Amazone Cirrus 03 User manual
Operating Manual
az
Large area seed drill
Cirrus 03
MG6382
BAH0101-05 11.19
Please read this
operating manual
before initial operation.
Keep it in a safe place for future use!
en
2 Cirrus 03 BAH0101-05 11.19
Reading the instruction
manual and to adhere to it should not appear to
be inconvenient and superfluous as it is not
enough to hear from others and to realise that a
machine is good, to buy it and to believe that now
everything would work by itself. The person
concerned would not only harm himself but also
make the mistake of blaming the machine for the
reason of a possible failure instead of himself. In
order to ensure a good success, one must consider
the design of the object, in other words one must
make himself familiar with every aspect of the
machine and gain practice in handling the
machine. Only by doing so would you be satisfie
d
both with the machine and also with yourself. To
achieve this is the purpose of this instruction
manual.
Leipzig-Plagwitz 1872.
Cirrus 03 BAH0101-05 11.19 3
Identification data
Please insert the identification data of the implement. The identification
data are arranged on the rating plate.
Implement number (ten digits):
Type:
Year of manufacture:
Basic weight (kg):
Permissible total weight (kg):
Manufacturer address
AMAZONEN-WERKE
H. Dreyer GmbH & Co. KG
Postfach 51
D-49202
Tel.:
E-mail:
Hasbergen, Germany
+ 49 (0) 5405 50 1-0
Spare Parts Order
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Type: Cirrus 03
Document number: MG6382
Compilation date: 11.19
Copyright AMAZONEN-WERKE H. Dreyer GmbH & Co. KG, 2019
All rights reserved.
Reprinting, even of sections, only possible with the approval of
AMAZONEN-WERKE H. Dreyer GmbH & Co. KG.
4 Cirrus 03 BAH0101-05 11.19
Foreword
Dear Customer,
You have chosen one of the quality products from the wide product range of AMAZONEN-WERKE,
H. Dreyer GmbH & Co. KG. We thank you for your trust in our products.
On receiving the implement, check to see if it has been damaged during transport or if parts are
missing. Using the delivery note, check that the implement has been delivered in full, including any
special equipment ordered. Damage can only be rectified if problems are claimed immediately.
Before initial operation, read and comply with the information in this operating manual, and particularly
the safety instructions. Only after careful reading will you be able to benefit from the full scope of your
newly purchased implement.
Please ensure that all the implement operators have read this operating manual before they put the
implement into operation.
Should you have any questions or problems, please consult this operating manual or contact your
local service partner.
Regular maintenance and timely replacement of worn or damaged parts increases the service life of
your implement.
Cirrus 03 BAH0101-05 11.19 5
1User information ........................................................................................ 13
2General Safety Instructions ...................................................................... 14
2.1Obligations and liability .......................................................................................................... 14
2.2Representation of safety symbols .......................................................................................... 16
2.3Organisational measures ....................................................................................................... 17
2.4Safety and protective equipment ........................................................................................... 17
2.5Informal safety measures ....................................................................................................... 17
2.6User training ........................................................................................................................... 18
2.7Safety measures in normal operation .................................................................................... 19
2.8Danger from residual energy ................................................................................................. 19
2.9Maintenance and repair work, fault elimination ..................................................................... 19
2.10Design changes ..................................................................................................................... 20
2.10.1Spare and wear parts and aids .............................................................................................. 21
2.11Cleaning and disposal ............................................................................................................ 21
2.12Workstation of the operator .................................................................................................... 21
2.13Warning symbols and other labels on the implement ............................................................ 22
2.13.1Position of warning symbols .................................................................................................. 2 9
2.14Dangers in case of non-compliance with the safety instructions ........................................... 31
2.15Safety-conscious working ...................................................................................................... 31
2.16Safety information for users ................................................................................................... 32
2.16.1General safety instructions and accident prevention instructions .......................................... 32
2.16.2Hydraulic system .................................................................................................................... 36
2.16.3Electrical system .................................................................................................................... 37
2.16.4Attached implements ............................................................................................................. 37
2.16.5Brake system ......................................................................................................................... 38
2.16.6Tyre ........................................................................................................................................ 39
2.16.7Operation of the seed drill ...................................................................................................... 39
2.16.8PTO shaft operation ............................................................................................................... 40
2.16.9Cleaning, maintenance and repair ......................................................................................... 41
3Loading and unloading the low-bed trailer for delivery ......................... 42
3.1Preparing the implement for loading and unloading .............................................................. 42
3.2Loading the flat-bed trailer ..................................................................................................... 44
3.3Unloading the implement ....................................................................................................... 45
4Product description ................................................................................... 47
4.1Main assembly groups of the implement ............................................................................... 49
4.1.1Overview of assembly groups ................................................................................................ 50
4.2Safety and protective equipment ........................................................................................... 54
4.3Overview – Supply lines between the tractor and the implement .......................................... 55
4.4Transportation equipment ...................................................................................................... 58
4.5Safety device against unauthorised use ................................................................................ 59
4.6Proper use .............................................................................................................................. 6 0
4.7Danger areas and danger points ........................................................................................... 61
4.8Rating plate and CE mark ...................................................................................................... 62
4.9Technical data ........................................................................................................................ 64
