Amazone AD 3000 Super Classic Line User manual
Operating manual
az
Pack top seed drill
AD 3000 Super
Classic Line
MG6820
BAH0107-0 02.20
Please read and observe this
operating manual before initial
operation of the implement!
Keep it in a safe place for future use!
en
AD 3000 Super BAH0107-0 02.20 3
Identification data
Please insert the identification data of the implement. The
identification data are arranged on the rating plate.
Type: AD 3000 Super Classic Line
Implement number (ten digits):
Year of manufacture:
Permissible total weight [kg]:
Manufacturer address
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Postfach 51
D-49202
Tel.:
E-mail:
Hasbergen, Germany
+ 49 (0) 5405 50 1-0
Spare Parts Order
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Type: AD 3000 Super Classic Line
Document number: MG6820
Compilation date: 02.20
Copyright AMAZONEN-WERKE H. DREYER GmbH & Co. KG, 2020
All rights reserved.
Reprinting, even of sections, permitted only with the approval of
AMAZONEN-WERKE H. DREYER GmbH & Co. KG.
4 AD 3000 Super BAH0107-0 02.20
Foreword
Dear Customer,
You have chosen one of the quality products from the wide product range of AMAZONEN-WERKE,
H. DREYER GmbH & Co. KG. We thank you for your trust in our products.
On receiving the implement, check to see if it has been damaged during transport or if parts are
missing. Using the delivery note, check that the implement has been delivered in full, including any
special equipment ordered. Damage can only be rectified if problems are claimed immediately.
Before initial operation, read and comply with the information in this operating manual, and particularly
the safety instructions. Only after careful reading will you be able to benefit from the full scope of your
newly purchased implement.
Please ensure that all the implement operators have read this operating manual before they put the
implement into operation.
Should you have any questions or problems, please consult this operating manual or contact your
local service partner.
Regular maintenance and timely replacement of worn or damaged parts increases the service life of
your implement.
AD 3000 Super BAH0107-0 02.20 5
1User information ........................................................................................ 10
2General Safety Instructions ...................................................................... 11
2.1Obligations and liability .......................................................................................................... 11
2.2Representation of safety symbols .......................................................................................... 13
2.3Organisational measures ....................................................................................................... 14
2.4Safety and protective equipment ........................................................................................... 14
2.5Informal safety measures ....................................................................................................... 14
2.6User training ........................................................................................................................... 15
2.7Safety measures in normal operation .................................................................................... 16
2.8Danger from residual energy ................................................................................................. 16
2.9Maintenance and repair work, fault elimination ..................................................................... 16
2.10Design changes ..................................................................................................................... 16
2.10.1Spare and wear parts and aids .............................................................................................. 17
2.11Cleaning and disposal ............................................................................................................ 17
2.12Workstation of the operator .................................................................................................... 17
2.13Warning symbols on the implement ....................................................................................... 18
2.13.1Position of warning symbols .................................................................................................. 2 4
2.14Dangers in case of non-compliance with the safety instructions ........................................... 25
2.15Safety-conscious working ...................................................................................................... 25
2.16Safety information for users ................................................................................................... 26
2.16.1General safety instructions and accident prevention instructions .......................................... 26
2.16.2Hydraulic system .................................................................................................................... 30
2.16.3Electrical system .................................................................................................................... 31
2.16.4Mounted implements .............................................................................................................. 32
2.16.5Operation of the seed drill ...................................................................................................... 33
2.16.6Cleaning, maintenance and repair ......................................................................................... 34
3Loading and unloading the implement upon delivery ............................ 35
4Product description ................................................................................... 36
4.1Components of the AMAZONE seeding combination ........................................................... 36
4.2Assembly groups of the AD 3000 Super pack top seed drill ................................................. 37
4.3Safety and protective equipment ........................................................................................... 39
4.4Overview – Supply cable / hydraulic hose lines ..................................................................... 40
4.4.1Supply cable........................................................................................................................... 40
4.4.2Identification of the hydraulic hose lines ................................................................................ 40
4.4.3Connection and function of the tractor control units .............................................................. 41
4.5Transportation equipment ...................................................................................................... 42
4.6Proper use .............................................................................................................................. 4 3
4.6.1Approved AMAZONE implement combinations ..................................................................... 44
4.7Danger areas and danger points ........................................................................................... 45
4.8Rating plate and CE mark ...................................................................................................... 46
4.9Technical data ........................................................................................................................ 47
