctly.
13.Ensure the relevant child safety device is used to comply with BS
EN13120:2009+A1:2014, BS EN16433:2014 and BS EN16434:2014.

YewdaleDefiant® fitting instructions Part no: 20006
Fitting Instructions
YewdaleDefiant®cassetted blinds (C20s)
Side Guide Wires:
1.Cutting two lengths of the steel wire, 918003S to length (Blind drop +
100mm), attach the 918011 guide wire clamp to one end of each of the
wires.
NB. By holding the 918011 with pliers, it is important that the screw in this
product is tightened firmly against the wire.
2.Thread the loose end of the wire through the transition plates from the top
(using the back hole provided).
3.Thread the steel wire through the guide holes in the bottom bar end caps,
938313W/B/S.
4.Unscrew both covers of the bezels.
5.Fix the bezels, 918008 directly below 918011W’s (if face fix application us
the face fix adaptor).
6.Thread the steel wire through the bezel cover (from the top).
7.Holding the covers in line with the home position, calculate the length of
the wire and trim to size.
8.Cut the wire to length and securely fasten 918011 wire clamps to the end of
the wire.
NB. By holding the 918011 with pliers, it is important that the screw in this
product is tightened firmly against the wire.
9.Screw the cover caps onto the bezels until the wire is taught.
10.For motor programming instructions, please refer to the enclosed leaflet.
NB. Ensure when the blind is travelling up or down, the cable/bottom bar are
not being pulled out of line.
11.If the blind is spring operated, attach the knot holder to the bottom bar
(along with pull cord and acorn). Attach the cleat to the cill to hold the blind
in the ‘Down’ position.

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 7
Side Guide Wires:
918003S
Steel wire
918008
Bezel with face
fix adaptor 9180011
Guidewire clamp
Diagram
Showing Wire
Connection
938311B/S/W
Tear drop
aluminium bottom bar
938312W/B/S End cap
+938313W/B/S Side
guiding adaptor

Yewdale, Enterprise Way,
Wickford, Essex SS11 8DH
Call [phone]
Fax [phone]
Email [email protected]o.uk
Visit yewdale.co.uk
For more information on all
Yewdale products, please call
the sales department.
curtain track systems
yewdale.co.uk
see things differently
A concise approach to
a broad spectrum of
commercial curtain
track requirements with
simplistic control options
and designed for almost
every application.
®
cubicle and shower screens
yewdale.co.uk
see things differently
A dedicated range of privacy
and shower curtains with a
primary infection control
focus, providing an all-
encompassing solution to
increased levels of dignity.
®
cubicle and track systems
yewdale.co.uk
see things differently
The industry’s preferred
choice of maintenance
free privacy track systems
providing enhanced personal
welfare throughout the entire
healthcare and public sectors.
®
magnetic anti-ligature system
yewdale.co.uk
see things differently
The only fail-safe range of
exclusive anti-ligature products
designed to maximise the
safety of persons by removing
the death potential where
secure care is required.
®
fabric and blind systems
A comprehensive range
of window blind systems
designed with unique
technical features and to
the exacting specifications
that active commercial
environments demand.
yewdale.co.uk
see things differently
®