Amazone Cataya 3000 Special User manual
Operating manual
az
Pack top seed drill
Cataya 3000 Special
MG6505
BAH0103-0 04.19
Please read and observe this
operating manual before initial
operation of the implement!
Keep it in a safe place for future use!
en
2 Cataya Special BAH0103-0 04.19
Reading the instruction
manual and to adhere to it should not appear to
be inconvenient and superfluous as it is not
enough to hear from others and to realise that a
machine is good, to buy it and to believe that now
everything would work by itself. The person
concerned would not only harm himself but also
make the mistake of blaming the machine for the
reason of a possible failure instead of himself. In
order to ensure a good success one should go into
the mind of a thing or make himself familiar with
every part of the machine and to get acquainte
d
with its handling. Only this way, you would be
satisfied both with the machine as also with
yourself. To achieve this is the purpose of this
instruction manual.
Leipzig-Plagwitz 1872.
Identification data
Cataya Special BAH0103-0 04.19 3
Identification data
Please insert the identification data of the implement. The
identification data are arranged on the rating plate.
Implement number (ten digits):
Type:
Year of manufacture:
Basic weight [kg]:
Permissible total weight [kg]:
Maximum load [kg]:
Manufacturer address
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Postfach 51
D-49202
Tel.:
Email:
Hasbergen, Germany
+ 49 (0) 5405 50 1-0
Spare Parts Order
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Type: Cataya Special
Document number: MG6505
Compilation date: 04.19
Copyright AMAZONEN-WERKE H. DREYER GmbH & Co. KG, 2019
All rights reserved.
Reprinting, even of sections, only possible with the approval of
AMAZONEN-WERKE H. DREYER GmbH & Co. KG.
Foreword
4 Cataya Special BAH0103-0 04.19
Foreword
Dear Customer,
You have chosen one of the quality products from the wide product range of AMAZONEN-WERKE,
H. DREYER GmbH & Co. KG. We thank you for your trust in our products
On receiving the implement, check to see if it has been damaged during transport or if parts are
missing. Using the delivery note, check that the implement has been delivered in full, including any
special equipment ordered. Damage can only be rectified if problems are claimed immediately.
Before initial operation, read and observe this operating manual, and particularly the safety information.
Only after careful reading will you be able to benefit from the full scope of your newly purchased
implement.
Please ensure that all the implement operators have read this operating manual before they put the
implement into operation.
Should you have any questions or problems, please consult this operating manual or contact your
local service partner.
Regular maintenance and timely replacement of worn or damaged parts increases the service life of
your implement.
Cataya Special BAH0103-0 04.19 5
1User information ........................................................................................ 10
1.1Purpose of the document ....................................................................................................... 10
1.2Locations in the operating manual ......................................................................................... 10
1.3Diagrams ................................................................................................................................ 10
2General safety instructions ....................................................................... 12
2.1Obligations and liability .......................................................................................................... 12
2.2Representation of safety symbols .......................................................................................... 14
2.3Organisational measures ....................................................................................................... 15
2.4Safety and protective equipment ........................................................................................... 15
2.5Informal safety measures ....................................................................................................... 15
2.6User training ........................................................................................................................... 16
2.7Safety measures in normal operation .................................................................................... 17
2.8Danger from residual energy ................................................................................................. 17
2.9Maintenance and repair work, fault elimination ..................................................................... 17
2.10Design changes ..................................................................................................................... 18
2.10.1Spare and wear parts and aids .............................................................................................. 19
2.11Cleaning and disposal ............................................................................................................ 19
2.12User workstation .................................................................................................................... 19
2.13Warning symbols and other labels on the implement ............................................................ 20
2.13.1Position of warning symbols .................................................................................................. 2 6
2.14Dangers in case of non-compliance with the safety instructions ........................................... 27
2.15Safety-conscious working ...................................................................................................... 27
2.16Safety information for users ................................................................................................... 28
2.16.1General safety instructions and accident prevention instructions .......................................... 28
2.16.2Hydraulic system .................................................................................................................... 32
2.16.3Electrical system .................................................................................................................... 33
2.16.4Mounted implements .............................................................................................................. 34
2.16.5Operation of the seed drill ...................................................................................................... 35
2.16.6Cleaning, maintenance and repair ......................................................................................... 35
3Loading and unloading the implement upon delivery ............................ 36
4Product description ................................................................................... 38
4.1Components of the AMAZONE seeding combination ........................................................... 38
4.2Equipment variations of the Cataya pack top seed drill ......................................................... 39
4.3Assembly groups of the Cataya pack top seed drill ............................................................... 41
4.4Safety and protective equipment ........................................................................................... 43