4.10Noise production data ............................................................................................................ 47
4.10.1Technical data for calculating the tractor weight and the tractor axle loads .......................... 48
4.11Tractor equipment .................................................................................................................. 49
4.12Operating pressure of the hydraulic system .......................................................................... 49
5Structure and function .............................................................................. 50
5.1AMAZONE AmaLog+ control terminal ................................................................................... 53
5.2Implement documentation ...................................................................................................... 53
5.3Seed hopper and loading board ............................................................................................ 54
5.3.1Fill level monitoring ................................................................................................................ 54
5.4Rapeseed insert ..................................................................................................................... 55
5.5Seed hopper partition wall ..................................................................................................... 55
6 AD 3000 Super BAH0107-0 02.20
5.6Seeding shaft drive................................................................................................................ 56
5.7Metering ................................................................................................................................ 57
5.7.1Setting values ........................................................................................................................ 58
5.7.2Normal and fine seed metering wheel................................................................................... 60
5.7.3Fine seed metering wheel brushes ....................................................................................... 60
5.7.4Bean seed metering wheel .................................................................................................... 60
5.7.5Bottom flaps .......................................................................................................................... 61
5.7.6Slide gate .............................................................................................................................. 62
5.7.7Agitator shaft support ............................................................................................................ 62
5.7.8Seed rate calibration ............................................................................................................. 63
5.8RoTeC Control coulter .......................................................................................................... 66
5.9Coulter pressure and seed placement depth ........................................................................ 68
5.9.1Coulter pressure adjustment, manually actuated .................................................................. 68
5.9.2Coulter pressure adjustment, hydraulically actuated ............................................................ 69
5.10Exact following harrow .......................................................................................................... 70
5.10.1Exact following harrow tine position ...................................................................................... 71
5.10.2Exact following harrow pressure ........................................................................................... 72
5.11Roller harrow with contour guidance ..................................................................................... 73
5.12Tramlines ............................................................................................................................... 74
5.12.1Tramline control, tabular determination................................................................................. 75
5.12.2Tramline control, graphic determination ................................................................................ 76
5.12.3Functional description ........................................................................................................... 78
5.12.3.1Lay shaft coupling, electrically actuated ............................................................................... 79
5.12.4One-sided switching .............................................................................................................. 80
5.12.5Tramline control 2 and 21 ..................................................................................................... 81
5.13Tramline marker .................................................................................................................... 81
5.14Track marker ......................................................................................................................... 82
6Initial operation .......................................................................................... 83
6.1Checking the suitability of the tractor .................................................................................... 84
6.1.1Calculating the actual values for the total tractor weight, tractor axle loads and tyre
load-bearing capacity, as well as the required minimum ballast weight ............................... 85
6.1.1.1Data required for the calculation (attached implement) ........................................................ 86
6.1.1.2Calculation of the required minimum ballast weight at the front GV min of the tractor
to ensure steering capability ................................................................................................. 87
6.1.1.3Calculation of the actual front axle load of the tractor TV tat ................................................... 87
6.1.1.4Calculation of the actual total weight of the combined tractor and implement ...................... 87
6.1.1.5Calculation of the actual rear axle load of the tractor TH tat ................................................... 87
6.1.1.6Load-bearing capacity of the tractor tyres ............................................................................. 87
6.1.1.7Table ..................................................................................................................................... 88
6.2Secure the tractor / implement against unintentional starting and rolling away ................... 89
7Coupling and uncoupling the implement ................................................ 90
7.1Hydraulic hose lines .............................................................................................................. 92
7.1.1Coupling the hydraulic hose lines ......................................................................................... 92
7.1.2Disconnecting the hydraulic hose lines ................................................................................. 93
7.2Safety instructions for coupling the seed drill ........................................................................ 94
7.2.1Coupling and uncoupling the implement combinations - Overview ...................................... 96
7.2.2Mounting the seed drill on KG/KE/KX 00 soil tillage implements with 1-tube system
roller frame ● Tooth packer roller PW 500 ● Wedge ring roller KW 520 on