4.9.1Road transport data ............................................................................................................... 66
4.10Required tractor equipment ................................................................................................... 6 7
4.11Noise production data ............................................................................................................ 67
5Structure and function .............................................................................. 68
5.1Control terminal for implements with ISOBUS system .......................................................... 69
5.1.1AMAZONE AmaTron 4 control terminal ................................................................................. 69
5.1.2AMAZONE TwinTerminal ....................................................................................................... 70
5.2Controlling the implement with the control terminal ............................................................... 70
6 Cirrus 03 BAH0101-05 11.19
5.3Brake system ......................................................................................................................... 71
5.3.1Parking brake ........................................................................................................................ 71
5.3.2Dual-circuit pneumatic braking system ................................................................................. 72
5.3.3Hydraulic brake system ......................................................................................................... 72
5.4Implements without their own brake system ......................................................................... 72
5.5Stowage compartment .......................................................................................................... 73
5.6Radar ..................................................................................................................................... 73
5.7Tractor wheel mark eradicator .............................................................................................. 74
5.8Crushboard ............................................................................................................................ 75
5.9Two row disc array ................................................................................................................ 76
5.10minimum TillDisc disc array .................................................................................................. 78
5.11T-Pack ................................................................................................................................... 79
5.11.1T-Pack IN .............................................................................................................................. 79
5.11.2T-Pack S ................................................................................................................................ 79
5.11.3T-Pack U ............................................................................................................................... 80
5.12Trailing roller with integrated running gear ............................................................................ 81
5.12.1Tyre designations .................................................................................................................. 82
5.12.2Furrow ridge leveller .............................................................................................................. 83
5.12.2.1Furrow ridge levellers - For implements with RoTeC pro Control coulters ........................... 83
5.12.2.2Furrow ridge levellers - For implements with TwinTeC+ double disc coulters ...................... 83
5.13Hopper ................................................................................................................................... 84
5.13.1One chamber hopper ............................................................................................................ 84
5.13.2Two chamber hopper ............................................................................................................ 84
5.13.3Monitoring the hopper content .............................................................................................. 86
5.13.4Filling auger ........................................................................................................................... 86
5.14Conveyor section ................................................................................................................... 87
5.14.1Seed drills with one metering unit and one distributor head ................................................. 87
5.14.2Seed drills with one metering unit and two distributor heads ................................................ 88
5.14.3Seed drills with two metering units and one distributor head ................................................ 88
5.14.4Cirrus (-C)(-2C) with two metering units and two distributor heads ...................................... 89
5.14.5Cirrus (-CC)(-2CC) with two metering units and two distributor heads ................................. 90
5.15Metering ................................................................................................................................ 91
5.15.1Metering roller table - Figures ............................................................................................... 93
5.15.2Table – metering rollers, seed ............................................................................................... 96
5.15.3Table – Fertiliser metering rollers .......................................................................................... 97
5.15.4Calibrating the spread rate .................................................................................................... 98
5.15.5Calibration – One-chamber system ....................................................................................... 99
5.15.6Calibration – Two-chamber system ..................................................................................... 100
5.15.6.1Metering operation - Two-chamber system during operation ............................................. 101
5.15.7Spreading seed with wide row spacing ............................................................................... 101
5.16Fan ...................................................................................................................................... 102
5.16.1Fan speeds - One-chamber system .................................................................................... 103
5.16.2Fan speeds - Two-chamber system .................................................................................... 104
5.16.3Connecting the blower fan to the tractor hydraulics ............................................................ 105
5.16.4Blower fan connection to the tractor PTO shaft (on-board hydraulic system) .................... 106
5.17Distributor head ................................................................................................................... 107
5.17.1Seed tube monitoring .......................................................................................................... 108
5.18RoTeC pro Control coulter .................................................................................................. 109
5.18.1Coulter pressure adjustment ............................................................................................... 111
5.18.2Seed rate increase .............................................................................................................. 111
5.19TwinTeC+ double disc coulter ............................................................................................. 112
5.19.1Seed placement depth range .............................................................................................. 113
5.19.2Seed placement depth ........................................................................................................ 113
5.19.3Coulter pressure .................................................................................................................. 114
5.19.3.1Coulter pressure - Manual actuation ................................................................................... 114
5.19.3.2Coulter pressure - Actuation on the control terminal ........................................................... 114
5.20FerTeC single-disc coulter .................................................................................................. 115
