Ballard Designs Gracie WN202 User manual

PRODUCT NAME: Gracie Mirror
ITEM NUMBER: WN202
ASSEMBLED DIMENSIONS : 60.7”H x 25.75”W x 1.42”D
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN CHINA
UPDATED: 10/04/2019 Page 1 of 5

TOOLS NEEDED:
Phillips Screwdriver, Pencil, Hammer,
Drill with 3/8” bit
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
NOTE: To avoid accidentally
discarding small parts or hardware,
retain all carton contents until
assembly and installation are complete.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 5
Ltr. Qty.
Hardware Included
A
2
W
ood Screws
B
2 Expansion Bolt
C 2
W
all Anchoring
Anti-T
ip Kit
(PAGE 5)
Ltr. Qty.
Components
D
1
Mirror

WARNING
Falling Hazard
MIRROR IS VERY HEAVY AND REQUIRES ADEQUATE SUPPORT
AT LEAST ONE BRACKET MUST SECURED TO A WALL STUD
(D)
NOTE: This Mirror is designed for either hanging on or leaning against a wall.
WALL HANGING INSTALLATION
STEP 1: When determining location for Mirror (D) AT LEAST ONE KEYHOLE BRACKET MUST BE
POSTIONED OVER A WALL STUD. Use pencil to mark location of Keyhole Brackets on back of Mirror.
NOTE: For location not over a wall stud, use Expansion Bolt (B) installation covered in Steps 2 and 3.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Page 3 of 5
WALL STUD
Wood Screw (A)
Expansion Bolt (B)
(Open Drywall)
keyholes

EXPANSION BOLT (For use in open drywall where no wall stud is present)
STEP 2: If mark falls in area in with no wall stud, use Drill with 3/8” bit to create a hole through
drywall. Use hammer to lightly tap Expansion Bolt (B) into hole until teeth sink into wall surface.
STEP 2: Using a screwdriver, firmly press down and turn Bolt clockwise until it starts to slip which
indicates barrel has crimped against inside of wall. Back Bolt out just enough to permit Keyhole
bracket to slip over and mirror to be hung.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Page 4 of 5

( F)
(G)
(D)
NOTE: WHEN LEANING MIRROR AGAINST WALL IT MUST BE ACHORED
TO A WALL STUD AND IN NO WAY SUSPENDED.
ANTI-TIP / WALL ANCHORING HARDWARE INSTALLATION:
Ltr. Qty. Hardware Included
A
2
Screw
B
2
Bracket
C
2
Retention Belt
1.
Locate and mark a Wall Stud behind mirror at location for installation.
2.
Wall Stud must line up with at least one Keyhole Bracket on back of mirror.
3.
Using screwdriver, attach Bracket (B) by driving Screw (A) through hole an into WALL STUD.
4.
Move mirror into place, align Brackets then connect both using Retention Belt (C).
5.
Confirm Belt is securely laced and locked.
WARNING
Tip-Over Hazard
WALL BRACKET MUST BE ATTACHED TO WALL STUD
Prevent tipping accidents. Anchor your mirror.
(B)
(A)
(C)
Wall
Cleaning & Care:
DO NOT use alcohol based products or spray polisher as finish damage may result.
Dust with a soft cloth.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Page 5 of 5