YewdaleDefiant R42 User manual

Fitting Instructions
for YewdaleDefiant® roller blinds
(R42)
yewdale.co.uk
Fitting Instructions
YewdaleDefiant®roller blinds
(R42)
Part no: 949

YewdaleDefiant® fitting instructions Part no: 9492
Safety Instructions:
1.Loops in pull cords, chains, tapes and inner cords that operate the product
can cause strangulation
2.To avoid strangulation and entanglement, keep cords out of the reach of
young children. Cords may become wrapped around a child’s neck
3.Move beds, cots and furniture away from window covering cords
4. Do not tie cords together. Make sure cords do not twist and create a loop
Fitting Instructions
YewdaleDefiant®roller blinds(R42)
N.B. For more information and child safety device fitting instructions, see Point
9 on Page 7.

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 3

YewdaleDefiant® fitting instructions Part no: 9494
R42 Spring assisted sidewinder control:
N.B. This blind should be installed by a person competent in DIY. If in doubt
please consult a professional.
1. The standard plastic brackets are suitable for face or top-fixing.
2. Check that the blind fits correctly. The spring sidewinder mechanism will
be on the right-hand side, with the fabric rolling o the back of the barrel,
unless a reverse-roll was ordered.
3.Fix the spring-end bracket using appropriate screws/plugs.
4.Locate the blind into the spring sidewinder end bracket, and mark the
position of the pin-end bracket, allowing approximately 2mm free-play
between brackets and blind.
NB. To operate correctly, the blind MUST be fixed level.
Fitting Instructions
YewdaleDefiant®roller blinds(R42)

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 5
R42 Spring assisted sidewinder control:
911929/6 RH
spring assisted sidewinder
911929/8 RH
spring assisted sidewinder
911929/10 RH
spring assisted sidewinder
911940
Retactable pin end
911864
Barrel 36mm
911938W
Bracket set
911938W
Bracket set
913680S
Metal ball chain
938311W/B/S
Tear Drop Bottom Bar
938312W/B/S
Bottom Bar End Cap
926325W
Back Bar Top Fix Bracket
941002W
Braked Spring
Bracket Set
(Back Bar)
933010W
Back Bar
Screw
926325W
Back Bar Top Fix Bracket
938031W
Aluminium Back Bar
OPTIONAL
918003S
Wire
918011
Wire clamp
918008
Side guiding bezel
OPTIONAL
938312W/B/S Endcap
938313W/B/S Side guiding adapter

YewdaleDefiant® fitting instructions Part no: 9496
R42 Spring assisted sidewinder control:
5. Remove the blind and fix the pin-end bracket using appropriate screws/
plugs.
6. Insert the spring sidewinder end of the blind into its bracket. Turn the clear
plastic wheel at the pin-end of the blind to retract pin. Locate the blind into
the pin-end bracket and turn the wheel in the opposite direction to extend
the pin into the bracket.
7. Bring the blind down from its ‘up’ position using the sidewinder control
chain. Now check the blind opens by pulling on the front part of the chain.
With one touch, hold the chain down while the blind rises (intermediate
positions are achieved by letting go of the chain at the desired point). If
the fabric does not wind up completely when the blind is operated, greater
spring tension can be applied as follows:
a) Bring the blind down 250mm from its uppermost position.
b) Remove the blind from the brackets and roll the fabric by hand into
the roller.
c) Replace the blind in the brackets.
d) If tension is still not enough, repeat sets a to c.
e) If tensioned too much, follow the above but in reverse. Remove the
blind from the brackets and unroll the fabric by hand o the roller.
8. Ensure the blind is not over tensioned as the blind is designed to rise to the
top and slow down and stop without the bottom bar hitting the brackets,
otherwise the bottom bar can get trapped between the tube and the wall.
Fitting Instructions
YewdaleDefiant®roller blinds(R42)

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 7
9.Ensure the relevant child safety device is used to comply with BS
EN13120:2009+A1:2014, BS EN16433:2014 and BS EN16434:2014 as follows:
Chain Tidy
The chain tidy will be attached to the chain
when the blind arrives. The chain tidy should
be at a maximum distance from the control
mechanism, keeping the chain taut (not
under excessive tension however as this
could negatively aect the longevity and
operation of the blind). Put the retaining
device on the wall, mark fixing holes with a
pencil, drill the holes and screw the device
to the wall with suitable fixings.

Yewdale, Enterprise Way,
Wickford, Essex SS11 8DH
Call [phone]
Fax [phone]
Email [email protected]
Visit yewdale.co.uk
For more information on all
Yewdale products, please call
the sales department.