Beckman Coulter Optima L Series User manual

LL-IM-12
Optima™L Series
Preparative Ultracentrifuges

Symbol
Symbol
Symbole
Símbolo
Title / Titel / Titre / Titulo / Titolo /
Dangerous voltage
Gefährliche elektrische Spannung
Courant haute tension
Voltaje peligroso
Pericolo: alta tensione
Attention, consult accompanying documents
Achtung! Begleitpapiere beachten!
Attention, consulter les documents joints
Atención, consulte los documentos adjuntos
Attenzione: consultare le informazioni allegate
On (power)
Ein (Netzverbindung)
Marche (mise sous tension)
Encendido
Acceso (sotto tensione)
Off (power)
Aus (Netzverbindung)
Arrêt (mise hors tension)
Apagado
Spento (fuori tensione)
Protective earth (ground)
Schutzleiteranschluß
Liaison à la terre
Puesta a tierra de protección
Collegamento di protezione a terra
Earth (ground)
Erde
Terre
Tierra
Scarica a terra
!
/
Simbolo

SAFETY NOTICE
This safety notice summarizes information basic to the safe operation of the equipment
described in this manual. The international symbol displayed above is a reminder that all
safety instructions should be read and understood before installation, operation, mainte-
nance, or repair of this instrument. When you see the symbol on other pages, pay special
attention to the safety information presented. Observance of safety precautions will also
help to avoid actions that could damage or adversely affect the performance of the
equipment.
Other symbols may also be displayed on the equipment. These are reproduced and
described under CONVENTIONS below and on the inside of the front cover.
Safety During Installation and/or Maintenance
This instrument is designed to be installed by a Beckman Coulter Field Service
representative. Installation by anyone other than authorized Beckman Coulter personnel
invalidates any warranty covering the instrument. Also, should the instrument need to be
moved, a Beckman Coulter Field Service representative must reinstall and relevel the
instrument in its new location.
Any servicing of this equipment that requires removal of any covers can expose parts
which involve the risk of electric shock or personal injury. Make sure that the power
switch is turned off and the instrument is disconnected from the main power source,
and refer such servicing to qualified personnel.
Do not replace any centrifuge components with parts not specified for use on this
instrument.
Electrical Safety
To reduce the risk of electrical shock, this instrument uses a three-wire electrical cord and
plug to connect this equipment to earth-ground. Make sure that the matching wall outlet
receptacle is properly wired and earth-grounded.
Do not place containers holding liquid on or near the chamber door. If they spill, liquid
may get into the instrument and damage electrical or mechanical components.
Safety Against Risk of Fire
Fuses protect certain electrical circuits within this instrument against overcurrent condi-
tions. For continued protection against the risk of fire, replace only with the same type and
rating specified.
!

This instrument is not designed for use with materials capable of developing flammable
or explosive vapors. Do not centrifuge such materials (for example, chloroform or ethyl
alcohol) in this instrument nor handle or store them near the centrifuge.
Mechanical Safety
For safe operation of the equipment, observe the following:
• Use only the Beckman Coulter rotors and accessories designed for use in this
instrument.
• Do not exceed the maximum rated speed of the rotor in use.
• NEVER attempt to slow or stop a rotor by hand.
• Do not move the centrifuge while the drive motor is spinning.
• In the event of a power failure, do not attempt to retrieve the sample from the instru-
ment for at least one hour. Then follow the instructions for recovery of the sample
under TROUBLESHOOTING AND MAINTENANCE.
Chemical and Biological Safety
Normal operation may involve the use of solutions and test samples that are pathogenic,
toxic, or radioactive. Such materials should not be used in this instrument, however, unless
all necessary safety precautions are taken.
• Handle body fluids with care because they can transmit disease. No known test offers
complete assurance that they are free of micro-organisms. Some of the most virulent—
Hepatitis (B and C) and HIV (I-V) viruses, atypical mycobacterium, and certain
systemic fungi—further emphasize the need for aerosol protection. Handle other infec-
tious samples according to good laboratory procedures and methods to prevent spread
of disease. Because spills may generate aerosols, observe proper safety precautions for
aerosol containment. Do not run toxic, pathogenic, or radioactive materials in a rotor
without taking appropriate safety precautions. Biosafe containment should be used
when Risk Group II materials (as identified in the World Health Organization Labora-
tory Biosafety Manual) are handled; materials of a higher group require more than one
level of protection.
• Dispose of all waste solutions according to appropriate environmental health and safety
guidelines.
It is your responsibility to decontaminate the instrument and accessories before
requesting service by Beckman Coulter Field Service.

