Amazone ProfiClick User manual

Operating instructions
AMAz
ProfiClick
Dashboard
to operate the hydraulic functions
MG5668
BAG0138.1
03.15
Printed in Germany
Please read this operating
manual before initial operation.
Keep it in a safe place for future
use!
en

2
Proficlick BAG0138.1
03.15

Identification data
Proficlick
BAG0138.1 03.15
3
Manufacturer's address
AMAZONEN-WERKE
H. DREYER SE & Co. KG
Postfach 51
D-49202
Tel.:
Fax:
E-mail:
Hasbergen, Germany
+ 49 (0) 5405 50 1-0
+ 49 (0) 5405 501-234
[e-mail]
Spare part orders
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Document number:
MG5162
Compilation date:
03.15

Copyright AMAZONEN-WERKE H. DREYER SE & Co. KG, 2014
All rights reserved.
Reprinting, even of sections, only possible with the approval of
AMAZONEN-WERKE H. DREYER SE & Co. KG.

Table of Contents
4
Proficlick BAG0138.1
03.15
1Product description .................................................................................... 5
1.1 Structure.................................................................................................................................. 5
1.2 Function................................................................................................................................... 5
2Operation ..................................................................................................... 6
2.1 Error messages ....................................................................................................................... 8
3Transportation ............................................................................................. 9
4Settings ...................................................................................................... 10
4.1 Teaching in the boom centre position ................................................................................... 10
4.2 Teaching in the centre position for the steering .................................................................... 10
4.3 Adjusting the steering control factor...................................................................................... 11
5Attachment ................................................................................................ 12

Product description
Proficlick
BAG0138.1 03.15
5
1 Product description
1.1 Structure
2 rocker switches
Latching in 2 positions
Rotary knob
+/ - 135°
4 rocker switches, momentary
With latching centre position
Rotary knob
+/ - 135°
Press the momentary rocker switch until the end position / desired
position (boom height) has been reached.
After switching on, the rotary knobs must be turned once to the centre
position before they are functional.
1.2 Function
The ProfiClick control device serves to operate the hydraulic functions
of an Amazone field sprayer.
To do so, the field sprayer must be equipped accordingly.
During operation, the field sprayer is constantly supplied with hydrau-
lic fluid through an oil circuit.
The ProfiClick is available in versions with or without steering func-
tion.

Operation
6
Proficlick BAG0138.1
03.15
2 Operation
ProfiClick main switch
Latching rocker switch
0 ProfiClick switched off
1ProfiClick switched on
AutoTrail (optional)
Latching rocker switch
Steering in automatic mode (precise
tracking of the implement)
•The steering angle is constantly regulated
in the defined target position.
•When the steering rotary knob is in centre
position, the target position of the steering
angle is the same as the taught-in centre
position.
Steering in manual mode
Rotary knob for manual steering of the
field sprayer.
→The light shows the centre position of the
steering in manual mode.
In automatic mode: The intensity of the slope
correction can be adjusted using the rotary knob.
In manual mode: Rotary knob for direct steering
against the slope.
The rotary knobs only react when they were
turned to the centre position once after switching
on.
If the boom is locked when the steering is in
automatic mode, a warning tone is issued
οuntil the boom is unlocked,
ο
until the steering is switched to manual
mode.

Operation
Proficlick
BAG0138.1 03.15
7
Boom locking mechanism
Momentary rocker switch
Boom unlocked during operation
Boom locked for folding and for one-sided
spraying.
→Actuate the rocker switch for approx. 8 sec-
onds.
Fold the left boom section
Momentary rocker switch
Unfold the left boom section
Fold the left boom section
Fold the right boom section
Momentary rocker switch
Unfold the right boom section
Fold the right boom section
To move the sprayer boom into working position and transport posi-
tion, please also refer to the implement operating manual.
To fold both boom sections at the same time, actuate both rocker
switches simultaneously until the end position is reached.

Operation
8
Proficlick BAG0138.1
03.15
Boom height and tilt
Momentary rocker switch
Raise the boom
Lower the boom
Rotary knob to adjust the boom tilt.
The rotary knobs only react when they were
turned to the centre position once after switching
on.
DANGER
Risk of accident due to unintentional operation of the hydraulic
functions while driving on the road.
When driving on road, interrupt the oil circulation and switch the Pro-
fiClick off.
2.1 Error messages
If an error is detected by the sensors, none of the ProfiClick functions
should be executed. However, the rotary knobs can be operated.
As long as the error persists, it is displayed by:
•a recurrent acoustic signal,
•flashing light on the main switch.

Transportation
Proficlick
BAG0138.1 03.15
9
3 Transportation
DANGER
Risk of accident caused by turning the machine over !
For road transport, set the steering axle / steering drawbar to
transport position!
1. Set the steering drawbar / steering axle to
the middle position (steering drawbar /
wheels align with machine).
For this:
1.1 Put AutoTrail in manual
operation.
1.2 Move to the middle position.
1.3 Move the machine until the centre po-
sition is reached.
2. Switch off the red tractor control unit.
3. Secure the steering drawbar (1) by closing
the stop tap (3) in position 0.

Settings
10
Proficlick BAG0138.1
03.15
4 Settings
4.1 Teaching in the boom centre position
When the rotary knob is in centre position (ma
rk positioned vertically),
the unfolded sprayer boom must be aligned horizontally.
Otherwise, teach in the centre position.
1. Align the sprayer boom horizontally.
2. Switch off the main switch.
3. Press down the right-
hand rocker switch for
folding and
the rocker switch for the boom
height.
4. At the same time, switch on the main
switch.
→An acoustic signal is issued and the centre
position is saved.
4.2 Teaching in the centre position for the steering
When the rotary knob is in centre position (mark positioned vertically),
the steering must be in neutral position (axle / drawbar aligned in the
direction of travel).
Otherwise, teach in the centre position.
1. Move the steering into neutral position
(axle / drawbar are aligned in the direction
of travel).
2. Switch off the main switch.
3. Press down the left-hand rocker switch for
folding and
the rocker switch for the boom locking
mechanism.
4. At the same time, switch on the main
switch.
→An acoustic signal is issued and the centre
position is saved.

Settings
Proficlick
BAG0138.1 03.15
11
4.3 Adjusting the steering control factor
Only with steered axle!
Default value 1.25 (cannot be read off)
1. Put the steering into .
2. Switch off ProfiClick.
3. Put the boom locking mechanism on
and simultaneously
on
4. Switch on ProfiClick.
→Two beeps indicate that the calibration
menu is active.
→Light for the centre position is flashing.
Do not execute any hydraulic functions while
making the adjustments.
5. Adjust the control factor using the boom
locking mechanism
•Each time the rocker switch is pressed up-
wards, the control factor is increased by
0.05.
•Each time the rocker switch is pressed
downwards, the control factor is reduced by
0.05.
•When all four rocker switches are pressed
downwards, the control factor is restored to
the default value of 1.25.
The calibration menu closes automatically.
6. Exit the calibration menu: Move the
steering to .
→Two beeps indicate that the calibration
menu is exited.

Attachment
12
Proficlick BAG0138.1
03.15
5 Attachment
•Install the bracket within easy reach in the
tractor cab.
•
Attach the ProfiClick using the tube sleeves.
•Adjust the angle using the wing nuts.
•Couple the implement wiring harness with
the 23-pin plug on the ProfiClick.
•Connect the power supply cable to a 12V
connection.

Proficlick
BAG0138.1 03.15
13