Bosch Rexroth VCH 08.1 User manual

Bosch Rexroth AG
Electric Drives and Controls
Bgm.-Dr.-Nebel-Str. 2
97816 Lohr am Main, Germany
Phone [phone]
Fax [phone]
www.boschrexroth.com
Rexroth IndraControl VCH 08.1
with Emergency STOP Button
Hand-Held Terminal
Assembly Instruction

About this Document
The assembly instructions describe how to install a VCH 08.1 with EMER-
GENCY STOP button.
For further information, please refer to the project planning manual
“Rexroth IndraControl VCH 08.1”, parts number R911320190.
Symbols
This document uses the following symbols to draw the reader’s attention to
notices and dangers:
Target Group
All installation work related to the automation system may only be carried
out by qualified personnel (e.g. electricity specialists, electrical engineers).
The personnel installing the device must be qualified to work with the auto-
mation system.
Safety Component according to Machinery Directive
This device is a safety component or part of the safety circuit! Please read
and comply with the safety instructions specified in the respective manual
before installing and setting the device up.
Comply with the regulations of the Machinery Directive 2006/42/EC. Recon-
cile the safety components to the EN ISO 13849-1, EN ISO 13850 standards.
A risk assessment according to EN ISO 14121-1 determines the safety cate-
gory (see EN 60204-1). Check whether further standards must be complied
with.
The present instructions apply for the following device variant:
Device type Description Parts number
VCH08.1EAB-064ET-A1D-064-FS-B2-PW VCH08.1 with enabling button, override,
emergency stop button, short cable
R911172138
2/4 R911333152-AA_BPZ_DOC
20. Dezember 2010

Unpacking
s and check the contents for visible damages in transit. Also
the delivery corresponds to the data on the delivery note.
Unpack all item
check, whether
Please contact the Bosch Rexroth sales department immediately when notic-
ing discrepancies or damages in transit.
Connecting
ndraControl VCH 08.1 hand-held terminal is connected to the automa-
ase ensure that the STOP button is NOT pressed prior to com-
The I
tion system via the IndraControl VAC 30.2 connection module. The operator
has to ensure that the system, in particular the safety devices, are in a
proper condition before commissioning the IndraControl VCH 08.1. The sys-
tem and the safety devices are to be checked in regular intervals during the
operation.
Ple
missioning the IndraControl VCH 08.1.
Connecting the IndraControl VCH 08.1 with pressed STOP button
results in a system shut-down.
3/4 R911333152-AA_BPZ_DOC
20. Dezember 2010

4/4 R911333152-AA_BPZ_DOC
20. Dezember 2010
inal or the short-circuit connector!
To conne Control VCH 08.1, unscrew the short-circuit connector
om the VAC 31.1 and put the bayonet connector effortlessly on the bayo-
as to be screwed on
CH 08. cted to the VAC
0.2 connection module via an extension cable of type RKS.
Please make sure that the plant is in safe state during plugging in
and removing the hand-held term
If the hand-held terminal or the short-circuit connector are not con-
nected, the safety-circuits of the VAC 31.1 connection module are
open. Plugging in or removing the hand-held terminal or short-
circuit connector during a running operation results in a system
shutdown.
ct the Indra
fr
net flange of the IndraControl VAC 31.1 connection module.
Please make sure that the position of the keyway connection is correct. Only
if the connector engages properly, the correct position is reached. Now turn
the knurled nut on the flange until the nut engages.
To ensure an optimal connection of the contacts and to attain the
specified protection class, the knurled nut h
until the bayonet mechanism engages completely.
1 device variants with short cable have to be conne V
3