KG/KE/KX 01 soil tillage implements with 1-tube system roller frame ● Tooth
packer roller PW 500 ● Wedge ring roller KW 520 ● Simplex prismatic roller SX-45
SG (made by Güttler) ● Simplex prismatic roller SX-45 SU (made by Güttler) .................... 97
7.2.3Uncoupling the seed drill from KG/KE/KX 00 soil tillage implements with 1-tube
system roller frame ● Tooth packer roller PW 500 ● Wedge ring roller KW 520 from
KG/KE/KX 01 soil tillage implements with 1-tube system roller frame ● Tooth
packer roller PW 500 ● Wedge ring roller KW 520 ● Simplex prismatic roller SX-45
SG (made by Güttler) ● Simplex prismatic roller SX-45 SU (made by Güttler) .................. 100
7.2.4Mounting the seed drill on KG/KE/KX 00 soil tillage implements with 2-tube system
roller frames ● Tooth packer roller PW 600 ● Wedge ring roller KW 580 ......................... 103
AD 3000 Super BAH0107-0 02.20 7
7.2.5Uncoupling the seed drill from KG/KE/KX 00 soil tillage implements with 2-tube
system roller frame Tooth packer roller PW 600 Wedge ring roller KW 580 ...................... 108
7.2.6Mounting the seed drill on KG/KE/KX 01 soil tillage implements with 2-tube system
roller frame ● Tooth packer roller PW 600 ● Wedge ring roller KW 580 ● Wedge
ring roller with matrix tyre profile KWM 600 ● Trapeze ring roller TRW 500 ●
Trapeze ring roller TRW 600 ● Simplex prismatic roller SX-50 SG (made by
Güttler) ● Simplex prismatic roller SX-56 SU (made by Güttler) ......................................... 112
7.2.7Uncoupling the seed drill from KG/KE/KX 01 soil tillage implements with 2-tube
system roller frame ● Tooth packer roller PW 600 ● Wedge ring roller KW 580 ●
Wedge ring roller with matrix tyre profile KWM 600 ● Trapeze ring roller TRW 500
● Trapeze ring roller TRW 600 ............................................................................................ 116
7.2.8Uncoupling – Seeding combination from the tractor (all types) ........................................... 120
8Settings ..................................................................................................... 121
8.1Folding the steps up and down ............................................................................................ 122
8.2Moving the star wheel into transport/working position ......................................................... 124
8.2.1Moving the star wheel to the working position ..................................................................... 124
8.2.2Move the star wheel to the transport position ...................................................................... 125
8.3Fill the seed hopper ............................................................................................................. 126
8.4Placing the calibration trays on the funnel rail ..................................................................... 129
8.5Setting the seed rate ............................................................................................................ 130
8.5.1Seeding with the normal or fine seed metering wheel ......................................................... 130
8.5.2Seeding with bean seed metering wheels ........................................................................... 132
8.5.3Adjusting the sliding shutters ............................................................................................... 133
8.5.4Bottom flap position ............................................................................................................. 134
8.5.5Agitator shaft support ........................................................................................................... 135
8.5.6Mounting the rapeseed insert .............................................................................................. 136
8.6Calibrating the seed rate ...................................................................................................... 137
8.6.1Determining the gearbox setting using the calculating disc rule .......................................... 140
8.7RoTeC Control coulter ......................................................................................................... 141
8.7.1Adjusting and checking the seed placement depth ............................................................. 141
8.7.1.1Adjusting the depth control discs / wheels ........................................................................... 142
8.8Coulter pressure .................................................................................................................. 144
8.8.1Coulter pressure adjustment (manual adjustment) .............................................................. 144
8.8.2Hydr. coulter pressureadjustment ........................................................................................ 145
8.9Adjusting the exact following harrow ................................................................................... 146
8.9.1Moving the exact following harrow to the working/transport position .................................. 146
8.9.1.1Move the exact following harrow into working position ........................................................ 146
8.9.1.2Moving the exact following harrow into transport position ................................................... 146
8.9.2Adjusting the exact following harrow tines by rebolting the brackets .................................. 147
8.9.3Infinitely variable adjustment of the exact following harrow tines ........................................ 147
8.9.4Setting the exact following harrow pressure ........................................................................ 148
8.10Adjusting the roller harrow ................................................................................................... 149
8.10.1Setting the pitch of the tines to the ground .......................................................................... 149
8.10.2Working depth adjustment of the harrow tines .................................................................... 149
8.10.3Setting the roller contact pressure ....................................................................................... 150
8.10.4Deactivating/activating the roller harrow .............................................................................. 152
8.10.4.1Deactivating the roller harrow (lifting) .................................................................................. 152
8.10.4.2Activating the roller harrow (lowering) ................................................................................. 153
8.11Activating/deactivating tramline control ............................................................................... 153
8.11.1Activating tramline control .................................................................................................... 153
8.11.2Deactivating tramline control ................................................................................................ 153
8.12Moving the track marker to the working / transport position ................................................ 154
8.13One-sided switching ............................................................................................................. 155
8.13.1Deactivating the left side of the seeding shaft ..................................................................... 155
8.13.2Activating the left side of the seeding shaft ......................................................................... 155