5.21Exact following harrow ........................................................................................................ 116
5.21.1Exact following harrow tine position .................................................................................... 117
Cirrus 03 BAH0101-05 11.19 7
5.21.2Exact following harrow pressure adjustment ....................................................................... 117
5.22Roller harrow ........................................................................................................................ 118
5.23Track marker ........................................................................................................................ 120
5.24Seeding variations adjustable on the control terminal ......................................................... 121
5.24.1Adapting the seeding rate to the acceleration of the tractor ................................................ 121
5.24.2Seeding a corner on the field ............................................................................................... 121
5.25Tramlines ............................................................................................................................. 122
5.25.1Tramline rhythm, tabular determination ............................................................................... 123
5.25.2Tramline rhythm, graphic determination .............................................................................. 130
5.25.3Track width / wheelmark width of the cultivating tractor ...................................................... 132
5.25.4One-sided switching ............................................................................................................. 133
5.25.4.1One-sided switching, mechanically adjustable for implements with 1 distributor
head ..................................................................................................................................... 134
5.25.4.2One-sided switching, electrically adjustable for implements with 1 distributor head
with max. 32 connections ..................................................................................................... 134
5.25.4.3One-sided switching with two distributor heads, except Cirrus (-CC) .................................. 135
5.25.5Double tramline control for implements with 6 m working width .......................................... 138
5.26Tramline marker ................................................................................................................... 139
5.27Work floodlights ................................................................................................................... 140
5.28Camera system .................................................................................................................... 140
5.29Catch crop seed drill GreenDrill ........................................................................................... 141
6Initial operation ........................................................................................ 142
6.1Checking the suitability of the tractor ................................................................................... 143
6.1.1Calculating the actual values for the total tractor weight, tractor axle loads and tyre
load-bearing capacity, as well as the required minimum ballast weight .............................. 144
6.1.1.1Data required for the calculation (hitched implement) ......................................................... 145
6.1.1.2Calculation of the required minimum ballast weight at the front GV min of the tractor
to ensure steering capability ................................................................................................ 146
6.1.1.3Calculation of the actual front axle load of the tractor TV tat ................................................. 146
6.1.1.4Calculation of the actual total weight of the combined tractor and implement .................... 146
6.1.1.5Calculation of the actual rear axle load of the tractor TH tat .................................................. 146
6.1.1.6Load-bearing capacity of the tractor tyres ........................................................................... 146
6.1.1.7Table .................................................................................................................................... 147
6.1.2Requirements for tractor operation with trailed implements ................................................ 148
6.2Secure the tractor / implement against unintentional starting and rolling away .................. 149
6.3Fan drive - Hydraulic connection ......................................................................................... 151
7Coupling and uncoupling the implement .............................................. 152
7.1Dual-circuit pneumatic braking system ................................................................................ 154
7.1.1Coupling the brake and supply lines .................................................................................... 156
7.1.2Uncoupling the supply and brake line .................................................................................. 158
7.1.3Control elements for the dual-circuit pneumatic braking system ......................................... 159
7.1.4Position of the brake load adjustment lever for the dual air circuit service brake
system .................................................................................................................................. 160
7.2Hydraulic brake system ........................................................................................................ 161
7.2.1Coupling the hydraulic brake system ................................................................................... 161
7.2.2Uncoupling the hydraulic brake system ............................................................................... 163
7.3Hydraulic hose lines ............................................................................................................. 165
7.3.1Coupling the hydraulic hose lines ........................................................................................ 165
7.3.2Uncoupling the hydraulic hose lines .................................................................................... 166
7.4Coupling the implement to the tractor .................................................................................. 167
7.4.1Coupling the T-Pack U ......................................................................................................... 169
7.4.2Coupling the Cirrus to the tractor ......................................................................................... 169
7.5Uncoupling the implement ................................................................................................... 173
7.6Connect/disconnect the PTO shaft driven hydraulic pump .................................................. 176
7.6.1Connecting the hydraulic pump ........................................................................................... 177
7.6.2Uncoupling the hydraulic pump............................................................................................ 177
8Settings ..................................................................................................... 178
8 Cirrus 03 BAH0101-05 11.19
8.1Securing the light carriers (only on folding implements) ..................................................... 178
8.2Moving the tractor wheel mark eradicator into working and transport position ................... 179
8.2.1Moving the tractor wheel mark eradicator into working position ......................................... 179
8.2.2Moving the tractor wheel mark eradicator into transport position ....................................... 179
8.3Crushboard working depth adjustment ............................................................................... 180
8.4Disc array ............................................................................................................................ 181
8.4.1Setting the working depth .................................................................................................... 181
8.4.2Adjustment of individual discs ............................................................................................. 181
8.4.3Setting the side panels ........................................................................................................ 182
8.5Cutting disc array ................................................................................................................ 183