LL-IM-12
August 2009
Instruction Manual
© 2009 Beckman Coulter, Inc.
Printed in the U.S.A.

Contents
iii
Page
INTRODUCTION
Instrument Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Scope of Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Radio Inteterference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Recycling Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Preinstallation Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
SECTION 1: DESCRIPTION
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Key Switch Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Run Status Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Diagnostic Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Rotor Chamber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Vacuum System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Temperature Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Temperature Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Overspeed System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Rotor Energy System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Name Rating Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

iv
Contents
Page
SECTION 2: RUN PREPARATION
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Key Switch Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Standard Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Parameter Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Programmed Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Activation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Delayed Start Program Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Entering Program 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Running Program 0 with a Second Program . . . . . . . . . . . . . . . . 2-10
Editing Settings During the Delayed Start Run. . . . . . . . . . . . . . 2-11
SECTION 3: RUN PROCEDURE
Standard Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Repeating a Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Programmed Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Delayed Start Program Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Zonal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Acceleration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Deceleration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Unloading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Points to Remember . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
SECTION 4: TROUBLESHOOTING AND MAINTENANCE
In Case of Power Failure During the Run . . . . . . . . . . . . . . . . . . . . . . 4-1
Retrieving Your Sample. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Diagnostic Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Decontamination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Sterilization and Disinfection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Storage and Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Supply List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Warranty

Illustrations
v
Tables
Page
Figure 1-1. The Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Figure 1-2. The Rotor Chamber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Figure 2-1. Inserting the Key Into the Interlock Switch . . . . . . . . . . . . . . . . . . . . . . 2-2
Figure 4-1. Removing the Control Head Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Figure 4-2. Depressing the Latch to Loosen the Front Panel . . . . . . . . . . . . . . . . . . 4-4
Figure 4-3. Interior View of Instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Figure 4-4. Location of Diagnostic Messages on the Control Panel. . . . . . . . . . . . . 4-6
Page
Table 1-1. Run Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Table 2-1. Vacuum LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Table 4-1. Diagnostic Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Introduction
vii
INSTRUMENT CERTIFICATION
To assure full system quality, the Beckman Coulter Optima™ L series
ultracentrifuges have been manufactured in a registered ISO 9001 or
13485 facility. They have been designed and tested to be compliant
(when used with Beckman Coulter rotors) with the laboratory equip-
ment requirements of applicable regulatory agencies. Declarations of
conformity and certificates of compliance are available at
www.beckmancoulter.com.
SCOPE OF MANUAL
This manual is designed to familiarize you with the Beckman Coulter
Optima L-100K or L-90K Preparative Ultracentrifuge—its function,
specifications, operation, and routine operator care and maintenance.
• The following introductory pages contain the instrument specifica-
tions and preinstallation requirements.
• Section 1 provides a brief description of the instrument, the
operating controls, and indicators.
• Section 2 explains how to use the control panel to enter run
parameters for standard and programmed operation.
• Section 3 covers operating procedures for both kinds of runs.
• Section 4 lists possible malfunctions, together with probable
causes and corrective actions, and maintenance procedures.
We recommend that you read this entire manual, especially the
SAFETY NOTICE and all safety-related information, before operating
or performing maintenance on this instrument.

viii
Introduction
➠NOTE
If the ultracentrifuge is used in a manner other
than specified in this manual, the safety and
performance of this instrument could be
impaired. Further, the use of any equipment
other than that intended for use by Beckman
Coulter has not been evaluated for safety. Use of
any equipment not specifically recommended in
this manual is the sole responsibility of the user.
CONVENTIONS
NOTES, CAUTIONS, AND WARNINGS
Certain symbols are used throughout this manual to call attention to
safety-related and other important information. The symbols used and
their definitions are as follows:
➠NOTE
Used to call attention to important information
that should be followed during installation, use,
and/or servicing of this equipment.
!CAUTION
Used to indicate a potentially hazardous situa-
tion which, if not avoided, may result in minor or
moderate injury and/or mechanical damage. It
is also used to alert against unsafe practices.
!WARNING
Used whenever an action or condition may
potentially cause serious personal injury or
loss of life. Mechanical damage may also
result.

ix
Introduction
WARNING
Indicates high voltage or risk of electric
shock. Refer servicing of all areas displaying
this symbol to service personnel.
TYPOGRAPHIC CONVENTIONS
Certain typographic conventions are used throughout this manual to
distinguish names of user interface components, such as keys and
displays.
•Key names (for example, [START] or [ENTER/RECALL]) appear in
capital letters within brackets.
•Display names (for example, TEMP°C or SPEED-RPM) appear
in bold type.
RADIO INTERFERENCE
This instrument has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with this instruction manual, may cause interference to radio
communications. Operation of this equipment in a residential area
may cause interference, in which case the user will be required to
correct the interference at his or her own expense.