8.14Moving the tramline marker into working/transport position ................................................ 156
8.14.1Move the tramline marker to working position ..................................................................... 156
8.14.2Move the tramline markers to the transport position............................................................ 157
8 AD 3000 Super BAH0107-0 02.20
8.15Moving the exact following harrow road safety bar into road transport/parking
position ................................................................................................................................ 158
8.15.1Moving the road safety bar into road transport position ...................................................... 158
8.15.2Moving the road safety bar into parking position ................................................................ 158
9Transportation ......................................................................................... 159
9.1Moving the seeding combination into transport position ..................................................... 159
9.2Legal regulations and safety ............................................................................................... 160
10Use of the implement .............................................................................. 164
10.1Initial operation .................................................................................................................... 165
10.2Moving the implement from transport into working position ................................................ 165
10.3During operation .................................................................................................................. 166
10.3.1Overview of checks during operation .................................................................................. 166
10.3.2Seeding check ..................................................................................................................... 167
10.4Turning at end of the field ................................................................................................... 168
10.4.1Track marker ....................................................................................................................... 169
10.4.2End of work on the field ....................................................................................................... 169
10.5Emptying the seed hopper and seed housing ..................................................................... 170
11Faults ........................................................................................................ 173
11.1Residual seed quantity display ............................................................................................ 174
11.2Deviations between the set and actual seed rate ............................................................... 174
12Maintenance and repairs ........................................................................ 175
12.1Maintenance schedule ........................................................................................................ 175
12.2Lubrication schedule ........................................................................................................... 176
12.2.1Lubrication points ................................................................................................................ 176
12.3Safety .................................................................................................................................. 177
12.3.1Safety when cleaning the implement .................................................................................. 178
12.3.2Safety when working on the hydraulic system .................................................................... 179
12.4Installations ......................................................................................................................... 180
12.4.1Shutdown of the implement over a long period of time ....................................................... 180
12.4.2Folding down the lay shaft .................................................................................................. 180
12.4.3Folding up the lay shaft ....................................................................................................... 182
12.4.4Setting the tramline spacing, track width and wheelmark width ......................................... 183
12.4.5Installing the bean metering wheels .................................................................................... 185
12.5Maintenance ........................................................................................................................ 188
12.5.1Visual inspection of the upper and lower link pins .............................................................. 188
12.5.2Visual check of the hydraulic hose lines and couplings ...................................................... 189
12.5.2.1Date of manufacture of the hydraulic hose line ................................................................... 189
12.6Checking roller chains and chain wheels ............................................................................ 190
12.6.1Bottom flaps basic position ................................................................................................. 190
12.7Vario gearbox, check the oil level ....................................................................................... 191
12.8Repairs (specialist workshop work) ..................................................................................... 192
12.8.1Checking the hydraulic hose lines ....................................................................................... 192
12.8.1.1Safety when working on hydraulic hose lines ..................................................................... 193
12.9Oils and greases ................................................................................................................. 194
12.9.1Vario gearbox gear oil ......................................................................................................... 194
12.9.2Lubricants for grease nipples and grease guns .................................................................. 194
12.10Bolt tightening torques ........................................................................................................ 195
AD 3000 Super BAH0107-0 02.20 9
User information
10 AD 3000 Super BAH0107-0 02.20
1 User information
The User information section provides information concerning the operating manual.
This operating manual is valid for all versions of the implement.
Figures serve as a reference and are to be understood as representations of the principle.
All of the equipment is described without indicating it as special equipment. A description may be
provided for equipment that is not fitted on the implement or is only available in certain markets. The
sales documents provide information on the equipment of your implement or consult your service
partner for more detailed information.
All information in this operating manual corresponds to the state of knowledge at the time of
publication. Due to ongoing development of the implement, deviations are possible between the
implement and the information in this operating manual. No claims can be made based on differences
in the specifications, figures or descriptions.