8.5.1Setting the working depth .................................................................................................... 183
8.5.2Adjustment of individual discs ............................................................................................. 183
8.6Repositioning the low level sensor ...................................................................................... 184
8.7Installing/removing the metering roller ................................................................................ 184
8.8Calibrating the spread rate .................................................................................................. 188
8.8.1Calibration methods - Overview .......................................................................................... 188
8.8.2Calibration - Seed drills with one metering unit and one distributor head........................... 189
8.8.3Calibration - Seed drills with 1 metering unit and 2 distributor heads ................................. 190
8.8.4Calibration - Seed drills with two metering units and one distributor head ......................... 192
8.8.5Calibration - Cirrus (-C)(-2C) with two metering units and two distributor heads................ 193
8.8.6Calibration - Cirrus (-CC)(-2CC) with two metering units and two distributor heads .......... 195
8.8.6.1Calibrating metering unit 1 .................................................................................................. 195
8.8.6.2Calibrating metering unit 2 .................................................................................................. 196
8.8.6.3Admixtures .......................................................................................................................... 197
8.9Adjusting the fan speed ....................................................................................................... 198
8.9.1Setting the fan speed - On the flow control valve of the tractor .......................................... 199
8.9.2Setting the fan speed - Tractors without flow control valve ................................................ 199
8.9.3Setting the fan speed - Connection to the tractor PTO shaft .............................................. 199
8.9.4Pressure relief valve with round outer contour .................................................................... 200
8.9.4.1Basic setting of the pressure relief valve ............................................................................ 200
8.9.4.2Blower fan speed setting ..................................................................................................... 200
8.9.5Pressure relief valve with hexagonal outer contour ............................................................ 201
8.9.5.1Basic setting of the pressure relief valve ............................................................................ 201
8.9.5.2Blower fan speed setting ..................................................................................................... 201
8.9.6Fan speed monitoring ......................................................................................................... 202
8.9.7Pressure monitoring in the two chamber hopper ................................................................ 202
8.10RoTeC pro Control coulter .................................................................................................. 203
8.10.1Adjusting and checking the seed placement depth ............................................................. 203
8.10.1.1Adjusting the depth control discs/wheels ............................................................................ 204
8.10.2Setting the coulter pressure ................................................................................................ 206
8.10.3Adjusting the automatic seed rate increase ........................................................................ 206
8.11TwinTeC+ double disc coulter ............................................................................................. 207
8.11.1Adjusting and checking the seed placement depth ............................................................. 207
8.11.2Adjusting the placement depth range.................................................................................. 207
8.11.3Adjusting the placement depth ............................................................................................ 208
8.11.4Setting the coulter pressure ................................................................................................ 210
8.11.4.1Setting the coulter pressure with the knurled screw ........................................................... 210
8.11.4.2Gradually adjusting the coulter pressure on the control terminal ........................................ 210
8.11.5Adjusting the harrow tines ................................................................................................... 211
8.11.5.1Adjusting the pitch of the harrow tines ................................................................................ 211
8.11.5.2Harrow tine working depth adjustment ................................................................................ 212
8.11.5.3Putting the harrow tines into parking position ..................................................................... 213
8.12Adjusting the furrow ridge levellers ..................................................................................... 214
8.12.1Furrow ridge levellers - Adjustment at the centre of the implement .................................... 214
8.12.2Furrow ridge levellers - Section adjustments ...................................................................... 214
8.13FerTeC single-disc coulter .................................................................................................. 215
8.13.1Adjusting the placement depth ............................................................................................ 215
8.14Exact following harrow ........................................................................................................ 216
8.14.1Moving the exact following harrow to the working / transport position ................................ 216
8.14.2Exact following harrow tine position .................................................................................... 217
Cirrus 03 BAH0101-05 11.19 9
8.14.3Exact following harrow pressure adjustment ....................................................................... 217
8.15Roller harrow ........................................................................................................................ 218
8.15.1Adjusting and testing the roller pressure ............................................................................. 218
8.15.2Adjusting the tilt of the harrow tines ..................................................................................... 219
8.15.3Adjusting the working depth of the harrow tines .................................................................. 220
8.16Track marker ........................................................................................................................ 221
8.16.1Track marker transport lock (rigid implements only) ........................................................... 222
8.17Activating the one-sided switching ....................................................................................... 223
8.17.1One-sided switching with one distributor head .................................................................... 223
8.17.1.1One-sided switching with one distributor head - Installing an insert .................................... 223
8.17.1.2One-sided switching, electronically adjustable for implements with 1 distributor
head with max. 32 connections............................................................................................ 224
8.17.2One-sided switching with two distributor heads ................................................................... 225
8.18Adjusting the tramline marker .............................................................................................. 226
8.18.1Moving the tramline marker into working position ................................................................ 226
8.18.2Moving the tramline marker into transport position .............................................................. 227
8.18.3Adjusting the track discs to the tractor track width............................................................... 228
