CMC Pro Series User manual

IMPORTANT INFORMATION - PLEASE READ AND SAVE
Made in USA
of US and foreign components
The Rescue and ProSeries®Rescue Harnesses are designed
for multi-purpose use in fire/rescue, industrial, and rope access
work applications. The harness’ light weight and ease of donning
and doffing appeal to emergency responders who must act
quickly. USE
Rescue and work harnesses from CMC are designed to
comfortably support the wearer, creating a safe work platform.
Because our harnesses are used when working at height, they are
also built with the strength to catch a fall.
USER INFORMATION
User Information shall be provided to the user of the product.
CMC recommends separating the User Information from the
equipment and retaining the information in a permanent record.
CMC also recommends making a copy of the information to keep
with the equipment and that the information should be referred to
before and after each use.
INSPECTION
Inspect the equipment according to your department's policy for
inspecting life safety equipment. Inspect the equipment prior to
entry into service, after each use, and at least once every 12
months. The equipment should be thoroughly inspected by an
inspector that meets your department's training standard for
inspection of life safety equipment. Keep a record of the date,
person performing the inspection and results, as well as the date
of first use, name of users and any other pertinent information
necessary to keep accurate track of the equipment’s usage history
in the equipment log or on a tag that attaches to the equipment.
Each user should be trained in equipment inspection and should
inspect the equipment before each use.
When inspecting the equipment, check the webbing and rope for
cuts, worn or frayed areas, broken fibers, soft or hard spots,
discoloration, or melted fibers. Check the stitching for pulled
threads, abrasion, or breaks. Check the hardware for damage,
sharp edges, and improper operation. If any of the above is noted,
or if the equipment has been subjected to shock loads, fall loads,
or abuse other than normal use, remove the equipment from
service and destroy it. If there is any doubt about the serviceability
of the equipment, remove the equipment from service and destroy
it.
WARNING
• FAILURE TO COMPLY WITH INSTRUCTIONS OR IMPROPER USE OF THIS
EQUIPMENT MAY RESULT IN SERIOUS INJURY OR DEATH.
• MANUFACTURER’S INSTRUCTIONS SHALL BE PROVIDED TO THE USER.
• USE, INSPECT, AND REPAIR ONLY IN ACCORDANCE WITH MANUFACTURER’S
INSTRUCTIONS.
• READ ALL OF THE ACCOMPANYING INSTRUCTIONS AND LABELS.
• THIS EQUIPMENT HAS BEEN DESIGNED AND MANUFACTURED FOR USE BY
EXPERIENCED PROFESSIONALS ONLY.
• FOLLOW RECOMMENDED PROCEDURES FOR DONNING AND ADJUSTING THE
HARNESS.
• DO NOT ATTEMPT TO USE THIS EQUIPMENT WITHOUT PROPER TRAINING.
• THE USER SHALL HAVE A RESCUE PLAN AND A MEANS TO IMPLEMENT IT WHEN
USING THIS EQUIPMENT.
• FOLLOW THE EMPLOYER’S SAFE WORKING PROCEDURES AT ALL TIMES WHEN
USING THE HARNESS.
• THE USER SHALL KNOW AND FOLLOW ALL APPLICABLE OSHA AND OTHER
REGULATIONS PERTAINING TO OCCUPATIONAL SAFETY.
• DO NOT ALTER OR MISUSE THIS EQUIPMENT.
• ASSURE THAT ANY COMBINATION OF COMPONENTS OR SUBSYSTEMS, OR
BOTH, DO NOT INTERFERE WITH THE SAFE FUNCTION OF EACH OTHER.
• DO NOT EXPOSE THE HARNESS TO CHEMICALS WHICH ARE HARMFUL TO
NYLON. IF IN DOUBT, CONTACT THE MANUFACTURER.
• AVOID CONTACT WITH SHARP EDGES OR ABRASIVE SURFACES.
• USE EXTREME CAUTION WHEN USING THE HARNESS AROUND MOVING
MACHINERY OR ELECTRICAL HAZARDS.
Rescue Harness
ProSeries®Rescue
Harness
CMC Rescue, Inc.
6740 Cortona Drive, Goleta CA 93117
USA
805-562-9120 / 800-235-5741
cmcpro.com
ISO 9001 Certified
©2018 CMC Control No. 20X1XX.012418

The service life of equipment depends greatly on the type of use
and the environment of use. Because these factors vary greatly, a
precise service life of the equipment cannot be provided.
PUTTING ON YOUR HARNESS
1. Loosen the waist and leg adjusting buckles to make the
diameter large enough to pull over your thighs and hips. Hold
the harness by the waist and step through the waist belt and
pull the belt up around your waist.
2. Adjust the waist strap and leg loops for the most comfortable
fit.
3. Fold the web tails under the Web-Keepers™ and secure them
tightly.
WARNING: Make sure the straps are snug. This increases
the comfort when sitting in the harness and helps prevent the
quick-connect buckles from disconnecting. When wearing the
harness, double-check the buckles, adjusters, and fit of the
harness immediately prior to relying on it for support.
ATTACHMENT POINTS
• The front waist D-ring is the primary work positioning attachment
point. It allows the user to be in a sitting position which provides
the most comfort and freedom of movement. The front waist
D-ring on the ProSeries Rescue Harness also serves as an
attachment point to the front of the ProSeries Chest Harness.
• The rear D-ring is intended to provide travel restraint when
working near an edge. The rear D-ring on the ProSeries Rescue
Harness also serves as an attachment point to the rear of the
ProSeries Chest Harness.
WARNING: To prevent roll out, use only locking carabiners
to attach to D-rings.
USING YOUR HARNESS
CMC harnesses are not intended for rock climbing. Lead
climbing ropes should not be tied into the D-ring or connected into
it with a carabiner.
Do not expose the harness to flame or high temperatures. Carry
the harness where it will be protected as the harness could melt or
burn and fail if exposed to flame or high temperatures.
The CMC Rescue and ProSeries Rescue Harnesses are
designed for rescue applications in which the wearer uses the
harness primarily for positioning. High impact fall situations should
be avoided. Always keep the safety line (belay) above the wearer
and keep the slack in the safety line to a minimum.
Equipment Inspection and Maintenance Log
Item __________ # __________ Date in Service _____________
Brand/Model ________________ Size ______________________
Date How Used or Maintained Comments Name
CARRYING, MAINTENANCE & STORAGE
During use, carrying and storage keep the equipment away from
acids, alkalis, exhaust emissions, rust and strong chemicals. Do
not expose the equipment to flame or high temperatures. Carry the
equipment where it will be protected as the equipment could melt
or burn and fail if exposed to flame or high temperatures.
If the equipment becomes soiled, it can be washed in cold water
with a mild detergent that is safe for use with nylon and polyester.
Dry out of direct sunlight. Do not dry in an automatic dryer. Store
in a cool, dry location. Do not store where the equipment may be
exposed to moist air, particularly where dissimilar metals are
stored together. REPAIR
All repair work shall be performed by the manufacturer. All other
work or modifications void the warranty and releases CMC from all
liability and responsibility as the manufacturer.
SAMPLE INSPECTION AND MAINTENANCE LOG
The sample log suggests records that should be maintained by
the purchaser or user of life safety equipment.