If you want to sell the implement, ensure that the operating manual is supplied with the implement.
The operating manual
describes the operation and maintenance of the implement
provides important information on safe and efficient handling of the implement
is an integral part of the implement and should always be kept with the implement or the towing
vehicle
must be kept in a safe place for future use.
Activities to be carried out by the user are presented as numbered instructions. Always observe the
sequence of the instructions. The reaction to instructions is given by an arrow. Example:
1. Instruction 1
Reaction of the implement to handling instruction 1
2. Instruction 2
Listings without a mandatory sequence are presented as a listing with bullets.
Example: Point 1
Point 2
Numbers in round brackets refer to the item numbers in the illustrations. The first number refers to the
diagram and the second number to the item.
Example: (Fig. 3/6) = Figure 3 / Position 6
All the directions specified in the operating manual are always viewed in the direction of travel.
General Safety Instructions
AD 3000 Super BAH0107-0 02.20 11
2 General Safety Instructions
This section contains important information on safe operation of the
implement.
2.1 Obligations and liability
Comply with the instructions in the operating manual
Knowledge of the basic safety information and safety regulations is a
basic requirement for safe handling and fault-free implement
operation.
Obligations of the operator
The operator is obliged only to let those people work with/on the
implement who
are aware of the basic workplace safety information and accident
prevention regulations
have been trained in working with/on the implement
have read and understood this operating manual.
The operator is obliged
to keep all the warning symbols on the implement in a legible
state
to replace damaged warning symbols.
Obligations of the user
Before starting work, anyone charged with working with/on the
machine is obliged
to comply with the basic workplace safety instructions and
accident prevention regulations
to read and understand the "General safety information" section
of this operating manual
to read the section "Warning symbols and other labels on the
implement" in this operating manual and to follow the safety
instructions represented by the warning symbols when operating
the implement
to get to know the implement
to read the sections of this operating manual, important for
carrying out your work.
If the user discovers that a function is not working properly, then they
must eliminate this fault immediately. If this is not the task of the user
or if the user does not have the appropriate technical knowledge, then
they should report this fault to their superior (operator).
General Safety Instructions
12 AD 3000 Super BAH0107-0 02.20
Risks in handling the implement
The implement has been constructed to the state-of-the art and the
recognised rules of safety. However, operating the implement may
cause risks and restrictions
the health and safety of the user or third persons
the implement itself
other property.
Only use the implement
for the purpose for which it was intended
in a perfect state of repair.
Eliminate any faults immediately which could impair safety.
Guarantee and liability
Our "General conditions of sales and delivery" are always applicable.
These shall be available to the operator, at the latest on conclusion of
the contract. Guarantee and liability claims for damage to people or
property will be excluded if they can be traced back to one or more of
the following causes:
Improper use of the implement
Improper installation, commissioning, operation and
maintenance of the implement
Operation of the implement with defective safety equipment or
improperly attached or non-functioning safety and protective
equipment
Non-compliance with the instructions in the operating manual
regarding commissioning, operation and maintenance
Unauthorised design changes to the implement
Insufficient monitoring of implement parts which are subject to
wear
Improperly executed repairs
Disasters due to the effects of foreign objects and force majeure.
General Safety Instructions
AD 3000 Super BAH0107-0 02.20 13
2.2 Representation of safety symbols
Safety instructions are indicated by the triangular safety symbol and the highlighted signal word. The
signal word (DANGER, WARNING, CAUTION) describes the severity of the risk, and carries the
following meaning:
DANGER
Indicates an immediate hazard with high risk, which will result in
death or serious bodily harm (loss of limbs or long-term harm), if
it is not avoided.
If the instructions are not followed, then this will result in
immediate death or serious physical injury.
WARNING
Indicates a medium risk, which could result in death or (serious)
physical injury if not avoided.
If the instructions are not followed, then this may result in death
or serious physical injury.
CAUTION
Indicates a low risk which could cause minor or medium level
physical injury or damage to property if not avoided.
IMPORTANT
Indicates an obligation to special behaviour or an activity
required for proper implement handling.
Non-compliance with these instructions can cause faults on the
implement or disturbance to the environment.
NOTICE
Indicates handling tips and particularly useful information.
These instructions will help you to use all the functions of your
implement in the best way possible.
