Axkid Babyfix User manual

Babyx
Instruction manual
Tested and approved according to
ECE R44 / 04
Baby seat
Approved according to Group 0+ for
babies weighing up to 13kg

ank you for choosing a baby seat from Axon Kids. e team developing Babyx
have more than 30 years of experience in child safety products between us, and we
have done our outmost to make this baby seat as safe as possible. e Axon Kids
baby seat has of course also been tested and certied according to ECE R44/ 04,
the latest European standard for child safety.
To maximize your child’s safety, please observe the following:
Read the instruction manual carefully before you
assembly the baby seat. Otherwise you risk to
seriously harm your child.
Read the instructions thoroughly before you attempt to install
the seat. If you have any doubts, please contact your store of
purchase, which can show you the correct installation. Incorrect
installation means danger to your child.
Never mount the child seat in a seat with an active airbag. If you
still wish to use the seat, disconnect the airbag at an authorized
service center, or if your car is equipped with it, use the key to
turn the airbag o. It is important to always note if the car’s in-
dicator shows that the airbag is turned o.
In case of a car accident, no matter how small, always replace the
car seat. It may have invisible damage that seriously aects your
child’s safety. is is also the reason for why you never should
buy a used child seat. Axon Kids recommendation is that you
always should buy a new chair in a store.
Never use this babyseat in a car seat that is not equipped with
an approved tree-point belt. Please refer to vehicle list.
Important information

The baby seat’s parts
1. Handle
2. Release buttons for the handle
3. Belt guiding hook
4. Cradle skids
5. Belt release button
6. Belt adjust release button
7. Belt adjustment strap
8. Sun protective cloth
9. Handle status indicator
10. Push-chairxing
8.
9.
10.

In order to adjust the handle; push
both the release buttons located close to
the handle’s rotation point. At the same
time, push the handle in the direction
of the arrow (Pic 1). e handle has
ve dierent positions to choose from.
Picture 1. is position shall be
used when carrying the child or when
mounting the baby seat in the vehicle.
Picture2. is position shall be
used when the baby seat is used as a
cradle or when assemblied in car.
Picture 3. is position should
be used when the baby seat is as-
semblied in the car and you would
like extra access to your child.
Picture 4. is position shall be used
when using the baby seat as a cradle or
when mounted in a compatible stroller.
Picture 5. is position blocks the
cradle function and can be used when
you don’t want the cradle function for
example when feeding your child etc.
Adjusting the handle
4

Buckle your child in the seat
5
Put the baby seat on a plane surface
and then adjust the handle so that it is
according to picture 1 on the previous
page. Hold down the button for belt
adjustment (Pic 6, B) and at the same
time pull the shoulder belt (Pic 6, A)
until it is fully pulled out.
en fold away the shoulder belts so
that they will be easy to get hold of
after you have placed your child in the
baby seat. If your child is older then 2
months of age the insert cushion shall
be removed (Pic 6, D).
Now place your child in the baby seat.
Make sure that the shoulder belts run
over your child’s shoulders. When this
is done put the two shoulder belt’s
locks together and put them in to the
belt buckle (Pic 7).
e belt locks only t together in one
way. Make sure that the belt is secured
(Pic 8). Belts should then be tightened
by pulling belt strap (Pic 6, C).
Important!
When adjusting the shoulder belts on
the child seat it is important that you
have the child seat on a plane surface.
e reason for this is that the child’s
position could be very dierent if the
seat is angled which may cause that the
belt is not tightened enough.
Please make sure that belts are properly adjusted
to your child and that the belt are not twisted in
any way.

6
e height of where the shoulder belt
comes out from the baby seat’s back
should be just below the child’s shoul-
ders.
Adjusting is done by moving the belt up
or down to the next slit, picture 9, in the
baby seat’s back depending on if you are
going to increase the height or decreas-
ing it.
Create some slack on the shoulder belt
by using the belt adjusting button and
pulling the shoulder belts at the same
time. en un-hook the belts from the
triangular metal plates on the baby seat’s
back side (Pic 10). Now you can pull
out the belts from the current slit. en
put the belts in a dierent slit that better
suits your child’s height. en hook the
belt back to the triangular steel plates.
Important!
Make sure that the belts are secured in
the triangular steel plates.
Adjusting the belt height

7
1. Start by adjusting the handle
of the seat so that it is xed to a vertical
position.
2. Guide the car’s lap belt through
the hooks on the baby seat’s front side.
en buckle the belt (Pic 11)
3. Pull the car’s shoulder belt
around the seat and x it in the hooks
on the rear side of the seat (facing for-
ward in the car) (Pic 12 and Pic 13).
4. Push down the baby seat in the
vehicle’s seat and then pull the belt as
hard as you can to make sure that the
baby seat gets the most xed position
possible.
Important!
e baby seat can only be used in posi-
tions where there is no active airbag and
where there is 3-point belt system.
Installation in the car
Do not use any other belt routing then
described in this manual. If so you are facing a
risk that your child is not properly fastened.

If the baby seat cover is replaced; make sure only to use original products
from Axon Kids. If not the safety system could be compromised and may
lead to death or injury of your child in case of an accident.
e baby seat cover can be taken o and washed in the laundry. Use the
“handwash”-program or similar (max temp 30 ˚ C ). Do not use the dryer
since this can cause the padding to detach from the cloth. Never use the
baby seat without it´s cover.
e plastic details of the baby seat shall be cleaned with a non aggressive
cleaning chemicals such as soap water. Aggressive chemicals like solvents etc
may cause damage to the material and by this compromise the safety of the
child seat.
e parts of the baby seat can be recycled and shall be sorted in compliance
with your local legislation. Ask your local recycling center for advice when
recycling the product.
Do not do any repairs or any adjustment to the baby seat other then those
described in this user guide.
Our warranty policy is inline with your local consumer
agency. Make sure to save your receipt and bring it to your dealer if you have
any warranty issues. e warranty does not cover:
o Wear down as a consequence of normal use.
o Damages as a consequence of incorrect use.
All our materials keep a very high standard with respect to UV-resistance (sun
light). In long term UV light is very aggressive and will lead to that the cloth
will be bleached. is is not covered by the warranty since it is considered as
normal usage.
Never leave your child unattended in the baby seat.
Any luggage or other objects liable to cause injuries in the event of a collision
shall be properly secured.
Store this user manual in a safe place.
Warranty and handling
8
Producer:
Axonkids AB
Box 188
53322 Götene
www.axonkids.com