8.18.4Tramline marker – Track discs rotated by 180° ................................................................... 230
8.18.5Moving the double tramline marker into working / transport position .................................. 231
8.19Moving the road safety bar into transport/parking position .................................................. 233
8.19.1Moving the road safety bar to transport position.................................................................. 233
8.19.2Moving the road safety bar into parking position ................................................................. 233
9Transportation ......................................................................................... 234
9.1Moving the implement into road transport position .............................................................. 234
9.2Legal regulations and safety ................................................................................................ 235
9.3Safety during road transport ................................................................................................ 237
10Use of the implement ............................................................................... 240
10.1Initial operation ..................................................................................................................... 242
10.2Moving the implement into working position ........................................................................ 243
10.3Unfolding/folding the implement booms ............................................................................... 244
10.3.1Unfolding the implement sections ........................................................................................ 245
10.3.2Folding the implement sections ........................................................................................... 246
10.4Filling the hopper ................................................................................................................. 250
10.4.1Opening/closing the roller tarpaulin ..................................................................................... 252
10.4.2Opening/closing the hopper cover ....................................................................................... 254
10.4.3Filling auger for rigid implements ......................................................................................... 258
10.4.3.1Move the filling auger into the filling position ....................................................................... 258
10.4.3.2Residual emptying of the filling auger .................................................................................. 261
10.4.3.3Moving the filling auger into transport position .................................................................... 262
10.4.4Filling auger for folding implements ..................................................................................... 264
10.4.4.1Move the filling auger into the filling position ....................................................................... 264
10.4.4.2Using the filling auger to fill the hopper ................................................................................ 267
10.4.4.3Residual emptying of the filling auger .................................................................................. 269
10.4.4.4Moving the filling auger into transport position .................................................................... 269
10.5During operation .................................................................................................................. 271
10.5.1Check points ........................................................................................................................ 271
10.5.1.1Checking the placement depth of the seed and the fertiliser ............................................... 272
10.5.2Turning at end of the field .................................................................................................... 272
10.6End of work on the field ....................................................................................................... 273
10.7Emptying the hopper and/or the metering unit ..................................................................... 274
10.7.1One chamber hopper quick emptying .................................................................................. 274
10.7.2Two chamber hopper quick emptying .................................................................................. 275
10.7.3Hopper residual emptying .................................................................................................... 276
10.7.4Emptying the metering unit .................................................................................................. 276
11Faults ........................................................................................................ 277
11.1Residual seed volume indicator ........................................................................................... 277
11.2Deviations between the preset and actual seeding rates .................................................... 278
10 Cirrus 03 BAH0101-05 11.19
11.3Failure of the control terminal during operation .................................................................. 279
11.4Fault table ............................................................................................................................ 281
12Cleaning, maintenance and repairs ....................................................... 282
12.1Safety .................................................................................................................................. 282
12.1.1Safety of the implement coupled ......................................................................................... 284
12.1.2Safety when attaching or removing special equipment....................................................... 284
12.1.3Safety when working on hydraulic hose lines ..................................................................... 285
12.1.3.1Safety through labelling the hydraulic hose lines ................................................................ 286
12.2Safety when cleaning the implement .................................................................................. 287
12.2.1Safety when working on the distributor head ...................................................................... 289
12.3Cleaning the implement ...................................................................................................... 289
12.3.1Cleaning the fan suction guard screen................................................................................ 289
12.3.2Cleaning the blower fan ...................................................................................................... 289
12.3.3Clean the distributor head ................................................................................................... 290
12.3.4Clean the oil cooler.............................................................................................................. 290
12.3.5Cleaning the hopper ............................................................................................................ 291
12.4Lubrication schedule ........................................................................................................... 293
12.4.1Lubrication points ................................................................................................................ 294
12.5Maintenance schedule ........................................................................................................ 298
12.6Adjustment and maintenance work ..................................................................................... 301
12.6.1Mount the plugs in the distributor head for spreading seed with wide row spacing ........... 301
12.6.2Checking the tensioned crosspiece when coupling the implement .................................... 302
12.6.3Checking the tensioned crosspiece and drawbar ............................................................... 302
12.6.4Check the drawbar tightening torques ................................................................................ 302
12.6.5Check the transport locking mechanism of the implement booms ..................................... 303
12.6.6Tyre inflation pressure and wheel nut tightening torque ..................................................... 304
12.6.6.1Roller with integrated running gear ..................................................................................... 304
