Assa Abloy DC6210 Series User manual

80-9360-6007-152 04/18
Installation Instructions
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Important
• An improperly installed or incorrectly adjusted door closer may cause property damage or personal injury; and will void
product warranty.
• To avoid personal injury, DO NOT DISASSEMBLE THIS DOOR CLOSER BODY.
• Door closers must be securely fastened to a properly reinforced door and frame with fasteners provided.
• An auxiliary door stop, BY OTHERS, is required for this Installation.
• Arm is handed and must match hand of door.
DC6210 Series
DC6410 Series
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
A14 Heavy Duty Friction Hold Open Parallel Arm

2
80-9360-6007-152 04/18
DC6210 and DC6410 Series Closers
Installation Instructions
A14 Heavy Duty Friction Hold Open Parallel Arm
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
*DC6410 Series recommended.
**NOTE: These forces are for standard templating with bearing type hinges and do not account
for pressure differentials and draft. Half size closers DC6410 are capable of being adjusted to
next higher setting.
Size of Door & Door Closer
Type of
Installation Interior Exterior In-swinging
Exterior
Out-swinging
Recommended
Closer Size
**Max. Opening
Force lbs/f
Parallel Arm
2' 4" - - 1 8
2' 6" - - 2 14
3' 0" - 2' 6" 3 16
3' 6" - 3' 0" 4 22
4' 0" - *3' 6" 5 24
4' 6" - *4' 0" 6 26
TO DETERMINE
HAND OF
YOUR DOOR:
LEFT
HAND
DOOR
RIGHT
HAND
DOOR
RHR LHR
1 Introduction
L
3/8
(10)
1/4-20 THREAD
Drill thru 9/32 (7.1) Enlarge to
3/8
(9.5) Dia. This Side Only
(4 Places)
DOOR
THICKNESS
SEX NUT
LENGTH “L”
1-3/8" (35mm)
1--3/4" (44mm)
&OVER
1-9/32" (33mm)
1-21/32" (42mm)
MOUNTINGSCREW SPECIFICATIONS
ARM AND CLOSER BRACKET
}
or{Option M54:
Sex nuts, furnished
when ordered
1/4-20 oval head machine
screw or 1/4-14 self-drilling
screw Type BSD. 3/16 (4.8)
diameter pilot hole required
forWood Applications.
L
3/8
(10)
1/4-20 THREAD
Drill thru 9/32 (7.1) Enlarge to
3/8 (9.5) Dia. This Side Only
(4 Places)
DOOR
THICKNESS
SEX NUT
LENGTH “L”
1-3/8" (35mm)
1--3/4" (44mm)
&OVER
1-9/32" (33mm)
1-21/32" (42mm)
MOUNTINGSCREW SPECIFICATIONS
ARM AND CLOSER BRACKET
}
or{Option M54:
Sex nuts,
furnished
when ordered
1/4-20 oval head machine
screw or 1/4-14 self-drilling
screw Type BSD. 3/16 (4.8)
diameter pilot hole required
forWood Applications.
Figure 1
BEFORE INSTALLING:
• The Americans with Disabilities Act (ADA) requires that doors having door closers have an opening force not to
exceed 5 lbf.
• The door closer’s power size adjustment feature may require adjustment to its lowest setting to comply with ADA
opening force guidelines.
• ADA compliant closers: DC6210 and DC6411.
Heavy Duty Friction Hold Open
Friction Hold
Open
Adjustment
Nut
No Drill Mark
Right Hand Arm
Drill Mark
Left Hand Arm

