ACME LED-256D-10W User manual

LED-256D-10W
User Manual
Professional Entertainment Technology
1-
TABLE OF CONTENTS
1. Safety Instruction
2. Technical Specification
3. Installation
4. How to Control the Unit
5. DMX 512 Configuration
6. DMX 512 Connection
7. Fixture Cleaning

2-
1. Safety Instruction
WARNING
♦Please keep this User Manual for future consultation. If you sell the unit to another user,
be sure that they also receive this instruction booklet.
♦Unpack and check carefully there is no transportation damage before using the unit.
♦Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
♦It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
♦The unit is for indoor use only and use only in a dry location.
♦The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
♦Disconnect mains power before fuse replacement or servicing.
♦Replace fuse only with the same type.
♦Make sure there are not flammable materials close to the unit while operating as it is fire
hazard.
♦Use safety cable when fixes this unit.
♦In the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repair carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center and
always use the same type spare parts.
♦Do not touch any wire during operation as high voltage might be causing electric shock.
Please read the instruction carefully which including important
information about the installation, operation and maintenance.
3-
2. Technical Specification
•It can be operated by DMX512 control or can be used as an individual unit without
controller.
•It can be linked together as many as required in master/slave mode, and perform the great
built-in programmed lighting shows triggered by music.
•Please use a 3 pin XLR cable/plug when connecting them together.
•Fan cooled.
•Voltage: AC 100V-240V 50/60Hz
•Fuse: T2A
•Power: 27 W
•LED：1X10W WHITE LED
•Dimension: 210X210X179 mm
•Weight: 1.8kg
3. Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure
to which you are attaching the unit is secure and is able to support a weight of 10 times of
the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the
unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out
of the touch of people and has no one pass by or under it.

4-
4. How To Control The Unit
Three ways to operation:
A. Master/Slave operation
B. Easy controller CA-8
C. Universal DMX controller
A. Master/Slave operation
The unit can be linked together in daisy chain as many as you need in master/slave mode to
perform the great built-in pre-programmed lighting shows triggered by music.
In Master/Slave mode refer to the DMX settings below:
Master unit: DMX start address MUST be set to 001. (First DIP switch = ON, all other
are OFF)
Slave units: DMX start address may have any value but NOT 001 (example: set the
first 3 DIP switches to ON)
﹡Dipswitch 2 “OFF” has functions:
Perform the built-in pre-programmed by music.
﹡Dipswitch 2 “ON” has functions:
Auto mode: Eight Chase(At this mode press dip switch 3 will change the direction of
rotation，press dip switch 4,5,6 will change the speed)
﹡2-light show
Dipswitch 10”off” means the unit works normally and “on” means inversion. In order to
create a great light show, you can set dip switch 10 ”on” on any unit that is linking to the
master unit to get contrast movement to the master unit, even if you have two units only.
Dipswitch 10 on the first (Master) unit is no use for the 2-light show as it is the master unit
that operates the light show.
B. Easy Controller (by CA-8)
The easy remote control is used only in master/slave mode. By connecting to the 1/4”
microphone jack of the first unit (its DMX input plug is not used), you will find that the remote
control all the first unit will control all the other units for Stand by, Function and Mode. Built-in
lighting shows triggered by Easy Controller:
5-
Stand by Blackout the unit
Function
1. Synchronous Strobe
2. Two light Strobe
3. Sound Strobe
Rotation Speed
1-8
Mode Strobe (LED OFF) Rotation (LED ON)
C. Universal DMX controller
When using a universal DMX controller to control the chain of units, you have to set DMX
address by Dip switches from 1 to 9 to make sure all the units will receive its DMX signal.
Dip switch 10 is used to keep OFF. Please refer to the following diagram to know how to
address your DMX 512 system in the binary code.
DMX 512 Address Chart:
Dip-switches # 1 # 2 # 3 # 4 # 5 # 6 # 7 # 8 # 9 #10
Value 1 2 4 8 16 32 64 128 256 Null
•Examples:
Channel 1：dip / on: #1 (=1)
Channel 3：dip / on: #1, #2 (1+2=3)
Channel 5：dip / on:, #1, #3(4+1=5)
Channel 7：dip / on: #1,#2, #3 (1+2+4=7)

6-
5. DMX 512 Configuration
7-
6. DMX 512 Connection
The DMX 512 is widely used in intelligent lightings and with a maximum of 512 channels.
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
adapter-cable.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120
ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin
XLR-plug and plug it in the DMX-output of the last unit.
3. Connect the unit together in a ‘daisy chain’ by XLR plug from the output of the
unit to the input of the next unit. The cable can not be branched or split to a ‘Y’
cable. DMX 512 is a very high-speed signal. Inadequate or damaged cables,
solder joints or corroded connectors can easily distort the signal and shut down
the system.
4. The DMX output and input connectors are pass-through to maintain the DMX
circuit, when power is connected to the unit.
5. Each lighting unit needs to have an address set to receive the data sent by the
controller. The address number is between 0-512 (usually 0 & 1 are equal to 1).
6. The end of the DMX 512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

8-
7. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the unit’s optics.
yClean with soft cloth using normal glass cleaning fluid.
yAlways dry the parts carefully.
yClean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
9-
EC - Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL: 2000+A12: 2002
Safety of household and similar electrical appliances
Part 1: General requirements

10-
11-
Innovation, Quality, Performance