Ballard Designs JC301 User manual

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 12/31/19 Page 1 of 6
PRODUCT NAME: Sunday Daybed Swing
ITEM NUMBER: JC301
ASSEMBLED DIMENSIONS: 22”H x 82”W x 43.3”D
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN VIETNAM

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 6
Ltr.
A 4
B
Hooks
Large Screws14
Qty. Hardware Included
Ltr.
M 1
L 1
K 1
J 1
I 1
Qty. Components
C 4 Small Screws
REQUIRED TOOLS:
Allen Wrench (included),
Rubber Mallet
-Assembly requires 2 people
and a
LICENSED CONTRACTOR*
(See Step 6)
NOTE: When unpacking, lay
the parts on a padded surface
such as the packaging provided.
Be sure to locate all hardware
before throwing away any
packaging.
D 2
E
Brackets
Medium Screws6
F 10
G 4
H 1
Plugs
Chains
Allen Wrench
Right Arm (I)
Left Arm (J)
Back (K)
Seat (L)
Seat Cushion (M)
Assemble in location for intended use.

Page 3 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(A)
(H)
(I)
(J)
(B)
(B)
(K)
(L)
Place Hooks (A) into holes on top of Right Arm (I) and Left Arm (J). Thread and firmly
STEP 1: INSTALL HOOKS. Place Hooks (A) into holes in top of Right Arm (I) and Left Arm (J).
Thread into metal embedded in base of hole and firmly tighten.
NOTE: Holes face outward. Notch inward.
B
AL
L
ARD
DES
I
GNS
sSTEP 2: ATTACH BACK TO SEAT. Place Back (K) onto Seat (L) as illustrated. Insert Large Screws (B)
and firmly tighten using Allen Wrench (H).
Brass branding label faces outward.

(E)
(E)
(E)
(H)
(H)
(D)
(I)
(J) (K)
(L)
(B)
(B)
(H)
(I)
(J)
(K)
(L)
Page 4 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 3: ATTACH ARMS. Carefully fit Right Arm (I) and Left Arm (J) onto Seat (L) and Back (K). Align
dowels and fit them into notches. NOTE: A Rubber Mallet may be needed to completely seat dowels.
Insert Large Screws (B) into each hole and tighten using Allen Wrench (H).
(C)
STEP 4A: STEP 4B:
STEP 4A: Invert Swing then insert Medium Screws (E) into holes as illustrated. Firmly tighten using
Allen Wrench (H).
STEP 4B: Align Brackets (D) over pre-drilled holes as illustrated. Insert Small Screws (C) into holes
and firmly tighten using Allen Wrench (H).
B
A
LL
ARD
D
E
S
I
G
N
S

Page 5 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(G)
(A)
(F)
(F)
(I)
(J)
Attach Chains (G) to Hooks (A).
STEP 5: COVER VISIBLE HOLES. Return Swing upright and insert a Plug (F) into each hole on side
of Right Arm (I) and Left Arm (J). NOTE: A Rubber Mallet may be needed to gently tap and seat Plug.
STEP 6: Swing can support up to 800 lbs. *To prevent personal or property damage, all swings
should be installed by a Licensed Building Contractor. Hanging hardware is not included as it
needs to be determined on site. Building support beams must be adequately designed and/or
reinforced to support at least the rating of the swing. Connect Chains (G) to Chain Hooks (A).
WARNING
Falling Hazard
SWING MUST BE SUPPORTED BY ADEQUATE STRUCTURE
Consult with a Licensed Building Contractor before installation.

(M)
Page 6 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 7: Place Seat Cushion (M) on Swing.
Cleaning and Care
Please refer to care instructions on product hang tag.