6.2.3 Coupling the pneumatic brake system 46
6.2.4 Coupling the hydraulic hose lines 47
6.2.5 Coupling the power supply 48
6.2.6 Coupling the tractor's lower link 49
6.2.7 Swivelling up the jack 49
6.2.8 Fastening the safety chain 49
6.2.9 Removing the wheel chocks 50
6.2.10 Releasing the parking brake 51
6.3 Preparing the implement for
operation 51
6.3.1 Preparing the implement for
working without or with the roller 51
6.3.2 Unlocking the tractor control units 55
6.3.3 Removing the road safety bars 55
6.3.4 Preparing the side discs for operation 56
6.3.5 Raising the running gear into
working position 57
6.3.6 Adjusting the working depth of the
discs 57
6.3.7 Adjusting the working depth of the
side discs 58
6.3.8 Adjusting the throughput of the disc
gangs 59
6.3.9 Adjusting the working depth of the
coulters 61
6.3.10 Manual adjustment of the levelling
working depth 63
6.3.11 Preparing the edge levelling discs
for operation 64
6.3.12 Adjusting the scraper to the roller 65
6.3.13 Adjusting the trailing elements 65
6.4 Preparing the machine for road
travel 67
6.4.1 Lowering the running gear into
transport position 67
6.4.2 Preparing the side discs for road
travel 67
6.4.3 Putting on the road safety bars 68
6.4.4 Aligning the implement horizontally 68
6.4.5 Locking the tractor control units 68
7Using the implement 69
7.1 Using the implement 69
7.2 Turning on the headlands 69
8Eliminating faults 70
9Parking the machine 72
9.1 Applying the parking brake 72
9.2 Placing the wheel chocks 72
9.3 Releasing the safety chain 73
9.4 Swivelling down the jack 73
9.5 Uncoupling the tractor's lower link 74
9.6 Uncoupling the pneumatic brake
system 74
9.7 Uncoupling the power supply 74
9.8 Disconnecting the hydraulic
hose lines 75
9.9 Putting on the safety device
against unauthorised use 76
10 Repairing the implement 77
10.1 Maintaining the implement 77
10.1.1 Maintenance schedule 77
10.1.2 Replacing the discs 78
10.1.3 Checking the disc carrier connection 79
10.1.4 Checking the disc carrier rubber O-
rings 80
10.1.5 Aligning the disc gangs relative to
each other 80
10.1.6 Checking the tine fastening with
compression spring overload safety 81
10.1.7 Replacing tines with compression
spring overload safety 81
10.1.8 Replacing C-Mix-3 coulters 82
10.1.9 Replacing the C-Mix-3 Clip coulter 83
10.1.10 Checking the levelling connection 83
10.1.11 Checking the rollers 84
10.1.12 Checking the lower link pins 84
10.1.13 Checking the hydraulic hose lines 84
10.1.14 Checking the wheels 85
10.1.15 Checking the hub bearing 86
10.1.16 Checking the brake pads 86
10.1.17 Checking the pneumatic brake
system 87
MG7242-EN-GB | L.1 | 26.07.2022 | © AMAZONE
II