4.5Overview – Supply cable / hydraulic hose lines ..................................................................... 45
4.5.1Supply cable........................................................................................................................... 45
4.5.2Identification of the hydraulic hose lines ................................................................................ 45
4.5.2.1Type of actuation of the tractor control units .......................................................................... 45
4.5.3Connection and function of the tractor control units .............................................................. 46
4.6Traffic safety equipment ......................................................................................................... 47
4.7Intended use .......................................................................................................................... 48
4.7.1Approved AMAZONE implement combinations ..................................................................... 49
4.8Danger areas and danger points ........................................................................................... 50
4.9Rating plate and CE mark ...................................................................................................... 51
4.10Technical data ........................................................................................................................ 52
4.11Noise production data ............................................................................................................ 52
4.11.1Technical data for calculating the tractor weight and the tractor axle loads .......................... 53
4.12Required tractor equipment ................................................................................................... 5 4
5Layout and function ................................................................................... 55
6 Cataya Special BAH0103-0 04.19
5.1AMAZONE AmaLog+ control terminal .................................................................................. 58
5.2AMAZONE AmaDrill 2 control terminal ................................................................................. 58
5.3AMAZONE calibration button ................................................................................................ 59
5.4Control terminal for implements with ISOBUS system .......................................................... 59
5.4.1AMAZONE AmaTron 4 control terminal ................................................................................ 60
5.5AMAZONE TwinTerminal ...................................................................................................... 60
5.6Implement documentation ..................................................................................................... 61
5.7Central key ............................................................................................................................ 61
5.8Star wheel ............................................................................................................................. 62
5.9Radar device ......................................................................................................................... 63
5.10Seed hopper and loading board ............................................................................................ 64
5.10.1Fill level monitoring ................................................................................................................ 65
5.11Seeding shaft drive................................................................................................................ 66
5.11.1Seeding shaft drive of one star wheel ................................................................................... 66
5.11.1.1Extending the range of the Vario gearbox ............................................................................ 67
5.11.2Seeding shaft drive, electrically regulated ............................................................................ 67
5.12Metering ................................................................................................................................ 68
5.12.1Setting values ........................................................................................................................ 70
5.12.1.1Coarse and fine metering wheel ........................................................................................... 72
5.12.1.2Bean metering wheel............................................................................................................. 72
5.12.1.3Bottom flaps .......................................................................................................................... 73
5.12.1.4Slide gate .............................................................................................................................. 74
5.12.1.5Agitator shaft support ............................................................................................................ 74
5.13Seed rate calibration ............................................................................................................. 75
5.13.1Calibration - Implements with star wheel drive ..................................................................... 78
5.13.2Calibration - Implements with electric seeding shaft drive .................................................... 80
5.14RoTeC Control coulter .......................................................................................................... 81
5.15Coulter pressure .................................................................................................................... 83
5.15.1Coulter pressure - manually actuated ................................................................................... 83
5.15.2Coulter pressure, hydraulically actuated with seed rate increase ......................................... 84
5.16Soil tillage without seeding (coulter lift) ................................................................................. 86
5.17Exact following harrow .......................................................................................................... 87
5.17.1Exact following harrow tine position ...................................................................................... 88
5.17.2Exact following harrow pressure ........................................................................................... 89
5.18Tramlines ............................................................................................................................... 90
5.18.1Tramline rhythm, tabular determination ................................................................................ 93
5.18.2Tramline rhythm, graphic determination................................................................................ 94
5.19One-sided switching .............................................................................................................. 96
5.20Tramline marker .................................................................................................................... 97
5.21Track marker ......................................................................................................................... 98
5.22Work floodlights ..................................................................................................................... 99