12.6.6.2T-Pack IN ............................................................................................................................ 306
12.6.6.3T-Pack S .............................................................................................................................. 306
12.6.6.4T-Pack U ............................................................................................................................. 306
12.6.7On-board hydraulics – Oil check and oil filter change ......................................................... 307
12.6.8Parking the implement for a longer period of time .............................................................. 309
12.7Work to be performed in a specialist workshop .................................................................. 310
12.7.1Checking the hydraulic hose lines ....................................................................................... 310
12.7.2Drawbar pipe length adjustment ......................................................................................... 312
12.7.3Check and replace the spring element bearing .................................................................. 315
12.7.4Coulter body adjustment - FerTeC single-disc coulter ........................................................ 316
12.7.5Adjust the furrow ridge levellers - Implements with RoTeC pro control coulters ................ 316
12.7.6Adjusting the tramlines on the distributor head ................................................................... 317
12.7.6.1Adjusting the tramline track width on the distributor head .................................................. 318
12.7.6.2Adjusting the tramline wheelmark width on the distributor head ......................................... 318
12.7.6.3Removing and installing the segment in the distributor head ............................................. 319
12.7.6.4Electrical connection of the tramline segments ................................................................... 320
12.7.6.5Deactivating tramline segments .......................................................................................... 321
12.7.7Check and replace the disc array discs .............................................................................. 322
12.7.8Replacing the grid on the RoTeC pro Control coulter ......................................................... 323
12.7.9Checking and readjusting the TwinTeC+ disc bearings ...................................................... 324
12.7.9.1Checking the TwinTeC disc bearing ................................................................................... 324
12.7.9.2Readjusting the TwinTeC disc bearings ............................................................................. 324
12.7.10Dismounting the TwinTeC+ seed line ................................................................................. 326
12.7.11Checking / replacing the TwinTeC+ inner scraper .............................................................. 326
12.7.12Checking / replacing the TwinTeC+ seed catcher .............................................................. 327
12.7.13Checking / replacing the TwinTeC+ baffle lip ...................................................................... 328
12.7.14Checking / replacing the TwinTeC+ press roller ................................................................. 329
12.7.15Checking / readjusting / replacing the TwinTeC+ roller scraper ......................................... 329
12.7.16Check / set swivel arm filling auger Cirrus 4/6003-2 ........................................................... 330
12.7.17Exchanging the exact following harrow and the roller harrow with each other ................... 331
12.7.17.1Preparing the roller harrow .................................................................................................. 331
12.7.17.2Preparing the exact following harrow .................................................................................. 332
12.7.17.3Exchanging the exact following harrow with the roller harrow ............................................ 333
Cirrus 03 BAH0101-05 11.19 11
12.7.18Repairs on the pressure hopper .......................................................................................... 335
12.8Brake system (all versions) .................................................................................................. 336
12.8.1General visual inspection of the brake system .................................................................... 336
12.8.2General functional check of the brake system ..................................................................... 337
12.8.3Cleaning the brake drums .................................................................................................... 337
12.8.4Checking the brake system for safe operating condition at a specialist workshop ............. 338
12.9Dual-circuit pneumatic braking system ................................................................................ 338
12.9.1Exterior inspection of the compressed air tank every 3 months .......................................... 338
12.9.2Check the pressure in the compressed air tank .................................................................. 338
12.9.3Leak test ............................................................................................................................... 339
12.9.4Cleaning the line filter .......................................................................................................... 339
12.10Bolt tightening torques ......................................................................................................... 340
13Hydraulic diagram .................................................................................... 342
13.1Hydraulic diagram - Cirrus 3003/3503 Compact / RoTeC pro ............................................. 342
13.2Hydraulic diagram - Cirrus 3003 Compact / TwinTeC+ ....................................................... 344
13.3Hydraulic diagram - Cirrus 3503 Compact / RoTeC pro ...................................................... 346
13.4Hydraulic diagram Cirrus 4003 (-C)(-CC) / RoTeC pro........................................................ 348
13.5Hydraulic diagram - Cirrus 4003-2(C)(CC) / RoTeC pro, part 1 .......................................... 350
13.5.1Hydraulic diagram - Cirrus 4003-2(C)(CC) / RoTeC pro, part 2 .......................................... 352
13.6Hydraulic diagram - Cirrus 4003-2(C)(CC) / TwinTeC+, part 1 ........................................... 354
13.6.1Hydraulic diagram - Cirrus 4003-2(C)(CC) / TwinTeC+, part 2 ........................................... 356
13.7Hydraulic diagram - Cirrus 6003-2(C)(CC) / RoTeC pro, part 1 .......................................... 358
13.7.1Hydraulic diagram - Cirrus 6003-2(C)(CC) / RoTeC pro, part 2 .......................................... 360
13.8Hydraulic diagram - Cirrus 6003-2(C)(CC) / TwinTeC+, part 1 ........................................... 362
13.8.1Hydraulic diagram - Cirrus 6003-2(C)(CC) / TwinTeC+, part 2 ........................................... 364
12 Cirrus 03 BAH0101-05 11.19
User information
Cirrus 03 BAH0101-05 11.19 13
1 User information
The User information section provides information concerning the operating manual.
This operating manual is valid for all versions of the implement.
Figures serve as a reference and are to be understood as representations of the principle.
All of the equipment is described without indicating it as special equipment. A description may be pro-
vided for equipment that is not fitted on the implement or is only available in certain markets. The sales
documents provide information on the equipment of your implement or consult your service partner for
more detailed information.
All information in this operating manual corresponds to the state of knowledge at the time of publica-
tion. Due to ongoing development of the implement, deviations are possible between the implement
and the information in this operating manual. No claims can be made based on differences in the
specifications, figures or descriptions.
If you want to sell the implement, ensure that the operating manual is supplied with the implement.
The operating manual
describes the operation and maintenance of the implement
provides important information on safe and efficient handling of the implement
is an integral part of the implement and should always be kept with the implement or the towing
vehicle
must be kept in a safe place for future use.