General Safety Instructions
14 AD 3000 Super BAH0107-0 02.20
2.3 Organisational measures
The operator must provide the necessary personal protective equipment as per the information
provided by the manufacturer of the crop protection agent to be used, such as:
Safety glasses
Protective shoes
Chemical-resistant overalls
Skin protection agents, etc.
The operating manual
must always be kept at the place at which the implement is
operated
must always be easily accessible for the user and maintenance
personnel.
Check all the available safety equipment regularly.
2.4 Safety and protective equipment
Before starting up the implement each time, all the safety and protection equipment must be properly
attached and fully functional. Check all safety and protection equipment regularly.
Faulty safety equipment
Faulty or disassembled safety and protection equipment can lead to dangerous situations.
2.5 Informal safety measures
As well as all the safety information in this operating manual, comply with the general, national
regulations pertaining to accident prevention and environmental protection.
When driving on public roads and routes you should comply with the statutory road traffic regulations.
General Safety Instructions
AD 3000 Super BAH0107-0 02.20 15
2.6 User training
Only those people who have been trained and instructed may work with/on the implement. The
operator must clearly specify the responsibilities of the people charged with operation and
maintenance work.
People being trained may only work with/on the implement under the supervision of an experienced
person.
Person
Activity
Person specially
trained for the
activity 1)
Trained
operator 2)
Persons with
specialist
training
(specialist workshop) 3)
Loading/Transport X X X
Initial operation X
Set-up, tool installation X
operation X
Maintenance X
Troubleshooting and fault
elimination
X X
Disposal X
Key: X..permitted ..not permitted
1) A person who can assume a specific task and who can carry out this task for an appropriately
qualified company.
2) Instructed persons are those who have been instructed in their assigned tasks and in the
possible risks in the case of improper behaviour, have been trained if necessary, and have been
informed about the necessary protective equipment and measures.
3) Persons with specialised technical training shall be considered as a specialist. Due to their
specialist training and their knowledge of the appropriate regulations, they can evaluate the work
with which they have been charged and detect possible dangers.
Comment:
A qualification equivalent to specialist training can be obtained from several years' experience in
the relevant field.
Only a specialist workshop may carry out maintenance and repair
work on the implement, if such work is additionally marked
"Workshop". The personnel of a specialist workshop shall possess the
appropriate knowledge and suitable aids (tools, lifting and support
equipment) for carrying out the maintenance and repair work on the
implement in a way which is both appropriate and safe.
General Safety Instructions
16 AD 3000 Super BAH0107-0 02.20
2.7 Safety measures in normal operation
Only operate the implement if all the safety and protection equipment is fully functional.
Check the implement at least once a day for visible damage and check the function of the safety and
protection equipment.
2.8 Danger from residual energy
Note that there may be residual mechanical, hydraulic, pneumatic and electrical/electronic energy on the
implement.
Use appropriate measures to inform the operator. You can find detailed information in the relevant
sections of this operating manual.
2.9 Maintenance and repair work, fault elimination
Carry out prescribed setting, maintenance and inspection work in good time.
Secure all media such as compressed air and the hydraulic system against unintentional start-up.
Carefully fix and secure larger assembly groups to lifting units when carrying out replacement work.
Check all the bolted connections for tightness. On completion of the maintenance work, check the
function of the safety and protective devices.
2.10 Design changes
You may make no changes, expansions or modifications to the implement without the authorisation of
AMAZONEN-WERKE. This also applies when welding support parts.
Any extension or conversion work shall require the written approval of AMAZONEN-WERKE. Only use
conversion and special equipment parts approved by AMAZONEN-WERKE so that the operating
permit, for example, remains valid in accordance with national and international regulations.
Vehicles with an official type approval or with equipment connected to a vehicle with a valid type
approval or approval for road transport according to the German road traffic regulations must be in the
state specified by the approval.
WARNING
Risk of crushing, cutting, being trapped or drawn in, or impact
through the failure of support parts.
It is strictly forbidden to
drill holes in the frame or on the running gear
increase the size of existing holes on the frame or the running gear
weld on load-bearing parts.
General Safety Instructions
AD 3000 Super BAH0107-0 02.20 17
2.10.1 Spare and wear parts and aids
Immediately replace any implement parts which are not in a perfect state.
Use only genuine AMAZONE spare and wear parts or the parts cleared by AMAZONEN-WERKE so
that the operating permit retains its validity in accordance with national and international regulations. If
you use wear and spare parts from third parties, there is no guarantee that they have been designed
and manufactured in such a way as to meet the requirements placed on them.