6Commissioning ....................................................................................... 100
6.1Checking the suitability of the tractor .................................................................................. 101
6.1.1Calculating the actual values for the total tractor weight, tractor axle loads and tyre
load-bearing capacity, as well as the required minimum ballast weight ............................. 102
6.1.1.1Data required for the calculation (attached implement) ...................................................... 103
6.1.1.2Calculation of the required minimum ballast weight at the front GV min of the tractor
to ensure steering capability ............................................................................................... 104
6.1.1.3Calculation of the actual front axle load of the tractor TV tat ................................................. 104
6.1.1.4Calculation of the actual total weight of the combined tractor and implement .................... 104
6.1.1.5Calculation of the actual rear axle load of the tractor TH tat ................................................. 104
6.1.1.6Load-bearing capacity of the tractor tyres ........................................................................... 104
6.1.1.7Table ................................................................................................................................... 105
6.2Secure the tractor / implement against unintentional starting and rolling away ................. 106
7Coupling and uncoupling the implement .............................................. 107
7.1Hydraulic hose lines ............................................................................................................ 109
Cataya Special BAH0103-0 04.19 7
7.1.1Coupling the hydraulic hose lines ........................................................................................ 109
7.1.2Disconnecting the hydraulic hose lines ................................................................................ 110
7.2Coupling and uncoupling implements .................................................................................. 111
7.2.1Coupling - Tractor and soil tillage implement ....................................................................... 113
7.2.1.1Installation of the analogue working position sensor ........................................................... 114
7.3Coupling - Pack top seed drill and soil tillage implement .................................................... 116
7.3.1Uncoupling – Combination from the tractor ......................................................................... 121
7.3.2Uncoupling – Soil tillage implement and pack top seed drill ............................................... 122
7.4Checking the tramline track width ........................................................................................ 127
7.5Checking the tramline wheelmark width .............................................................................. 127
8Settings ..................................................................................................... 128
8.1Folding the steps up and down ............................................................................................ 129
8.2Fill the seed hopper ............................................................................................................. 131
8.3Setting the seed rate ............................................................................................................ 134
8.3.1Bottom flap position ............................................................................................................. 134
8.3.2Sliding shutter position ......................................................................................................... 135
8.3.3Agitator shaft support ........................................................................................................... 136
8.3.3.1Agitator shaft support (implements with star wheel drive) ................................................... 136
8.3.3.2Agitator shaft support (implements with electric metering drive) ......................................... 137
8.4Calibrating the seed rate ...................................................................................................... 138
8.4.1Calibrating the seed rate - implements with star wheel drive .............................................. 142
8.4.1.1Preparing the implement for calibration ............................................................................... 142
8.4.1.2Pre-calibrating the implement .............................................................................................. 143
8.4.1.3Calibrating the seed rate ...................................................................................................... 144
8.4.1.4Determining the gearbox setting using the calculating disc rule .......................................... 146
8.4.2Calibrating the seed rate Implements with AmaDrill 2 control terminal, Implements
with ISOBUS system ............................................................................................................ 147
8.4.3Adjusting the automatic seed rate increase ......................................................................... 148
8.5Star wheel – Working and transport position ....................................................................... 149
8.6RoTeC Control coulter ......................................................................................................... 150
8.6.1Adjusting and checking the seed placement depth ............................................................. 150
8.6.1.1Adjusting the depth control discs / wheels ........................................................................... 151
8.7Coulter pressure .................................................................................................................. 153
8.7.1Coulter pressure adjustment (manual adjustment) .............................................................. 153
8.7.2Coulter pressure adjustment (hydraulic adjustment) ........................................................... 154
8.8Adjusting the exact following harrow ................................................................................... 155
8.8.1Adjusting the exact following harrow tines ........................................................................... 155
8.8.2Setting the exact following harrow pressure ........................................................................ 156
8.8.3Moving the exact following harrow to the working/transport position .................................. 157
8.8.3.1Move the exact following harrow into working position ........................................................ 157
8.8.3.2Moving the exact following harrow into transport position ................................................... 157
8.9Moving the track marker to the working / transport position ................................................ 158
8.9.1Move track marker to working position ................................................................................ 158
8.9.2Moving the track marker to transport position ...................................................................... 160
8.10One-sided switching ............................................................................................................. 161
8.11Moving the tramline marker into working/transport position ................................................ 162