3
80-9360-6007-152 04/18
DC6210 and DC6410 Series Closers
A14 Heavy Duty Friction Hold Open Parallel Arm
Installation Instructions
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
2 Installation
1. Template
Mark and prepare door and jamb (for closer
bracket and arm bracket). Use template and
dimensions charted. (Figure 2)
NOTES:
• Check hand of door. (Figure 1)
• Right Hand Application Shown,
Left Hand Opposite
• Dimensions given in inches (mm). Do Not Scale Drawing.
• Closer must be installed in a true horizontal plane to
ensure proper closer performance.
• Friction Hold Open arms are handed and not reversible.
See handing marks on soffit plate.
Figure 2
Opening
Maximum DIM. A DIM. B DIM. C Application
90° 12-3/4"
(324mm)
11-5/8"
(295mm)
27-3/4"
(705mm) NON A.D.A.
180° 8-11/16"
(221mm)
7-9/16"
(192mm)
23-5/8"
(600mm)
2
(50.8)
2
(50.8)
2
(50.8)
1
(25.4)
1-1/2
(38.1)
SEE MOUNTING SCREW
SPECIFICATIONS
NOTE: ANGLE SUPPORT MUST BE
DRILLED AND TAPPED IN THE FIELD
447F14 DOOR
FRAME
M85OPTION 447F14
ANGLE SUPPORT BRACKET
5/8
(16)
REF.
DOOR
FRAME
ARM
BRACKET
SP
ACER BLOCK
(When
required)
5/8
(16)
2-3/8
(60)
FRAME STOP
TOPOF DOOR
C
L
HINGE
OR
PIVOT
DOOR
FRAME STOP
2-3/4
(70) 5/8
(16)
1-1/2
(38.1)
1/4
(6.35)
CLOSER
BRACKET
1
(25.4) 4-5/16
(109.5)
B
A
TYP.
15/16
(23.8)
3/4
(19) 1-3/8
(35)
C
Minimum Clearance

4
80-9360-6007-152 04/18
DC6210 and DC6410 Series Closers
Installation Instructions
A14 Heavy Duty Friction Hold Open Parallel Arm
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Pin Hole End
Countersunk Holes
Holding Pins
1/4-20 x 1/2 OHMS (2)
2 Installation
2. Install Closer Bracket. (Figure 3)
Figure 3
3. Mount Closer Body to Closer Bracket.
(Figure 4)
Figure 4
Pin Hole End
Countersunk Holes
Holding Pins
1/4-20 x 1/2 OHMS (2)
1/4-14 x 1-1/2
OH Self-Drilling (4)
or
1/4-20 x 3/4 OHMS w/Sex
Nuts (4) (M54 Option)

5
80-9360-6007-152 04/18
DC6210 and DC6410 Series Closers
A14 Heavy Duty Friction Hold Open Parallel Arm
Installation Instructions
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Figure 5
4. Fasten Soffit Plate to Frame Soffit (under
side of frame).
5. Connect Arm To Closer. (Figure 5)
Using hex wrench provided, close (turn
clockwise) CLOSING SPEED VALVE (see
page 5 for location on closer). DO NOT
OVER TIGHTEN.
• Open door to approximately 60°.
• Using wrench on underside of spindle,
rotate spindle approximately 135° toward
hinge edge of door.
• Install arm on spindle at an approximate 90°
angle to door.
• Reopen CLOSING SPEED VALVE.
• Install and tighten arm washer and screw.
DOOR
SPINDLE
ARM
CENTERLINE
ALL ANGLES SHOWN ARE APPROXIMATE
DOOR
90°
SPINDLE
ROTATED 135°
Rotate 135°
SPINDLE AT REST
60°
DOOR
135°
WRENCH
90°
ARM
2 Installation
6. Adjust Hold Open Position. (Figure 6)
Open door to desired degree of hold open. (If
door does not open far enough, loosen Hold
Open Adjustment Nut.) Place door at desired
degree for hold open and tighten Hold Open
Adjustment Nut.
Rotation:
Counter-clockwise will increase (+) angle.
Clockwise will decrease (-) angle.
NOTE: Pushing door beyond set hold
open point may cause damage to product.
Friction Hold Open
Adjustment Nut
+
Figure 6

