Bradley S19-300T User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
215-1308 Rev. F; ECN 17-05-045
© 2017 Bradley
Page 1 of 8 6/5/2017
S19-300T (top supply)
S19-300B (bottom supply)
Heat Trace Combination Drench
Shower and Eyewash Unit Class 1,
Div. 1, Groups C & D
(includes 120 V and 220/240 V
versions)
Table of Contents
Pre-Installation Information ..................2-3
Assembly of Components .....................4
Installation ...............................5–6
Repair Parts List ..........................6–7
Troubleshooting .............................8

2
S19-300T, S19-300B—Class 1, Div. 1, Groups C & D Installation
6/5/2017 Bradley • 215-1308 Rev. F; ECN 17-05-045
WARNING
Flush the water supply lines before beginning installation and after installation is complete. Test
the unit for leaks and adequate water flow.
Main water supply to the unit should be "ON" at all times unless system is being serviced.
Provisions shall be made to prevent unauthorized shutoff.
Power supplied to the unit should be 120VAC or 220-240VAC, 50-60 Hz, 15 amp branch circuit with
a dedicated circuit breaker or fuse and should not supply power to any other device. Compliance
and conformity to local codes and ordinances is the responsibility of the installer.
Do not use this safety equipment in a location that does not match its hazardous location rating.
Verify the appropriate ratings prior to installation.
When making electrical connections be sure to follow all lockout-tagout safety procedures.
CAUTION
Emergency equipment must be supplied with tepid water (60-100°F/15.6-37.8°C). Any prolonged
exposure to near freezing water affects the body's ability to maintain body temperature, increasing
the risk of hypothermia.
The unit must be supplied with clean, potable water.
NOTICE
Before installing this product ensure that there are adequate clearances around the product and
activation of the product does not interfere with other products or obstructions.
It is recommended that all water supply and electrical connections be made at temperatures above
freezing. Failure to do so may result in major product and/or property damage.
Constant power supply to the safety equipment is necessary for it to function.
Avoid cleaners containing organic solvents, alcohols and hydrocarbons. Rinse with potable water
after cleaning.

3
Installation S19-300T, S19-300B—Class 1, Div. 1, Groups C & D
Bradley • 215-1308 Rev. F; ECN 17-05-045 6/5/2017
IMPORTANT
The installation and location of all safety drench showers, eye and eye/face washes must comply
with the requirements of ANSI/ISEA Z358.1.
Read this installation manual completely to ensure proper installation, then file it with the owner
or maintenance department. Compliance and conformity to local codes and ordinances is the
responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before discarding any
packaging material. If any parts are missing, do not begin installation until you obtain the missing
parts.
Installation and maintenance of this system must be completed by a qualified plumber and
electrician according to the information contained in this installation manual and in compliance
with all national and local codes.
The ANSI/ISEA Z358.1 standard requires an uninterrupted supply of flushing fluid. Bradley
plumbed emergency fixtures require a minimum of 30 PSI (0.21MPa) flowing pressure. Flushing
should be tepid per ANSI Z358.1
Weekly activation must be conducted on all plumbed emergency equipment to ensure a suitable
flushing fluid supply is present and any sediment build up in the supply line is cleared. Inspect
safety equipment monthly to address any maintenance issues ensuring the equipment is in good
operating condition and that there are no signs of wear.
Perform functional test upon relocation of safety equipment.
The inspection and testing results of this equipment should be recorded weekly to verify proper
operation. This equipment should be inspected annually to enure compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be trained
regarding the placement and proper operation of emergency equipment per ANSI/ISEA Z358.1.
For questions regarding the operation or installation of this product, visit www.bradleycorp.com or
call 800-BRADLEY (272.3539).
Product warranties and parts information may also be found under ”Products” on our web site at
bradleycorp.com.

4
S19-300T, S19-300B—Class 1, Div. 1, Groups C & D Installation
6/5/2017 Bradley • 215-1308 Rev. F; ECN 17-05-045
Components
P.O. BOX 309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX: [phone])
http://www.bradleycorp.com
114-052
Signed
Signed
Signed
Date
Date
Date
Signed
Unterschrift
Signe
Date
Datum
Date
P.O. Box 309, Menomonee Falls,WI 53051
R
TESTTHIS UNIT EACH WEEK
Test-operatevalve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
DIESES GERÄT 1STWÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chosequi ne va pas fait
un rapport immédiatement.
Prepack S45-1535
Safety Sign
114-052 (qty. 2)
Hook
151-001 (qty. 2)
Emergency Tag
204-421
Hex Nut #10-24
151-001 (qty. 2)
Screw #10-24 x 1/2"
160-245 (qty. 2)
Pull Rod
128-156G
Eye/Face Wash
Assembly
Option
S05-153
Stainless Steel
Showerhead
Plastic
Showerhead
Eyewash
Assembly
Option
S05-171
Heat Trace Unit—Class 1, Div. 1, Groups C & D
S19-300T (top supply)
S19-300B (bottom supply)
11.1
11.12
11.11
12
11