8.11.1Move the tramline marker to working position ..................................................................... 162
8.11.2Move the tramline markers to the transport position............................................................ 163
8.12Moving the exact following harrow road safety bar into road transport/parking
position ................................................................................................................................. 164
8.12.1Moving the road safety bar into road transport position ...................................................... 164
8.12.2Moving the road safety bar into parking position ................................................................. 164
8.13Soil tillage without seeding ................................................................................................... 165
8.13.1Lifting the coulters and exact following harrow .................................................................... 165
8.13.2Moving the coulters and exact following harrow into working position ................................ 166
9Transportation ......................................................................................... 167
9.1Moving the seeding combination into transport position ...................................................... 167
8 Cataya Special BAH0103-0 04.19
9.2Legal regulations and safety ............................................................................................... 168
10Use of the implement .............................................................................. 172
10.1Initial operation .................................................................................................................... 173
10.2Work floodlights ................................................................................................................... 173
10.3Moving the implement from transport into working position ................................................ 174
10.4Work commencement ......................................................................................................... 174
10.5During operation .................................................................................................................. 176
10.5.1Overview of checks during operation .................................................................................. 176
10.5.2Turning at end of the field ................................................................................................... 177
10.5.3Track marker ....................................................................................................................... 178
10.5.4End of work on the field ....................................................................................................... 178
10.6Emptying the seed hopper and seed housing ..................................................................... 179
11Faults ........................................................................................................ 183
11.1Residual seed quantity display ............................................................................................ 184
11.2Deviations between the set and actual seed rate ............................................................... 184
12Cleaning, maintenance and repairs ....................................................... 185
12.1Safety .................................................................................................................................. 185
12.1.1Safety when working on hydraulic hose lines ..................................................................... 187
12.1.1.1Safety through labelling the hydraulic hose lines ................................................................ 188
12.2Safety when cleaning the implement .................................................................................. 189
12.3Shutdown of the implement over a long period of time ....................................................... 190
12.4Maintenance schedule ........................................................................................................ 191
12.5Work to be performed in a specialist workshop .................................................................. 192
12.5.1Checking the hydraulic hose lines ....................................................................................... 192
12.6Mounting instructions .......................................................................................................... 193
12.6.1Opening and closing the function flap ................................................................................. 193
12.6.2Opening and closing the cover ............................................................................................ 194
12.7Tramline control ................................................................................................................... 195
12.7.1Folding down the countershaft ............................................................................................ 197
12.7.2Folding up the countershaft ................................................................................................. 198
12.7.3Setting the tramline track width ........................................................................................... 199
12.7.4Setting the tramline wheelmark width ................................................................................. 200
12.7.5Conversion of a metering wheel to a tramline metering wheel ........................................... 201
12.7.6Conversion of a tramline metering wheel to a metering wheel ........................................... 203
12.7.6.1Conversion of a tramline metering wheel to a metering wheel by shifting the gear
wheel on the countershaft ................................................................................................... 203
12.7.6.2Conversion of a tramline metering wheel to a metering wheel by removing the gear
wheel pairing from the lay shaft and seeding shaft ............................................................. 204
12.8Changing the metering wheel ............................................................................................. 205
12.8.1Changing the metering wheel - Seeding shaft drive with star wheel .................................. 205
12.8.2Changing the metering wheel - Seeding shaft drive with an electric motor ........................ 210
12.8.3Check the chain tension ...................................................................................................... 216
12.9Extending the range of the Vario gearbox .......................................................................... 217
12.9.1Visual inspection of the upper and lower link pins .............................................................. 221
12.10Bolt tightening torques ........................................................................................................ 221
13Hydraulic diagram ................................................................................... 224
13.1Hydraulic diagram Cataya 3000 Special ............................................................................. 224
Cataya Special BAH0103-0 04.19 9
User information
10 Cataya Special BAH0103-0 04.19
1 User information
The User Information section provides information on use of the operating manual.