Activities to be carried out by the user are presented as numbered instructions. Always observe the
sequence of the instructions. The reaction to instructions is given by an arrow. Example:
1. Instruction 1
Reaction of the implement to handling instruction 1
2. Instruction 2
Listings without a mandatory sequence are presented as a listing with bullets.
Example: Point 1
Point 2
Numbers in round brackets refer to the item numbers in the illustrations. The first number refers to the
diagram and the second number to the item.
Example: (Fig. 3/6) = Figure 3 / Position 6
All the directions specified in the operating manual are always viewed in the direction of travel.
General Safety Instructions
14 Cirrus 03 BAH0101-05 11.19
2 General Safety Instructions
This section contains important information on safe operation of the
implement.
2.1 Obligations and liability
Comply with the instructions in the operating manual
Knowledge of the basic safety information and safety regulations is a
basic requirement for safe handling and fault-free implement
operation.
Obligations of the operator
The operator is obliged only to let those people work with/on the
implement who
are aware of the basic workplace safety information and accident
prevention regulations
have been trained in working with/on the implement
have read and understood this operating manual.
The operator is obliged
to keep all the warning symbols on the implement in a legible
state
to replace damaged warning symbols.
Obligations of the user
Before starting work, anyone charged with working with/on the
machine is obliged
to comply with the basic workplace safety instructions and
accident prevention regulations
to read and understand the "General safety information" section
of this operating manual
to read the section "Warning symbols and other labels on the
implement" in this operating manual and to follow the safety
instructions represented by the warning symbols when operating
the implement
to get to know the implement
to read the sections of this operating manual, important for
carrying out your work.
If the user discovers that a function is not working properly, then they
must eliminate this fault immediately. If this is not the task of the user
or if the user does not have the appropriate technical knowledge, then
they should report this fault to their superior (operator).
General Safety Instructions
Cirrus 03 BAH0101-05 11.19 15
Risks in handling the implement
The implement has been constructed to the state-of-the art and the
recognised rules of safety. However, operating the implement may
cause risks and restrictions
the health and safety of the user or third persons
the implement itself
other property.
Only use the implement
for the purpose for which it was intended
in a perfect state of repair.
Eliminate any faults immediately which could impair safety.
Guarantee and liability
Our "General conditions of sales and delivery" are always applicable.
These shall be available to the operator, at the latest on conclusion of
the contract. Guarantee and liability claims for damage to people or
property will be excluded if they can be traced back to one or more of
the following causes:
Improper use of the implement
Improper installation, commissioning, operation and mainte-
nance of the implement
Operation of the implement with defective safety equipment or
improperly attached or non-functioning safety and protective
equipment
Non-compliance with the instructions in the operating manual re-
garding commissioning, operation and maintenance
Unauthorised design changes to the implement
Insufficient monitoring of implement parts which are subject to
wear
Improperly executed repairs
Disasters due to the effects of foreign objects and force majeure.
General Safety Instructions
16 Cirrus 03 BAH0101-05 11.19
2.2 Representation of safety symbols
Safety instructions are indicated by the triangular safety symbol and
the highlighted signal word. The signal word (DANGER, WARNING,
CAUTION) describes the severity of the risk, and carries the following
meaning:
DANGER
Indicates an immediate hazard with high risk, which will result
in death or serious bodily harm (loss of limbs or long-term
harm), if it is not avoided.
If the instructions are not followed, then this will result in
immediate death or serious physical injury.
WARNING
Indicates a medium risk, which could result in death or (serious)
physical injury if not avoided.
If the instructions are not followed, then this may result in death
or serious physical injury.
CAUTION
Indicates a low risk which could cause minor or medium level
physical injury or damage to property if not avoided.
IMPORTANT
Indicates an obligation to special behaviour or an activity required for
proper implement handling.
Non-compliance with these instructions can cause faults on the
implement or disturbance to the environment.
NOTE
Indicates handling tips and particularly useful information.
These instructions will help you to use all the functions of your
implement in the best way possible.
General Safety Instructions
Cirrus 03 BAH0101-05 11.19 17
2.3 Organisational measures
The operator must provide the necessary personal protective
equipment as per the information provided by the manufacturer of the
crop protection agent to be used, such as:
Safety glasses
Protective shoes
Chemical-resistant overalls
Skin protection agents, etc.
The operating manual
must always be kept at the place at which the implement is
operated
must always be easily accessible for the user and maintenance
personnel.
Check all the available safety equipment regularly.
2.4 Safety and protective equipment
Before starting up the implement each time, all the safety and
protection equipment must be properly attached and fully functional.
Check all safety and protection equipment regularly.
Faulty safety equipment
Faulty or disassembled safety and protection equipment can lead to
dangerous situations.
2.5 Informal safety measures
As well as all the safety information in this operating manual, comply
with the general, national regulations pertaining to accident prevention
and environmental protection.
When driving on public roads and routes you should comply with the
statutory road traffic regulations.
