BROSA Edgar Dresser User manual

ASSEMBLY GUIDE
Edgar Dresser
v1.0

Components
Upon unpacking your dresser from it’s delivery box, you should have the
separate pieces shown below. Follow the steps on the next pages to assemble
your new dresser.
Outer body of dresser
Draws
Base x 1 Side panel x 2
Support beam x 2
Base large x 2
Base small x 2
Support beam x 2
Leg x 4
Middle panel x 1
Front panel small x 2
Front panel large x 2
Top panel x 1
Back panel x 2
Back panel large x 2
Back panel small x 2
Side panel x 8

Hardware
You will need

Step 1 Insert a dowel (B) in both of the inner holes of the
support beam (1) and a cam screw (C) in the two outer
holes. Align the front support beam perpendicular to
the support beam (2) and rmly press together. Insert a
cam lock (E) in both of the holes on the support beam
(1) as shown in the diagram. Repeat the same process
for the other support beam.
B
E
C
B x 4
C x 4
E x 4

BK
E
C
Step 2
B x 8
C x 8
E x 8
K x 1
2.1 Insert a dowel (B) into both inner holes of the
support beam a cam screw (C) into both holes on the
outside. Dab some glue (K) onto the end of the support
beam. Align the support beam and side panel together
as shown in the diagram and press together. Insert a
cam lock (E) into the hole as shown in the diagram.
2.2 Repeat the same process for the other side panel.
Step 2.2
Step 2.1
B
K
E
C

Step 3 3.1 Insert dowels (B) into each of the four inner holes
on the base and cam screws (C) into the outer holes.
3.2 Align the structure formed in Step 2 to the base and
rmly press together. On the inside of the structure
insert a cam lock (E) into each of the four holes as
shown in the diagram.
B x 4
C x 4
E x 4
E
C
B
Step 3.1
Step 3.2

P
H
G
G
A
Step 4
A x 3
G x 18
H x 6
P x 3
4.1 Align one part of the back panel to the the structure
making sure the holes are facing upward and gently
slide along the grooves down to the base. Insert a
dowel (A) in each of the three holes on the top of the
rst back panel. Align the second half of the back panel
to the structure with the holes facing downward and
gently slide along the grooves, rmly pressing together
both of the back panels.
4.2 Align a track (P) to the inner side panel at an
interval and x into place using screws (G & H).
Repeat the same process for the remaining tracks (P).
Step 4.2
Step 4.1

Step 5
Step 6
Insert a dowel (B) into the inner hole along the bottom
of the middle panel and a cam screw (C) into the outer
hole. Align the middle panel inside the top tier of the
structure and rmly press the middle panel to the top
support beam. Insert a cam lock (E) into the hole as
shown in the diagram.
Align a track (P) to the middle panel and x into place
using screws (G & H).
B x 1
C x 1
E x 1
G x 6
H x 2
P x 1
B
C
E
P
H
G
G

Step 7 Insert a dowel (B) into each of the inner holes along the
top panel and a cam screw (C) into each of the outer
holes. Align the top panel to the structure and rmly
press together. Insert a cam lock (E) into each of the
four holes inside the structure as shown.
Step 8 Cover the cam locks (E) inside the structure with a
plastic cap (R). Insert a dowel (B) into the top of the leg
and align it to the underside of the base. Press the leg
rmly in place and using the allen key (J) to tighten the
bolt on the bottom of the leg until secure. Peel o the
paper to reveal the adhesive on the plastic cover (S)
and place it on the bottom of the leg. Repeat the same
process for the other legs.
B x 6
C x 6
E x 6
B x 4
J x 1
R x 4
S x 4
BC
E
R
B
J
S

Step 9 Align a track (Q) to a side panel for a draw and x into
place with screws (H). Repeat the same process for the
remaining side panels for the draws. Insert a dowel (A)
into the middle hole on the end of each panel.
Step 10 Insert a dowel (A) into the middle hole on either side of
the back side panel of the draw. Align the side panel to
the back and rmly press together. Insert a screw (I)
into both holes and screw tightly using a phillips head
screwdriver. Repeat for the other side panel.
Repeat process for the remaining draws.
A
Q
H
A x 4
H x 24
Q x 4
A x 8
I x 16
A
I
A
I