Ballard Designs SINCLAIRE TOWER MQ104 User manual

Customer Service: 800-367-2810
Online: www.ballarddesigns.com
PRODUCT NAME: SINCLAIRE TOWER
ITEM NUMBER:MQ104
DIMENSIONS OF ITEMASSEMBLED: 81 1/2”H x 20 7/8”W X 16”D
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE. MADE IN CHINA
UPDATE: 09/28/2018 Page 1 of 7

Page 2 of 7
Online: www.ballarddesigns.com
NOTE: Assemble the Tower in desired location for use.
Hardware Located
Here (A-G)
Shelves
(H,I)
TOOLS NEEDED:
-Requires a screwdriver.
-Power drill suggested.
-Assembly requires 2 or more people.
NOTE: When unpacking, lay the parts on
a padded surface such as the packaging provided.
Be sure to locate all hardware before throwing
away any packaging.
Customer Service: 800-367-2810
Ltr. Qty.
Components
H 3
Glass Shelves (H)
I 1
Shelf (I)
Ltr. Qty. Hardware Included Ltr. Qty. Hardware Included
A
16
Shelf Supports
E 2
Connector Plates
B
8
Long Screws
F 4
Connector Screws
C 8
Small Screws
G 4
Wood Plugs
D 2
L-Brackets

Page 3 of 7
Online: www.ballarddesigns.com
NOTE: Assemble the Tower in desired location for use.
STEP 1: Place the Shelf Supports (A) at the desired Shelf heights and lay the Shelves (H) (I)
on the Supports.
STEP 2: If the Tower is uneven, adjust the levelers inside the bottom corners of the Bookcase by
using a flat head screwdriver. Turn clockwise or counterclockwise until the unit sits evenly.
Cover the leveler holes with the wood plugs (G).
Customer Service: 800-367-2810
(G)
A
I
A

Page 4 of 7
Online: www.ballarddesigns.com
NOTE: Assemble the Tower in desired location for use.
STEPT 3: The door can be reversible by turning the door upside down and relocating the 2 hinges
from the left to the right and the door magnet from the top right to the top left as illustrated.
STEP 4: Attached the two by aligning the Connector Plates (E) with pre-drilled holes on
the backs and screw in the Connector Screws (F).
Customer Service: 800-367-2810
E
F
MQ104 MQ104
MQ103
MQ102

Page 5 of 7
Online: www.ballarddesigns.com
NOTE: Assemble the Tower in desired location for use.
STEP 5: Center the Tower in front of two Studs and mark the Wall. Push the Bookcase against the
Wall.
STEP 6: Slide the L-Bracket (D) over the top corner of the Bookcase Top in front of the previously
marked Stud and mark the Wall at the top of the L-Bracket.
NOTE: It is important that the L-Bracket is positioned like the picture below in order to
hide the Bracket.
Customer Service: 800-367-2810
D
IMPORTANT:
Installing the L-Bracket (D) to a Wall Stud
and the Bookcase is REQUIRED before any
use of the product for customer safety.

Page 6 of 7
Online: www.ballarddesigns.com
NOTE: Assemble the Tower in desired location for use.
STEP 7: Pull the Bookcase away from the Wall and attach the L-Brackets (D) to the Studs using
the Long Screws (B).
STEP 8: Slide the Bookcase underneath the previously installed L-Brackets (D) and use 2 or more of
the Small Screws (C) to attach the L-Brackets to theBookcase.
NOTE: The L-Brackets may not be completely on the Bookcase’s Top due to the Wall’s base
molding. Only screw into the Bracket holes that are completely on the Bookcase Top.
Customer Service: 800-367-2810
C
D
D
B

NOTE: Save this page for future bulb replacement.
HALOGEN BULB REPLACEMENT:
Unplug the unit from the wall. Remove the Lens Cover (B) from the Fixture Body (C) by turning it
counter clockwise and pulling it away from the unit. Remove the old Bulb (A) by pulling it straight
out in a horizontal direction.
Insert the new Bulb (A) into the Fixture Body (C) Socket using a tissue or soft cloth (oil from the
skin may damage the bulb). Replace the Lens Cover (B) by twisting it clockwise back into place.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 7 of 7
(C)
(A)
(B)
(C)
(B)
Qty.
Item needed
1
Halogen JCD G8 120V 25W
Replacement Bulb (A) NOT
INCLUDED