General Safety Instructions
18 Cirrus 03 BAH0101-05 11.19
2.6 User training
Only those people who have been trained and instructed may work with/on the implement. The
operator must clearly specify the responsibilities of the people charged with operation and
maintenance work.
People being trained may only work with/on the implement under the supervision of an experienced
person.
Person
Activity
Person specially
trained for the
activity 1)
Trained person 2)
Person with
specialist training
(specialist
workshop) 3)
Loading/Transport X X X
Initial operation X
Set-up, tool installation X
operation X
Maintenance X
Troubleshooting and fault
elimination
X X
Disposal X
Key: X..permitted ..not permitted
1) A person who can assume a specific task and who can carry out this task for an appropriately
qualified company.
2) Instructed persons are those who have been instructed in their assigned tasks and in the
possible risks in the case of improper behaviour, have been trained if necessary, and have been
informed about the necessary protective equipment and measures.
3) Persons with specialised technical training shall be considered as a specialist. Due to their
specialist training and their knowledge of the appropriate regulations, they can evaluate the work
with which they have been charged and detect possible dangers.
Comment:
A qualification equivalent to specialist training can be obtained from several years' experience in
the relevant field.
Only a specialist workshop may carry out maintenance and repair
work on the implement, if such work is additionally marked
"Specialist workshop". The personnel of a specialist workshop shall
possess the appropriate knowledge and suitable aids (tools, lifting
and support equipment) for carrying out the maintenance and repair
work on the implement in a way which is both appropriate and safe.
General Safety Instructions
Cirrus 03 BAH0101-05 11.19 19
2.7 Safety measures in normal operation
Only operate the implement if all the safety and protection equipment
is fully functional.
Check the implement at least once a day for visible damage and
check the function of the safety and protection equipment.
2.8 Danger from residual energy
Note that there may be residual mechanical, hydraulic, pneumatic and
electrical/electronic energy on the implement.
Use appropriate measures to inform the operator. You can find
detailed information in the relevant sections of this operating manual.
2.9 Maintenance and repair work, fault elimination
Carry out prescribed setting, maintenance and inspection work in
good time.
Secure all media such as compressed air and the hydraulic system
against unintentional start-up.
Carefully fix and secure larger assembly groups to lifting units when
carrying out replacement work.
Check all the bolted connections for tightness. On completion of the
maintenance work, check the function of the safety and protective
devices.
General Safety Instructions
20 Cirrus 03 BAH0101-05 11.19
2.10 Design changes
You may make no changes, expansions or modifications to the im-
plement without the authorisation of AMAZONEN-WERKE. This also
applies when welding support parts.
A
ny extension or conversion work shall require the written approval of
AMAZONEN-WERKE. Only use modification and accessory parts ap-
proved by AMAZONEN-WERKE so that the type approval, for exam-
ple, remains valid in accordance with national and international regu-
lations.
Vehicles with an official type approval or with equipment connected to
a vehicle with a valid type approval or approval for road transport ac-
cording to the German road traffic regulations must be in the state
specified by the approval.
WARNING
Risk of crushing, cutting, being trapped or drawn in, or impact
through the failure of support parts.
It is strictly forbidden to
drill holes in the frame or on the running gear
increase the size of existing holes on the frame or the running gear
weld on load-bearing parts.
Other manuals for Cirrus 03
2
Table of contents
Other Amazone Farm Equipment manuals
Amazone
Amazone Cayena 6001 User manual
Amazone
Amazone ZA-M 3001 User manual
Amazone
Amazone Citan 12001-C User manual
Amazone
Amazone Cirrus 3000 User manual
Amazone
Amazone ZA-M Profis Hydro User manual
Amazone
Amazone Ceus 3000-TX Installation instructions
Amazone
Amazone ZG-TS 7501 Truck User manual
Amazone
Amazone UX 6201 Super User manual
Amazone
Amazone Precea 3000 Installation instructions
Amazone
Amazone Catros 2503 Special User manual
Amazone
Amazone Tyrok 400 OL Quick guide
Amazone
Amazone KX Series User manual
Amazone
Amazone Tyrok 400 Installation instructions
Amazone
Amazone Limiter M User manual
Amazone
Amazone AMASPRAY+ User manual
Amazone
Amazone D9 2500 Special User manual
Amazone
Amazone DMC Primera 9001-2C User manual
Amazone
Amazone Cataya User manual
Amazone
Amazone EDX 6000-2 User manual
Amazone
Amazone CombiDisc 3000 Installation instructions
Popular Farm Equipment manuals by other brands
Ferrari Costruzioni Meccaniche
Ferrari Costruzioni Meccaniche FPA Operating and service manual
Pottinger
Pottinger NOVACAT V 10000 Original operating instructions
Bigham
Bigham Lilliston Rolling Cultivator Generation 3 Operator's manual
JF
JF R 420 DS Operator's manual
SKY Agriculture
SKY Agriculture Methys FT Original instructions
Original inside
Original inside TOP 620 A Operator's manual