This operating manual is valid for all versions of the implement.
Figures serve as a reference and are to be understood as representations of the principle.
All of the equipment is described without indicating it as special equipment. A description may be
provided for equipment that is not fitted on the implement or is only available in certain markets. The
sales documents provide information on the equipment of your implement or consult your service
partner for more detailed information.
All information in this operating manual corresponds to the state of knowledge at the time of
publication. Due to ongoing development of the implement, deviations are possible between the
implement and the information in this operating manual. No claims can be made based on differences
in the specifications, figures or descriptions.
If you want to sell the implement, ensure that the operating manual is supplied with the implement.
1.1 Purpose of the document
This operating manual
describes the operation and maintenance of the implement
provides important information on safe and efficient handling of
the implement
is an integral part of the implement and should always be kept
with the implement or the towing vehicle
must be kept in a safe place for future use.
1.2 Locations in the operating manual
A
ll the directions specified in the operating manual are always seen in
the direction of travel.
1.3 Diagrams
Instructions and responses
Activities to be carried out by the user are given as numbered
instructions. Always keep to the order of the instructions. The reaction
to the handling instructions is given by an arrow. Example:
1. Instruction 1
Reaction of the implement to handling instruction 1
2. Instruction 2
User information
Cataya Special BAH0103-0 04.19 11
Lists
Lists without an essential order are shown as a list with bullets.
Example:
Point 1
Point 2
Item numbers in diagrams
Numbers in round brackets refer to the item numbers in the diagrams.
The first number refers to the diagram and the second number to the
item.
Example (Fig. 3/6):
Figure 3
Item 6
General safety instructions
12 Cataya Special BAH0103-0 04.19
2 General safety instructions
This section contains important information on safe operation of the
implement.
2.1 Obligations and liability
Comply with the instructions in the operating manual
Knowledge of the basic safety information and safety regulations is a
basic requirement for safe handling and fault-free implement
operation.
Obligations of the operator
The operator is obliged only to let those people work with/on the
implement who
are aware of the basic workplace safety information and accident
prevention regulations
have been trained in working with/on the implement
have read and understood this operating manual.
The operator is obliged
to keep all the warning symbols on the implement in a legible
state
to replace damaged warning symbols.
Obligations of the user
Before starting work, anyone charged with working with/on the
implement is obliged
to comply with the basic workplace safety instructions and
accident prevention regulations
to read and understand the "General safety information" section
of this operating manual
to read the section "Warning symbols and other labels on the
implement" in this operating manual and to follow the safety
instructions represented by the warning symbols when operating
the implement
to get to know the implement
to read the sections of this operating manual, important for
carrying out your work.
If the user discovers that a function is not working properly, then they
must eliminate this fault immediately. If this is not the task of the user
or if the user does not have the appropriate technical knowledge, then
they should report this fault to their superior (operator).
General safety instructions
Cataya Special BAH0103-0 04.19 13
Risks in handling the implement
The implement has been constructed to the state-of-the art and the
recognised rules of safety. However, operating the implement may
cause risks and restrictions
the health and safety of the user or third persons
the implement itself
other property.
Only use the implement
for the purpose for which it was intended
in a perfect state of repair.
Eliminate any faults immediately which could impair safety.
Guarantee and liability
Our "General conditions of sales and delivery" are always applicable.
These shall be available to the operator, at the latest on conclusion of
the contract. Guarantee and liability claims for damage to people or
property will be excluded if they can be traced back to one or more of
the following causes:
Improper use of the implement
Improper installation, commissioning, operation and
maintenance of the implement
Operation of the implement with defective safety equipment or
improperly attached or non-functioning safety and protective
equipment
Non-compliance with the instructions in the operating manual
regarding commissioning, operation and maintenance
Unauthorised design changes to the implement
Insufficient monitoring of implement parts which are subject to
wear
Improperly executed repairs
Disasters due to the effects of foreign objects and force majeure.
