ACME LED-0408 User manual

15-
Technical Specification
Power Input .................…………………………..…...9-12 DC
DMX Output .........................................……………..3 pin female XLR
Audio Input .....................……………….....………….By built-in microphone
Dimensions.....................……………….........……….280 x 170 x 66 mm
Weight......... ...................……............ ......................1.8 kgs
Innovation, Quality, Performance
LIGHT AND EASY
LED-0408
User Guide
Please read these instructions carefully before use

1-
CONTENTS
1. Features.......................................................................................................2
2. General Instruction.......................................................................................3
3. Overview......................................................................................................4
3.1 Front View...........................................................................................4
3.2 Rear View ...........................................................................................5
4. Operation Guide...........................................................................................5
4.1 Store Colour Preset.............................................................................6
4.2 Delete Colour preset...........................................................................6
4.3 Program Chase...................................................................................7
4.4 Insert step to Chase............................................................................7
4.5 Delete Step From Chase.....................................................................8
4.6 Delete Chase......................................................................................9
4.7 Factory Reset......................................................................................9
4.8 Manual Mode....................................................................................10
4.9 Run Colour preset.............................................................................10
4.10 Run CHASE....................................................................................10
4.11 Over control.....................................................................................12
4.12 Strobe .............................................................................................12
4.13 Black Out Mode ..............................................................................12
4.14 Foot Controller (CA-8F )..................................................................13
14-
EC Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55103-1:199601-2; EN55103-2:1996;
EN61000-3-2:2000+A2:2005;
EN61000-3-3:1995+A1:2001+A2:2005.
&
Harmonized Standard
EN 60598-1: 2004
IEC 60598-1:2003+ corrigendum 2004
Part 1:General requirements and test
Following the provisions of the low voltage directive 73/23/EEC and 93/68/EEC

13-
4.14 Foot Controller (CA-8F)
LED-0408 can work with CA-8F, when the CA-8F connect with the
LED-0408, pressing the BLACKOUT button on LED-0408 for 3
seconds to active the CA-8F; pressing the STANDBY button on
CA-8F for 3 seconds to active the LED-0408. When the STAND BY indicator is blinking,
means the LED-0408 is active, when the indicator is not blinking, means the CA-8F is
active. The functions are shown below:
CA-8F
STAND BY (LED1) LED blinking LED off LED on
SWITCH TO
LED-0408 CA-8F ACTIVATE STAND BY
FUNCTION CHASE
SELECT NEXT STEP STROBE
ACTIVATE
MODE(LED2) LED on LED blinking LED off
MUSIC RUN MANUAL RUN STROBE
2-
1. Features
1. Light and Easy is an user friendly LED controller.
2. Designed to work on all 4-Channel LED lighting fixtures
3. Control up to 32 channels of 8 LED groups
4. 8 individual button s for selecting 8 groups of lighting fixtures
5. LED display for easy navigation
6. 8 Colour pre-set buttons with 4 Banks, 32 pre-set colours in total.
7. 8 Chases, each can save up to 32 scenes
8. 3 operation modesAuto, Sound, Manual.
9. Blackout function and instant strobe access button with variable speed.
10. Optional Foot Controller (CA-8F) for ease of operation.
NOTE:
A knowledge of DMX is required to fully utilize this unit.