5
Installation S19-300T, S19-300B—Class 1, Div. 1, Groups C & D
Bradley • 215-1308 Rev. F; ECN 17-05-045 6/5/2017
Supplies Required
• (3)
3⁄8" floor anchors and bolts
• Teflon tape and pipe sealant
• Piping to 1¼" NPT water supply inlet on unit with
adequate supply pipe supports
• Minimum 4" drain to accommodate 30 gallons
per minute discharge for drench shower waste
• Electrical supplies to connect to unit junction box
NOTICE! Bottom supply units have provisions for
supporting the top of the unit. The 1-1/4" NPT
solid pipe protruding from the shell must be
used to support the unit.
Secure unit to floor
1. Install three suitable anchors (supplied by
installer) for 3⁄8" bolts in the floor.
2. Bolt the base to the floor anchors using 3⁄8"
bolts (supplied by installer).
3. Install the pull rod to the unit as shown.
NOTICE! Do not rely on unit to support supply piping.
WARNING! Unit requires a minimum 30 GPM to operate
and a minimum 30 PSI of flowing water
pressure. Preferred flowing water pressure is
40–60 PSI. Water supply to the unit must be
freeze-protected (by others).
NOTICE! Pipe size should be no smaller than 1¼"
(supplied by installer).
Connect water supply
1. Connect the water supply piping to the 1¼"
NPT inlet on the unit (piping by installer).
Use pipe hangers or other means to provide
adequate supports for the supply pipe
(supports by installer).
2 Open water supply lines and test for leaks
and adequate water flow.
Assemble components
1. Install the showerhead to the unit as shown. The
bottom edge of the showerhead should be 85¼"
(2165mm) from the floor.
2. Mount the safety signs to the wall or to the unit if
desired. Use the screws, nuts and hooks provided to
hang the signs back-to-back on the unit.
Connect electrical supply
1. Connect the power to the junction box on the unit
as shown in the schematic on page 4 (junction box
accepts ¾" NPT conduit fittings).
2. Connect the optional alarm system and indicator light
as shown.
NOTE: Average power consumption of the unit is .7 amp/80 watts
at 120VAC (.35 amp/80 watts at 220/240 vac) at 50°F (10°C)
internal unit temperature. Refer to the installation instructions
provided with the alarm system for more information.
Ø 9" (229mm) Flange with
(3) Ø3⁄8" (10mm) Holes on
a Ø8" (203mm) Bolt Circle
Bottom Supply
1¼" NPT
Top Supply
1¼" NPT
Junction Box
¾" NPT Hub
6"
(152mm)
43"
(1089mm) 39½"
(1004mm)
60¾"
(1543mm)
85¼"
(2165mm)
1017⁄8"
(2588mm)
35½"
(900mm)
68"
(1724mm)
25¾"
(654mm)
37¾"
(959mm)
92"
(2337mm)
19¼"
(489mm)
(245mm)
9¾"
Use teflon tape
only with plastic
showerheads.
Bottom supply units must use
this pipe for supporting unit.
Safety signs
shown mounted
back-to-back.
¾" NPT
Junction Box
opening
CAUTION Any electrical components supplied by
installer must match the rating of the
fixture to maintain its integrity.
Unit is provided with sealing compound and conduit seals.
Seals must be filled by installer prior to powering the unit per
seal manufacturer's instructions.

