Ballard Designs SR064 User manual

Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 7-21-2020 Page 1 of 7
PRODUCT NAME: Thayer Wine Cubes
ITEM NUMBER: SR064
ASSEMBLED DIMENSIONS : 78.25”H x 25.75”W x 16.3”D
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN INDONESIA

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 7
Ltr.
A12
B12
Qty. Hardware Included
Ltr.
G
I
1
2
Qty. Components
C 8
REQUIRED TOOLS:
Phillips Screwdriver,
Drill with 3/8” Bit, Pencil
Allen Wrench (included)
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
Small Screws
Large Screws
Allen Bolts
Flat Washers
D 8
Allen Wrench
E1
H1
Frame (G)
X Box(H)
Grid Boxes (I)
Cleaning and Care
Periodically dust with a soft, dry cloth.
Prevent finish damage: do not use alchohol based
cleaners or polishers. Promply remove spills.
F2
Wall Anchoring
(Anti-tip) Hardware Kits
See Page #
WARNING
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
ANCHORING HARDWARE INCLUDED
Assemble in location for intended use.

Page 3 of 7
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 1: Front and back of Frame (G) connected by folding hinges. Carefully pull Frame apart and
straighten hinges as illustrated. Position attached Support Brackets, align holes then insert Allen Bolt
(C) with Flat Washer (D). Insert ALL Bolts and Washers on all Support Brackets then fully tighten and
secure using Allen Wrench (E).
Pinch Point Hazard
Folding Hinge Brackets
CAUTION
(C)
(D)
(E)
Support Brackets
Folding Hinge Brackets
STEP 2: Carefully insert an Grid Box (I) into upper compartment in Frame (G). Orient Box with label(s)
facing down toward Legs on Frame. Insert LARGE SCREWS (B) through hole in pre-installed Tabs
mounted onto Frame. Fully tighten using a Phillips Screwdriver.
(G)
(I)
(G)
(B)
Assemble in location for intended use.
SAFETY NOTICE
Boxes MUST be secured to Frame using Screws.

Page 4 of 7
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 3: Carefully insert X Box (H) into middle compartment in Frame (G). Orient Box with label(s)
facing down toward Legs on Frame. Insert LARGE SCREWS (B) through hole in pre-installed Tabs
mounted onto Frame. Fully tighten using a Phillips Screwdriver.
(B)
(B)
STEP 4: Carefully insert remaining Grid Box (I) into lower compartment in Frame (G). Orient Box with
label(s) facing down toward Legs on Frame. Insert LARGE SCREWS (B) through hole in pre-installed
Tabs mounted onto Frame. Fully tighten using a Phillips Screwdriver.
(I)
(G)
(G)
(H)
Assemble in location for intended use.

Page 5 of 7
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 5: Complete assembly by securing each Box (H, I) to Frame (G) by inserting SMALL SCREW
(A) through hole in Corner Bracket and tightening into back of Box with a Phillips Screwdriver.
Assemble in location for intended use.
SAFETY NOTICE
Boxes MUST be secured to Frame using Screws.

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 6 of 7
A
B
C
D
Screws
Expansion Bolts
Wall Brackets
Retention Belts
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
Wall Anchoring / Anti-Tip Hardware Installation
NOTICE
Optimal protection against a
dangerous tip-over accident
provided when Bracket is
anchored to a WALL STUD.
WALL STUD: Center Wall Bracket (C) on stud and attach using Screw (A). Thread Retention Belt (D)
through Frame Bracket and hole in Wall Bracket then lace and lock Retention Belt.
OPEN DRYWALL: Mark wall for Wall Bracket and use an Expansion Bolt (B) to secure. (Detailed
instructions for installing Expansion Bolt on page 7). Thread Retention Belt (D) through Frame Bracket
and hole in Wall Bracket then lace and lock Retention Belt.
(C)
(A)
(D)
(B) Wall
Stud

Drywall
3/8” Drill Bit
(B)
Teeth
(B)
Barrel
Create Pilot Hole Tap in Bolt until teeth sink into wall surface.
Turn screw clockwise until it begins to slip. Back out and completely remove screw.
Place Screw through Bracket, replace.
12
34
INSTALLING EXPANSION BOLTS
Page 7 of 7
Customer Service: 800-367-2810
Online: www.ballarddesigns.com