General safety instructions
14 Cataya Special BAH0103-0 04.19
2.2 Representation of safety symbols
Safety instructions are indicated by the triangular safety symbol and
the highlighted signal word. The signal word (DANGER, WARNING,
CAUTION) describes the severity of the risk, and carries the following
meaning:
DANGER
Indicates a direct threat at high risk which will result in death or
most serious bodily harm (loss of limbs or long-term harm),
should it not be prevented.
If the instructions are not followed, then this will result in
immediate death or serious physical injury.
WARNING
Indicates a medium risk, which could result in death or (serious)
physical injury if not avoided.
If the instructions are not followed, then this may result in death
or serious physical injury.
CAUTION
Indicates a low risk which could cause minor or medium level
physical injury or damage to property if not avoided.
IMPORTANT
Indicates an obligation to special behaviour or an activity
required for proper machine handling.
Non-compliance with these instructions can cause faults on the
machine or disturbance to the environment.
NOTE
Indicates handling tips and particularly useful information.
These instructions will help you to use all the functions of your
machine in the best way possible.
General safety instructions
Cataya Special BAH0103-0 04.19 15
2.3 Organisational measures
The operator must provide the necessary personal protective
equipment as per the information provided by the manufacturer of the
crop protection agent to be used, such as:
Safety glasses
Protective shoes
Chemical-resistant overalls
Skin protection agents, etc.
The operation manual
must always be kept at the place at which the implement is
operated
must always be easily accessible for the user and maintenance
personnel.
Check all the available safety equipment regularly.
2.4 Safety and protective equipment
Before starting up the implement each time, all the safety and
protection equipment must be properly attached and fully functional.
Check all safety and protection equipment regularly.
Faulty safety equipment
Faulty or disassembled safety and protection equipment can lead to
dangerous situations.
2.5 Informal safety measures
As well as all the safety information in this operating manual, comply
with the general, national regulations pertaining to accident prevention
and environmental protection.
When driving on public roads and routes you should comply with the
statutory road traffic regulations.
General safety instructions
16 Cataya Special BAH0103-0 04.19
2.6 User training
Only those people who have been trained and instructed may work with/on the implement. The
operator must clearly specify the responsibilities of the people charged with operation and
maintenance work.
People being trained may only work with/on the implement under the supervision of an experienced
person.
Person
Job
Person specially
trained for the
activity 1)
Trained
person 2)
Persons with
specialist
training (specialist
workshop) 3)
Loading/Transport X X X
Commissioning X
Set-up, tool installation X
Operation X
Maintenance X
Troubleshooting and fault
elimination
X X
Disposal X
Legend: X..permitted ..not permitted
1) A person who can assume a specific task and who can carry out this task for an appropriately
qualified company.
2) Instructed persons are those who have been instructed in their assigned tasks and in the
possible risks in the case of improper behaviour, have been trained if necessary, and have been
informed about the necessary protective equipment and measures.
3) Persons with specialised technical training shall be considered as a specialist. Due to their
specialist training and their knowledge of the appropriate regulations, they can evaluate the work
with which they have been charged and detect possible dangers.
Comment:
A qualification equivalent to specialist training can be obtained from several years' experience in
the relevant field.
Only a specialist workshop may carry out maintenance and repair
work on the implement, if such work is additionally marked
"Workshop". The personnel of a specialist workshop shall possess the
appropriate knowledge and suitable aids (tools, lifting and support
equipment) for carrying out the maintenance and repair work on the
implement in a way which is both appropriate and safe.
General safety instructions
Cataya Special BAH0103-0 04.19 17
2.7 Safety measures in normal operation
Only operate the implement if all the safety and protection equipment
is fully functional.
Check the implement at least once a day for visible damage and
check the function of the safety and protection equipment.
2.8 Danger from residual energy
Note that there may be residual mechanical, hydraulic, pneumatic and
electrical/electronic energy on the implement.
Use appropriate measures to inform the operator. You can find
detailed information in the relevant sections of this operating manual.
2.9 Maintenance and repair work, fault elimination
Carry out prescribed setting, maintenance and inspection work in
good time.
Secure all media such as compressed air and the hydraulic system
against unintentional start-up.