6
S19-300T, S19-300B—Class 1, Div. 1, Groups C & D Installation
6/5/2017 Bradley • 215-1308 Rev. F; ECN 17-05-045
Optional Alarm System Amber Lamp = Heater ON
Green Lamp = Power TO UNIT
Indicator
Light
Option
Black
Green
Green
White
Black
Power
Supply
Ground Screw-in
Junction Box
Heat Trace
Cable
Thermostat
White
G
A
Terminal
Block
Alarm
System
Option
Butt
Splice
White
Black
Green
Red
Red
Black
Green
Item Part No. Qty. Description
1 131-059 1 Base
2 219-040 1 Shell - Lower Left
3 219-030 1 Shell - Lower Right
4 219-027 1 Shell - Upper Left
5 219-041 1 Shell - Upper Right
6 269-1292 as req’d. Edge Trim
9 269-1551 1 Thermostat
10 S45-1535 1 Hardware Prepack
Plastic Showerhead (refer to page 2)
11 S24-188 1 Plastic Showerhead
11.1 S24-193 1 Shroud Assembly
11.11 187-053 1 Showerhead Shell
11.12 154-147 1 Ring
Stainless Steel Showerhead (refer to page 2)
12 S24-191 1 Stainless Steel Showerhead Assy.
13 S27-301 1 Ball Valve, 1" with Nut
(frost-proof)
13.1 110-214 1 Nut only
14 153-489 1 Adapter
15 161-036 6 Hex Nut, 5⁄16"-18
16 128-200 1 Handle
17 S21-068 3 Operating Stem
18 128-150 1 Handle
19 142-002DC 3 Lockwasher
20 128-156G 1 Pull Rod, 26"
Item Part No. Qty. Description
21 S05-153 1 Eye/Face Wash Assembly Option
21.1 S05-152 1 Yoke, Drilled
21.2 S05-135 2 Eyewash Head
21.3 S53-063 2 Dust Cover, Tethered
21.4 113-1191 1 Stem
21.5 169-1069 1 Elbow ½" x 3⁄8"
21 S05-171 1 Eyewash Assembly Option
21.1 S05-170 1 Yoke, Drilled
21.2 107-371 2 Dust Cover, Tethered
21.3 S21-077 1 Stem
21.4 169-1069 1 Elbow Reducing ½" x 3⁄8"
22 S27-329 2 Ball Valve, ½" with Nut
(frost-proof)
22.1 110-215 2 Nut only
23 153-372R 2 Ball Valve Adapter - R. H.
24 128-151 2 Handle Adapter
25 S08-383 2 Flag Handle - R.H. Assembly
25.1 114-049 2 Handle Label
26 269-1296 2 Hose Barb
27 S89-025 1 Hose
28 S45-1703 1 Valve, Freeze-Protect
29 S45-1702 1 Valve, Scald-Protect
30 269-1285 as req’d. Rubber Tubing
31 124-048 1 Washer

7
Installation S19-300T, S19-300B—Class 1, Div. 1, Groups C & D
Bradley • 215-1308 Rev. F; ECN 17-05-045 6/5/2017
4
11
5
10
2
3
1
23 24
17
25, 25.1
22.1
15
19
23
27
24
17
25, 25.1
22 22.1
15
15
19
28
26
30
26
30
29
21.1
21.2
21.3
21.4
21.5
21.1
21.2
21.3
21.4
29
26
30
9
6
28
7
18
13
14
20
16
15
15
19
13.1
17
31
Pull Rod
Assembly
Eye/Face
Wash
Option
Flag
Handle
Optional
Drench Hose
Freeze and
Optional Scald
Valve (for top
supply)
NOTE: Specify
required length
for Item 30
when ordering.
Optional Freeze and
Scald Valve
(for bottom supply)
NOTE: Specify required
length for Item 30 when
ordering.
Junction Box and Thermostat
(Item 9) apply to both top and
bottom supplies.
Eyewash
Option
Specify required
length when ordering
Flow control
this end

8
S19-300T, S19-300B—Class 1, Div. 1, Groups C & D Installation
6/5/2017 Bradley • 215-1308 Rev. F; ECN 17-05-045
Problem Cause Solution
Low water flow at drench
shower and eyewash
Insufficient pressure
Undersized supply piping
Minimum 30 GPM required
Increase pressure/pipe size
Low water flow at drench
shower or eye wash
Debris in system Disassemble the showerhead, clean and reassemble
Unscrew the eyewash heads from the yoke, clean and
reassemble. If still clogged, replace the heads.
Freeze-protection valve is
flowing water
Power supply is off [if the
water temperature from the
valve is below 45°F (7°C)]
Turn the power on.
Water supply is too cold Make sure the unit is supplied with tempered water.
Defective thermostat [if the
water temperature from the
valve is below 45°F (7°C)]
Check continuity and replace if check fails activates at 50°F
(10°C) (factory-set).
Defective freeze valve [if the
water temperature from the
valve is above 45°F (7°C)]
Replace the freeze valve
NOTE: A water supply that is at least 45°F (7°C) or colder will
hold the freeze bleed valve open. To close the valve:
1. turn the water off temporarily or plug the valve until the
heat trace unit’s heat warms the valve
2. increase the surface temperature of the valve to above
45°F (7°C) by immersing the valve in hot water
IMPORTANT: Make sure that the heat trace unit is
operating properly before plugging the freeze bleed valve.
A plugged valve will not provide backup freeze protection
should the heat trace unit fail.
Scald-protection valve is
flowing water
Defective scald valve [if the
water temperature from the
valve is below 80°F (27°C)]
Replace the scald valve.
Direct sunlight or high
ambient temperature
Cool the unit.
Defective thermostat Check continuity and replace if check fails activates at 50°F
(10°C) (factory-set).