YewdaleDefiant F30 User manual

Fitting Instructions
for YewdaleDefiant®Insect screens
(F30)
yewdale.co.uk
Fitting Instructions
YewdaleDefiant®Insect screens
(F30)
Part no: 979

YewdaleDefiant® fitting instructions Part no: 9792
Fitting Instructions
YewdaleDefiant®Insect screens (F30)
Safety Instructions:
1.Loops in pull cords, chains, tapes and inner cords that operate the product
can cause strangulation
2. To avoid strangulation and entanglement, keep cords out of the reach of
young children. Cords may become wrapped around a child’s neck
3.Move beds, cots and furniture away from window covering cords
4. Do not tie cords together. Make sure cords do not twist and create a loop
N.B. For more relevant information and child safety device fitting instructions,
see Point 5 on Page 7.

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 3

YewdaleDefiant® fitting instructions Part no: 9794
F30 Chain Control:
Fitting Instructions
YewdaleDefiant®Insect screens (F30)

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 5
F30 Chain Control – Top Fix:
N.B. This blind should be installed by a person competent in DIY. If in doubt
please consult a professional.
1.The cassette is pre-assembled and does not need to be opened. Check the
positioning of the cassette. (If intermediate brackets are supplied, for wider
units, fix cassette to the recess at equal space using the appropriate screws/
plugs. Fit the cassette to brackets.) Fix the side lugs to the recess using the
appropriate screws/plugs.
2.At minimum 600mm centres, drill 5mm fixing holes in edge of side
channels. Locate side channels to underside of cassette, ensuring that the
bottom bar slides down into the side channels.
3.Fix the side channels using the appropriate screws/plugs. The side channels
MUST be fixed square. Check this by measuring diagonals.
4.Close the screen and adjust the hold-down clips by screwing the top piece in
or out until there is no gap showing below the bottom bar.
F30 Chain Control – Face Fix:
N.B. This blind should be installed by a person competent in DIY. If in doubt
please consult a professional.
1.The cassette is pre-assembled and does not need to be opened. Slide the
brackets onto the cassette, check the positioning, and fix the brackets using
the appropriate screws/plugs.
2.At minimum 600mm centres, drill 10mm holes through front of the side
channels as shown, and 5mm fixing holes through the back.
3.Locate the side channels to the underside of the cassette, ensuring that the
bottom bar slides down into the side channels.
4.Fix the side channels using the appropriate screws/plugs. The side channels
MUST be fixed square. Check this by measuring diagonals. Close the
clearance holes with grommets.
5.Close the screen and adjust the hold-down clips by screwing the top piece in
or out until there is no gap showing below the bottom bar.
NB. To operate correctly, complete blind MUST be level.

YewdaleDefiant® fitting instructions Part no: 9796
Operating Instructions:
1.The cassette should be pre-tensioned at the factory. If it is necessary to
increase/decrease tension, do so as follows:.
2.Remove the fixing screws from the left-hand end cap and carefully prise the
end cap out of the cassette until it is possible to rotate it.
3.Carefully rotate the end cap clockwise to increase the tension or anti-
clockwise to decrease the tension. Refit the end cap.
4.Cut the control chain to the required length and join it using the chain joiner
supplied.
5.To operate the unit, pull the screen down with the ball chain until the
bottom bar clicks into place under the two hold-down clips. To open the
screen, tip the bottom bar back to release it from the hold-down clips, and
allow the screen to retract under the spring tension. Use the ball chain to
fully retract the screen into the cassette.
NB. All chain operated screens are right hand control. It is not possible to fit the
chain to the left side of the cassette.
Fitting Instructions
YewdaleDefiant®Insect screens (F30)

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 7
5.Ensure the relevant child safety devices are used to comply with BS
EN13120:2009+A1:2014, BS EN16433:2014 and BS EN16434:2014.
Chain Tidy
A chain tidy will be attached to the chain
when the blind arrives. The chain tidy should
be at a maximum distance from the control
mechanism, keeping the chain taut (not
under excessive tension however as this could
negatively aect the longevity and operation
of the blind). Put the retaining device on the
wall, mark fixing holes with a pencil, drill the
holes and screw the device to the wall with
suitable fixings.
Easy Break Chain Connectors
An easy break chain connector will be connected to the operating chain. If
excessive weight is applied within the loop the connector will come apart.
If the connector comes apart and is undamaged then it will need to be re-
connected by inserting the last ball on the end of the chain into the hole
with slot in the connector and pushed into place.

Yewdale, Enterprise Way,
Wickford, Essex SS11 8DH
Call [phone]
Fax [phone]
Email [email protected]
Visit yewdale.co.uk
For more information on all
Yewdale products, please call
the sales department.