AMAZONEN-WERKE shall accept no liability for damage caused by the use of non-approved spare
and wear parts or aids.
2.11 Cleaning and disposal
Handle and dispose of any materials used carefully, in particular
when carrying out work on lubrication systems and equipment and
when cleaning using solvents.
2.12 Workstation of the operator
The implement may be operated by only one person sitting in the driver's seat of the tractor.
General Safety Instructions
18 AD 3000 Super BAH0107-0 02.20
2.13 Warning symbols on the implement
Always keep all the warning symbols of the implement clean and in a
legible state! Replace illegible warning symbols. You can request the
warning symbols from your AMAZONE dealer using the order number
(e.g., MD 075).
Structure
Warning symbols indicate danger areas on the implement and warn against residual dangers. At these
points, there are permanent or unexpected dangers.
A warning symbol consists of two fields.
Field 1
Shows the danger in a triangular safety symbol.
Field 2
Shows instructions for avoiding the danger.
Explanatory text beside the warning symbol
The text beside the warning symbol describes
1. The dangers, e.g.:
Laceration or amputation hazard.
2. The consequence of non-compliance with the risk avoidance instructions, e.g.:
This danger can cause serious injuries to fingers or hands.
3. Instructions for avoiding the risk, e.g.:
Touch machinery parts only when they have come to a complete stop.
General Safety Instructions
AD 3000 Super BAH0107-0 02.20 19
MD 076
Risk of drawing-in/entrapment for hand or arm
due to moving force-transmission parts!
This hazard can cause extremely serious injuries
resulting in the loss of limbs.
Never open or remove protective equipment,
while the tractor engine is running with the
universal joint shaft or hydraulic/electronic
system connected.
if the ground wheel drive is moving.
MD 078
Risk of crushing of fingers/hand by accessible,
moving parts of the implement!
This hazard can cause extremely serious injuries
resulting in the loss of limbs.
Never reach into the danger area when the tractor
engine is running with the universal joint shaft or
hydraulic / electronic system connected.
MD 082
Risk of falling when riding the implement on
treads or platforms!
Causes serious, potentially fatal injuries anywhere on
the body.
It is forbidden to ride on the implement or climb the
implement when it is running. This prohibition also
applies to implements with step surfaces or platforms.
Make sure that nobody is riding on the implement.
General Safety Instructions
20 AD 3000 Super BAH0107-0 02.20
MD 083
Danger of arms being drawn in and/or caught by
moving parts involved in the working process!
This hazard can cause extremely serious injuries
resulting in the loss of limbs.
Never open or remove protective devices while the
tractor engine is running with the universal joint
shaft/hydraulic or electronic systems connected.
MD 089
Risk of crushing the entire body due to standing
under suspended loads or raised implement
parts.
Causes serious, potentially fatal injuries anywhere on
the body.
It is forbidden to stand under suspended loads o
r
raised implement parts.
Maintain an adequate safety distance from any
suspended loads or raised implement parts.
Ensure that all personnel maintain an adequate
safety distance from suspended loads or raised
implement parts.
Table of contents
Other Amazone Farm Equipment manuals
Amazone
Amazone Cenius 4003-2TX User manual
Amazone
Amazone DMC Primera 3000 User manual
Amazone
Amazone Cirrus 03 User manual
Amazone
Amazone Groundkeeper SmartCut GH 1350 User manual
Amazone
Amazone ProfiClick User manual
Amazone
Amazone CatrosXL 4003-2TS User manual
Amazone
Amazone AD-P 3001 Special 850 User manual
Amazone
Amazone TL 251 User manual
Amazone
Amazone GreenDrill GD200-E User manual
Amazone
Amazone Ceus 3000-TX Installation instructions
Amazone
Amazone Avant 4002-2 Installation instructions
Amazone
Amazone GHD 1500 User manual
Amazone
Amazone Catros 5003-2TS Installation instructions
Amazone
Amazone AMASPRAY+ User manual
Amazone
Amazone Tyrok 400 Installation instructions
Amazone
Amazone ZA-M User manual
Amazone
Amazone UX 11201 Super User manual
Amazone
Amazone ZA-M 1800 Ultra Service manual
Amazone
Amazone Cirrus-Control Reference guide
Amazone
Amazone ZG-B-1 User manual
