Coalesse Lagunitas Arm, Corner & Straight Back... Use and care manual

Page 1 of 7
902507402 Rev A
Lagunitas™Arm, Corner & Straight Back Cushion Replacement
If you have a problem, question, or request, call
your local dealer, or Coalesse at 1.800.627.6770
Or visit our website: www.coalesse.com
©2014 Coalesse
San Francisco, California U.S.A.
Printed in U.S.A.
STRAIGHT
BACK CUSHIONS
ARM CUSHIONS
CORNER
BACK CUSHIONS

Page 2 of 7
902507402 Rev A
Remove Corner Back Cushions and Arm Cushions
1. Remove the seat cushion by lifting up (they are attached
with velcro).
2. Remove the socket head bolt and washer
that attaches the back mounting bracket to the
seat frame.
3. With the bolts removed, slide the mounting brackets
forward about a 1/2 inch to disengage the mounting tabs
in the rear rail. (This may require a hit from a plastic
hammer, to the back of the bracket, to jar it loose)
1
Removal of
Corner Back
Cushions
Removal of
Arm Cushions
1
SEAT CUSHION SEAT CUSHION
SOCKET
HEAD BOLT
WASHER
2
3

Page 3 of 7
902507402 Rev A
Remove Corner Back Cushions and Arm Cushions
(cont.)
4. Remove the arm &/or corner back cushion by lifting up.
Removal of
Arm Cushions
4
ARM CUSHION
Removal of
Corner Back
Cushions
CORNER BACK CUSHION
4

Page 4 of 7
902507402 Rev A
Remove Corner Back Cushions and
Arm Cushions (cont.)
5. Remove the mounting brackets by removing the
socket head bolts from the back of the cushion.
6. Reinstall a new cushion by reversing step 5 and
tightening the bolts to 100 in-lbs.
7. Place the cushion assembly onto the seat frame (reversing
step 4) and insert the mounting tabs into the rectangular holes in
the rear frame rails (reversing step 3 on page 2).
8. Ensure the tabs are inserted all the way into the rectangular
slots in the tube and then install the socket head bolts and
washers through the front mounting tabs and into the seat frame
(reversing step 2 on page 2). Tighten to 130 in-lbs.
9. Reinstall the seat cushion (reversing step 1 on page 2).
TIP: Use cardboard to help place the seat cushion into position. Arm Cushions
5
Corner Back
Cushions
SOCKET HEAD BOLT
MOUNTING
BRACKET
SOCKET HEAD BOLT
MOUNTING
BRACKET
5

Page 5 of 7
902507402 Rev A
Articulating Back Replacement
1. Remove the seat cushion by lifting up (seat cushion is attached
with velcro).
2. Remove the socket head bolt and washer that attaches the back
mounting bracket to the seat frame.
3. With the bolts removed, slide the mounting brackets forward
about a 1/2 inch to disengage the mounting tabs in the rear rail.
(This may require a hit from a plastic hammer, to the back of the
bracket, to jar it loose)
SOCKET
HEAD BOLT
WASHER
2
3
1

Page 6 of 7
902507402 Rev A
Articulating Back Replacement
(cont.)
4. Remove the straight back cushions by lifting up.
4
STRAIGHT BACK CUSHION

Page 7 of 7
902507402 Rev A
Articulating Back Replacement
(cont.)
5. Rotate the mounting bracket assembly 180 degrees so you gain
access to the socket head bolts.
6. Remove the mounting bracket assembly by removing the socket
head bolts from the back of the cushion.
7. Reinstall a new cushion by reversing step 6 and tightening the bolts
to 100 in-lbs.
8. Rotate the mounting bracket assembly 180 degrees before
reassembling to seat frame.
9. Place the straight back cushion assembly onto the seat frame
(reversing step 4 on page 6) and insert the mounting tabs into the
rectangular holes in the rear frame rails (reversing step 3 on page 5).
10. Ensure the tabs are inserted all the way into the rectangular slots in
the tube then install the socket head bolts and washers through the front
mounting tabs and into the seat frame (reversing step 2 on page 5).
Tighten to 130 in-lbs.
11. Reinstall the seat cushion (reversing step 1 on page 5).
5
6
SOCKET HEAD BOLT
MOUNTING BRACKET ASSEMBLY