Carefully fix and secure larger assembly groups to lifting gear when
carrying out replacement work.
Check all the bolted connections for tightness. On completion of the
maintenance work, check the function of the safety and protective
devices.
General safety instructions
18 Cataya Special BAH0103-0 04.19
2.10 Design changes
You may make no changes, expansions or modifications to the
implement without the authorisation of AMAZONEN-WERKE. This
also applies when welding support parts.
A
ny extension or conversion work shall require the written approval of
AMAZONEN-WERKE. Only use conversion and special equipment
parts approved by AMAZONEN-WERKE so that the operating permit,
for example, remains valid in accordance with national and
international regulations.
Vehicles with an official type approval or with equipment connected to
a vehicle with a valid type approval or approval for road transport
according to the German road traffic regulations must be in the state
specified by the approval.
WARNING
Risk of crushing, cutting, being trapped or drawn in, or impact
through the failure of support parts.
It is strictly forbidden to
drill holes in the frame or on the running gear
increase the size of existing holes on the frame or the running gear
weld on load-bearing parts.
General safety instructions
Cataya Special BAH0103-0 04.19 19
2.10.1 Spare and wear parts and aids
Immediately replace any implement parts which are not in a perfect
state.
Use only genuine AMAZONE spare and wear parts or the parts
cleared by AMAZONEN-WERKE so that the operating permit retains
its validity in accordance with national and international regulations. If
you use wear and spare parts from third parties, there is no guarantee
that they have been designed and manufactured in such a way as to
meet the requirements placed on them.
AMAZONEN-WERKE shall accept no liability for damage caused by
the use of non-approved spare and wear parts or aids.
2.11 Cleaning and disposal
Handle and dispose of any materials used carefully, in particular
when carrying out work on lubrication systems and equipment
and
when cleaning using solvents.
2.12 User workstation
The implement may be operated by only one person sitting in the
driver's seat of the tractor.
General safety instructions
20 Cataya Special BAH0103-0 04.19
2.13 Warning symbols and other labels on the implement
Always keep all the warning symbols of the implement clean and in a
legible state! Replace illegible warning symbols. You can request the
warning symbols from your AMAZONE dealer using the order number
(e.g., MD 075).
Structure
Warning symbols indicate danger areas on the implement and warn
against residual dangers. At these points, there are permanent or
unexpected dangers.
A warning symbol consists of two fields:
Field 1
Shows the danger in a triangular safety symbol.
Field 2
Shows instructions for avoiding the danger.
Explanatory text beside the warning symbol
The text beside the warning symbol describes
1. The dangers, e.g.:
Laceration or amputation hazard.
2. The consequence of non-compliance with the risk avoidance
instructions, e.g.:
This danger can cause serious injuries to fingers or hands.
3. Instructions for avoiding the risk, e.g.:
Touch machinery parts only when they have come to a complete
stop.
Other manuals for Cataya 3000 Special
1
Table of contents
Other Amazone Farm Equipment manuals
Amazone
Amazone KG Special Series User manual
Amazone
Amazone Centaur 3002 User manual
Amazone
Amazone VK70181000 User manual
Amazone
Amazone Groundkeeper Jumbo SMARTCUT User manual
Amazone
Amazone Cenius 4002-2T Super User manual
Amazone
Amazone UX 6201 Super User manual
Amazone
Amazone ZA-X Perfect 602 User manual
Amazone
Amazone Catros 5003-2TS Installation instructions
Amazone
Amazone Hektor User manual
Amazone
Amazone Catros 4003-2 Installation instructions
Amazone
Amazone DMC Primera 12001-2C User manual
Amazone
Amazone Cayros M Installation instructions
Amazone
Amazone AD-P 3001 Special 850 User manual
Amazone
Amazone Cataya User manual
Amazone
Amazone ZA-M premiS User manual
Amazone
Amazone ZG-TS 7501 Truck User manual
Amazone
Amazone DMC Primera 3000 User manual
Amazone
Amazone Pantera 4504 User manual
Amazone
Amazone AD 3000 Super Classic Line User manual
Amazone
Amazone XTender 2200 User manual