6
80-9360-6007-152 04/18
DC6210 and DC6410 Series Closers
Installation Instructions
A14 Heavy Duty Friction Hold Open Parallel Arm
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
3 Adjustments
Adjustments (Figure 7)
(3/32 Allen Wrench Provided)
Closing Speed Valve (Figure 8)
To adjust speed of door closing from fully
open to a position 2 to 5" from closed, turn
Closing Speed Valve CLOCKWISE to SLOW
closing, COUNTER-CLOCKWISE to SPEED
closing.
Latching Speed Valve (Figure 9)
After closing speed has been obtained, turn
latching speed valve CLOCKWISE to SLOW
latching or COUNTER-CLOCKWISE to SPEED
latching for last 2" to 5" of door travel.
NOTE: Set combination of CLOSING and
LATCHING speeds to between 3 and 7
seconds. Use of door by handicapped,
elderly or small children, may require
even greater closing time.
Backcheck Location Valve (Figure 8)
Valve is closed, as shipped, from factory.
To increase degree of door opening where
backcheck takes effect, turn valve counter-
clockwise. When valve is closed, backcheck
occurs at approximately 65°-70°. When valve
is open, backcheck occurs at approximately
95°-100°.
Backcheck Intensity Valve (Figure 8)
Turn valve COUNTER- CLOCKWISE to reduce
backcheck or CLOCKWISE to increase
backcheck. (Backcheck should be set to give
a soft cushioning action, not a sudden stop).
Delayed Action Valve (Figure 8)
Turn valve CLOCKWISE to SLOW closing,
COUNTER-CLOCKWISE to SPEED closing.
Delayed action may be adjusted from 20
seconds to 90 seconds, depending on degree
of door swing. Delay occurs at the beginning
of the door closing cycle from fully open down
to 70°, where the closing speed valve then
begins its control.
Delayed Action
Option
M-71
Backcheck
Latch
Sweep
LATCHING
SPEED
VA LV E
Power
Size
Stamp
Date Stamp
BACKCHECK
INTENSITY VALVE
BACKCHECK
LOCATION VALVE
CLOSING
SPEED VALVE
SPRING
POWER ADJUSTER
(5/16" WRENCH or SOCKET)
(FLATTIP SCREWDRIVER
)
OPTION M71
DELAYED
ACTION VALVE
Figure 7
Figure 8
Figure 9

7
80-9360-6007-152 04/18
DC6210 and DC6410 Series Closers
A14 Heavy Duty Friction Hold Open Parallel Arm
Installation Instructions
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
3 Adjustments
Adjust Spring Power According to Chart
DC6200 Size 1-6 Adjustment (Figure 10)
DC6400 Half Size Adjustment as Desired
• All DC6200 closers are factory set at an
approximate Size 3.
Full Cover(Standard)
Slim Cover (Option M76)
Figure 10
Figure 11
Figure 12
4 Cover Installation
Full Cover(Standard)
Slim Cover (Option M76)
Install Cover (Figure 11)
Slip cover over closer. Hold tightly against
closer mounting surface. Secure on each
side with 6-32 x 1/4 PBHMS screws.
Slim Cover Option M76 only (Figure 12)
Position spindle cap over unused spindle
and secure with truss head screw.
• Adjust closer as necessary for door size
using this chart.
• Readjustment may be required to suit
prevailing conditions.
Size of Door No. of Full (360°)
Turns Clockwise of
Power Adjuster
Equivalent Closer
Size (Approx.)
Interior Exterior
In-Swinging
Exterior
Out-Swinging
2' 4"
(712)
2' 6"
(764) - 4 2
2' 6"
(764)
3' 0"
(915) - 8 3
3' 0"
(915)
3' 6"
(1067)
2' 6"
(764) 12 4
3' 6"
(1067)
4' 0"
(1219)
3' 0"
(915) 16 5

80-9360-6007-152 04/18
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Patent pending and/or patent: www.assaabloydss.com/patents
Corbin Russwin
225 Episcopal Road
Berlin, CT 06037
Phone: [phone]
Fax: [phone]
corbinrusswin.com
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]