3-
2. General Instruction
Please read the user manual carefully, as it includes important information regarding
details of operation, maintenance, and technical data. Keep this manual with the unit for
future consult.
WARNINGS！
yAvoid any inflammable liquids, water or metal objects entering the unit.
yShould any liquid be spilled on the unit, DISCONNECT the power supply to the unit
immediately.
ySTOP using the unit immediately In the event of serious operation problems and either
contact your local dealer for a check immediately.
yDO NOT open the unit--there are no user serviceable parts inside.
yNEVER try to repair the unit yourself. Repairs by unqualified people could cause
damage or malfunction.
CAUTIONS！
yThis unit is NOT intended for home use.
yAfter removing the packing Make that the unit is NOT damaged in any way. If in doubt,
DON'T use it and contact an authorized dealer.
yPackaging material (plastic bags, polystyrene foam, nails, etc.) MUST NOT be left
within children's reach, as it can be dangerous.
yThis unit must only be operated by adults. DO NOT allow children to tamper or play
with it.
yNEVER use the unit under the following conditions:
In places subject to excessive humidity.
In places subject to vibrations or bumps.
In places with a temperature of over 45 C/113 F or less than 2 C/35.6 F.
yProtect the unit from excessive dryness or humidity (ideal conditions are between 35%
and 80%).
yDO NOT dismantle or modify the unit.
12-
4.11 Over control
It can be used to manually control units when running COLOUR PRESET or CHASE.
1 Ensure the LED above BLACK OUT button is off.
2 Run COLOUR PRESET or CHASE directly.
3 Press FIXTURE SELECTOR 1-8 button to choose units.
4 Push FADER 1-4 to adjust the lighting effect, the changes of the
channel values are in dependent of the COLOUR PRESET or
CHASE.
5 Back to the normal mode, please press DEL/CLEAR button.
4.12 Strobe
Press STROBE button when BLACK OUT LED on or off, all the units will
strobe, at the same time you can jog STROBE SPEED fader to adjust the
strobe speed (1Hz-20Hz).
4.13 Black Out Mode
There are 3 kinds of black out mode that indicate by the LED.
1 LED off: LED-0408 is active.
2 LED on: Pressing BLACK OUT button, corresponding LED on,
all units blackout and outputs become “0” (exception
the STROBE is still active).
3 LED blinking: Pressing BLACK OUT button for 3 seconds,
corresponding LED blinking, the units control by FOOT
CONTROLLOER (CA-8F), all the buttons will not work expect
BLACK OUT button, so you can press to back to LED off mode
and control by LED-0408.

11-
the MANUAL LED on indicating into Manual Mode.
4 Press UP/DOWN button to change the step, UP to the last step,
DOWN to the next step.
B. Sound Mode
1 Insure the LED above BLACK OUT is off.
2 Press CHASE 1-8 button to run the CHASE, the display will
show the present CHASE.
3 Press MANUAL/MUSIC/AUTO button to choose Sound
Mode, the MUSIC LED on indicating Sound Mode.
4 Press UP/DOWN button to adjust the sound sensitivity, the
CHASE will run to the music.
C. Auto mode
1 Insure the LED above BLACK OUT button is off.
2 Press CHASE 1-8 button，the display will show the present
CHASE.
3 Press MANUAL/MUSIC/AUTO button to choose Auto Mode,
the AUTO LED on indicating Auto Mode.
4 Push CHASE SPEED FADER to adjust the CHASE speed, push
FADE FADER to adjust the fade time (the percent of the chase
speed). Press UP/DOWN button to set the run time for CHASE
(It’s useful when you run more than one CHASE at one time).
You can also change the CHASE speed via INSERT/TAP
button. When running the CHASE, press the INSERT/TAP
button and the indicator will blinking, then press the
INSERT/TAP button and the indicator off, the blinking time will
be the CHASE speed.
4-
3. Overview
3.1 Front View
FIXTURE SELECTOR 1-8 use to select fixtures
COLOUR PRESETS 1-8 select 32 colours by UP/SOWN button
CHASE 1-8 use to select chase 1-8
PROGRAM/REC enter or exit program/record function
INSERT/TAP Insert one step/set up a tap for chase
DEL/CLEAR delete preset colour, chase or step/clean output,
UP/DOWN select bank, run chase manually, adjust the sound
sensitivity and the times chase auto run.
MANUAL/MUSIC/AUTO use to select running mode, the corresponding LED on
indicating Manual Mode, Sound Mode or Auto Mode.
BLACK OUT use to select black out mode or switch to CA-8 control
FLASH strobe function
FADER 1-4 use to adjust the output of 1-4 channels
STROBE SPEED FADER use to adjust the strobe speed (1-20Hz)
CHASE SPEED FADER use to adjust the chase speed, the run time of each step
can be set from 0.1S to 60M.
FADE FADER use to adjust the fade which show as percentage of the
run time