Cisco TelePresence SX10 User manual

Cisco TelePresence
SX10 Quick Set
INSTALLATION GUIDE
78-100213-04A0 | JUNE 2018
© 2018 Cisco Systems, Inc. All rights reserved.

This package contains
Accessories (ordered separately):
• Cisco Touch 10 controller
• VESA screen mounting kit
• VGA presentation cable (8m/ 26.2ft)
• HDMI presentation cable (8m/26.2ft)
• Cisco table microphone
Cisco TelePresence
SX10 Quick Set
Bracket for wall mounting LAN cable (5 m/ 16.4 ft)
Cisco TelePresence
TRC6 remote control and
2× AAA batteries
HDMI monitor cable
(2 m /6.6 ft)
Power adapter and power
cable (1.8m / 5.9ft)

H
D
130 - 145 cm
4ft3in.-4ft9in.
1. Before mounting the SX10
Mount the screen
For the best conferencing experience,
mount the screen at 130-145 cm
(4 ft 3 in.- 4 ft 9 in.) height.
For pre-installed and larger screens,
placing the SX10 under the screen
may work better. Connect the cables,
and set the device on a table or a shelf
under the screen to check the image
before wall mounting the SX10.
Display depth D Wall mount height H
<100 mm
<3.94 in.
110 mm
4.33 in.
100 - 130mm
3.94 - 5.12 in.
130 mm
5.12 in.
130 - 150 mm
5.12 - 5.91 in.
150 mm
5.91 in.
150 - 170 mm
5.91 - 6.69in.
170mm
6.69 in.
170- 190 mm
6.69- 7.48 in.
185 mm
7. 4 8 i n .
Measure screen depth to determine the SX10 installation height
The thicker the screen, the further up from the screen you should install the SX10.
This is to ensure that the screen doesn’t block the camera view.
For more on room guidelines and recommendations for other scenarios visit:
collaborationhelp.cisco.com and www.cisco.com/go/projectworkplace

Ø 4 mm
1
3
Ø 4 mm
5
2
1
6
4
2. SX10 wall mount
This type of equipment is to be installed by the submittor’s/dealer’s qualified installer. Installer is respon-
sible for obtaining safety inspection of the structural integrity of the installation by the local authority/
inspection department.
You need:
• Drill
• 2 screws, Ø4 mm
• Level
• Tape measure
• Screwdriver
• Pencil
H

1. Connect the SX10 to your screen with the provided HDMI cable.
2. Connect the LAN cable from the SX10 to an Ethernet wall plug. If Power over
Ethernet (PoE) is available, the SX10 is powered through this cable. Alternatively
you can use a PoE injector.
3.If your network doesn’t support PoE, use the provided power adapter.
Connect additional cables for presenting, and external microphone and speakers to
their respective connectors, if needed.
Power over Ethernet (PoE)
The PoE source (network switch or PoE injector) must be located in the same building
as the SX10 device. The maximum cable length when connecting the SX10 to a PoE
source is 50 m / 164 ft.
NOTE: Do not connect an external device to the USB port.
1
2Monitor output,
HDMI
Ethernet/PoE
Power
3
3. Connect the cables

The SX10 starts up when the power is connected, and the power button’s LED lights up.
If the system doesn’t start, push the power button.
If there is a problem with the start up, the LED turns red. Please contact support for
assistance.
Make sure your monitor is turned on, and that you have selected the correct input.
Power button
and LED
5. Follow the on screen instructions for setup
Cisco Webex
If you have a Cisco Webex subscription, you can use the remote control to set it up
and the Cisco Webex Teams app to control the system.
To find more information on how to get started with Webex registered systems, visit
collaborationhelp.cisco.com and look for the Getting Started articles for room devices.
Other services
When using one of the other available services, use the remote control for the setup.
For further information on configuration, download the Getting Started Guide from
www.cisco.com/go/sx-docs.
4. The SX10 starts automatically
Cisco
Webex
Other
services
Welcome
Lorem ipsum

1 2 3
4 5 6
7 8 9
*0#
.@
pqrs tuv wxyz
defabc
ghi jkl mno
Remote control
Volume control and
Increase/Decrease control
Field selector
Cursor keys
Go back one step Mute and unmute
• Reject incoming call
• End call
• Cancel
• Back to Home screen
(outside calls)
Place call
Accept incoming call
OK/Enter
User guides
Cisco Webex
To find more information on Webex registered room devices, visit:
collaborationhelp.cisco.com
Other services
For user guides and compliance and safety information for this product, visit:
www.cisco.com/go/sx-docs

On our web site you will find an overview of the
worldwide Cisco contacts.
Go to:
https://www.cisco.com/web/siteassets/contacts
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Dr.
San Jose, CA 95134 USA
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries.
To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are
the property of their respective owners. The use of the word partner does not imply a partnership relationship between
Cisco and any other company. (1110R)