x
Introduction
CANADIAN REGULATIONS
This digital apparatus does not exceed the Class A limits for radio
noise emissions from digital apparatus as set out in the radio interfer-
ence regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de Classe
A prescrites dans le reglement sur le brouillage radioelectrique édicté
par le Ministère des Communications du Canada.
RECYCLING LABEL
This symbol is required in accordance with the Waste Electrical and
Electronic Equipment (WEEE) Directive of the European Union. The
presence of this marking on the product indicates
1) the device was put on the European market after August 13, 2005
and
2) the device is not to be disposed via the municipal waste collection
system of any member state of the European Union.
It is very important that customers understand and follow all laws
regarding the proper decontamination and safe disposal of electrical
equipment. For Beckman Coulter products bearing this label please
contact your dealer or local Beckman Coulter office for details on the
take back program that will facilitate the proper collection, treatment,
recovery, recycling and safe disposal of the device.
A28219-AA

xi
Introduction
SPECIFICATIONS
CONTROL CHARACTERISTICS
Only values with tolerances or limits are guaranteed data. Values
without tolerances are informative data, without guarantee.
Speed
Set speed . . . . . . . . . . . . . . . 1000 rpm to maximum speed*in increments of 100 rpm
Speed control. . . . . . . . . . . . Actual rotor speed will be ±20 rpm of the set speed (above 1000 rpm)
Speed display. . . . . . . . . . . . Indicates rotor speed in increments of 10 rpm at speeds below
1000 rpm, and increments of 100 rpm at speed above 1000 rpm
Time
Set time . . . . . . . . . . . . . . . . Up to 99 hours and 59 minutes; HOLD for runs of unspecified length
Time display . . . . . . . . . . . . Indicates time remaining in timed runs, time elapsed in HOLD runs,
and estimated time remaining in
ω
2truns
Temperature
Set temperature . . . . . . . . . . 0 to 40°C in increments of 1°C
Temperature control . . . . . . ±0.5°C of set temperature
Temperature display . . . . . . Indicates rotor temperature in increments of 0.1°C
Temperature stability. . . . . . Within 0.3°C of set after equilibration
Ambient temperature
range. . . . . . . . . . . . . . . . 15 to 40°C
STOP
VACUUM—
µ
SPEED—RPM TIME—HR:MIN TEMP—°C
POWER OFF
X 10,000
SAVE
PROG
HOLD
w
2
t
DECEL
ACCEL
VACUUM
START
STOP
TIME
TEMP
CE
0
123
456
789
SPEED
ENTER/RECALL
*Maximum speed will be 100 000 rpm or 90 000 rpm for the current models. Models purchased earlier may include maximum speeds of 80 000,
70 000, or 60 000 rpm.

xii
Introduction
ω
2tIntegrator
Set
ω
2t. . . . . . . . . . . . . . . . . Up to 9.99 ×1014 radians squared per second
ω
2tdisplay. . . . . . . . . . . . . . Shows accumulated centrifugal force to three significant digits (in
exponential notation)
Acceleration . . . . . . . . . . . . . . . Selection from two profiles: maximum acceleration from 0 rpm to set
speed, or slow acceleration from 0 to 500 rpm, followed by maximum
acceleration to set speed
Deceleration . . . . . . . . . . . . . . . Selection from three profiles: full dynamic braking to 0 rpm, slow
(full brake to 500 rpm followed by reduced braking to a gentle stop),
or no brake
Operation . . . . . . . . . . . . . . . . . Standard, programmed, or delayed start; instrument memory can store
up to nine programs
Key Switch . . . . . . . . . . . . . . . . Used to select normal or zonal operation
OPERATIONAL FEATURES
Revolution Counter. . . . . . . . . . Displays accumulated total number of rotor revolutions in tens of
thousands
Barrier Ring . . . . . . . . . . . . . . . 41-mm (1.63-in.) heat-treated steel alloy armor ring surrounded by a
12-mm (0.50-in.) steel vacuum chamber to provide full protection for
the operator
Door . . . . . . . . . . . . . . . . . . . . . 17.5-mm (0.69-in.) high-strength structural steel
Vacuum. . . . . . . . . . . . . . . . . . . Diffusion pump in series with a mechanical pump typically reduces
chamber pressure to below 5 microns (0.7 Pa)
Instrument Classification . . . . . S (uses all Beckman Coulter preparative rotors except Types 35 and
42.1 rotors with serial numbers 1299 or lower)
Diagnostic Messages . . . . . . . . See Section 4: TROUBLESHOOTING AND MAINTENANCE
➠NOTE
The Optima L series ultracentrifuges have been
designed and tested to operate safely indoors at
altitudes up to 2 000 m (6 562 ft).

xiii
Introduction
PHYSICAL DATA
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465 kg (1025 lb)
Height (overall) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120.7 cm (47.5 in.)
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94.0 cm (37 in.)
Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67.3 cm (26.5 in.)
Ventilation clearances . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 cm (2 in.) sides;
15.2 cm (6 in.) rear
Finishes
Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . coated polycarbonate
Top surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .urethane paint
Other surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . acrylic baking enamel
Maximum heat dissipation into the room . . . . . . . . . . 1.0 kW (3400 Btu/hr)
Humidity restrictions . . . . . . . . . . . . . . . . . . . . . . <95% (non-condensing)
Noise level measured 0.91 m (3 ft) in front of the instrument . . . . . <57 dBa
Installation (overvoltage) category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II
Pollution degree. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2†
PREINSTALLATION REQUIREMENTS
!CAUTION
Do not attempt to install or turn on the power
to the instrument. Its purchase price includes
installation by Beckman Coulter personnel.
Installation by anyone other than authorized
Beckman Coulter personnel invalidates the
warranty.
Preinstallation requirements have been sent prior to shipment of the
instrument. (Copies are also attached to the outside of the shipping
container.) The following information is provided in case the ultra-
centrifuge must be relocated. Contact your Beckman Coulter Field
Service representative to adjust and level the instrument if it must be
moved.
†Normally only nonconductive pollution occurs; occasionally, however, a temporary conductivity caused by condensation must be expected.

xiv
Introduction
ELECTRICAL DATA
Instrument rating: 220 to 240 VAC, 50 Hz, 20 A
200 to 240 VAC, 50/60 Hz, 20 A
Power line range: 180 to 264 VAC, 60 or 50 Hz (single-phase), 30 A
Electrical supply: Class I
To reduce the risk of electrical shock, this equipment uses a three-
wire electrical cord (1.8 m; 6 ft) and plug to connect the equipment
to earthground. In regions where the instrument is supplied with an
unterminated cord, a plug that meets local electrical and safety
requirements must be supplied. (Contact your local Beckman Coulter
office for specific information regarding these requirements.) See the
Table below for the required wire connections. Make sure that the
matching wall outlet receptacle is properly wired and earth-grounded.
Required Wire Connections
Wire Insulation
Color Terminal
Symbol
Harmonized North American
Green/Yellow Earth ground
Light Blue Neutral N L
Brown Live or Line L L
Measured
Line Voltage
Wall Outlet:
Hubbell 9330,
Bryant 96-30-FR,
or Equivalent
(NEMA 6-30 R)
30-ampere
Circuit
Protector
Earth
Ground North
American
Plug
30-ampere
Circuit
Protector

xv
Introduction
To ensure safety, the instrument should be wired to a remote emer-
gency switch (preferably outside the room where the centrifuge is
housed, or adjacent to the exit from that room), in order to disconnect
the instrument from the main power source in case of a malfunction.
Optima L series ultracentrifuges have been designed and tested to
operate safely indoors at altitudes up to 2000 m (6562 ft).
SPACE
Locate the Optima L in a clean, safe, uncluttered environment.
Be sure to provide a 5.1-cm (2-in.) clearance on each side, as the
feet extend about 5.1 cm (2 in.) beyond the instrument (see the Figure
below). (The pads under each foot have been designed to prevent
possible rotation of the instrument in the event of a rotor mishap.) A
15.2-cm (6-in.) clearance is required at the rear of the instrument for
servicing the control panel and to ensure sufficient air ventilation
during operation. The ultracentrifuge must have adequate air ventila-
tion to ensure compliance to local requirements for vapors produced
during operation.
The instrument will operate within specifications in a laboratory with
ambient temperatures ranging from 15 to 40°C.
!WARNING
Do not place the instrument near areas
containing flammable reagents or
combustible fluids.
cm
in.
94.0
37
5.1
2
5.1
2
67.3
26.5
15.2
6

xvi
Introduction
BIO-SAFETY LEVEL 3 INSTALLATION
For laboratories with epoxy aggregate floors, such as BSL-3 labs, a
non-invasive installation kit (PN 393862) is available. The kit, which
consists of a high-strength adhesive tape, is CSA certified for use on
epoxy aggregate floors only.