Crux Sightline RVCAD-81 User manual

RVCAD-81
Rear-view Camera Integration with AV Inputs for
Select Audi Vehicles with MMI-2G
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
rev.031220
1 of 6
- Provides reverse camera input.
- Adds 2 Audio/Video inputs.
- Provides 2 video and 1 set of audio outputs.
- Plug and play installaon.
RVCAD-81
Module
Remote Control Power Harness
IR Extension Cable LCD Cable A/V Cable
Push Buon Switch

rev.031220
2 of 6
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCAD-81
Rear-view Camera Integration with AV Inputs for
Select Audi Vehicles with MMI-2G
TO MMI
MODULE
MMI CABLE
(provided in the kit)
OEM
SCREEN
AV 1
AV 2
AV OUT
V OUT
R CAMERA
+12V ACC GROUND
SAFE (Not used)
REAR-C (Gray wire - Connect to reverse light +12V if CAN is not used)
MMI (Not used)
FACTORY MMI CABLE
DIP# FUNCTION DESCRIPTION
1No Funcon = Set to OFF
2AV 1 ON = Skip
OFF = Display
3AV2 ON = Skip
OFF = Display
4No Funcon - Set to OFF
5No Funcon - Set to OFF
6No Funcon - Set to OFF
7Backup Camera Source ON = Aermarket Backup Camera
OFF = OEM Backup Camera
8No funcon = Set to ON
REAR CAMERA POWER
The rear camera power needs to be tapped to the vehicle’s reverse light. If for some reason the
screen does not changeover to rear camera view aer pung the gear in reverse, tap the GRAY
wire (labeled REAR-C) to the reverse light +12V.

rev.031220
3 of 6
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCAD-81
Rear-view Camera Integration with AV Inputs for
Select Audi Vehicles with MMI-2G
1. Remove the screws below the glove box. 2. Open the glove box and remove the screws that
hold the CD changer facia plate.
3. Remove the fuse box cover (at the right side of the
dashboard) and reemove the two screws.
4. Pull out the glove box and set aside.
5. Remove the CD changer. 6. Unplug the RED power connector from the MMI.
The installaon of the RVCAD-81 is done at the MMI Module. The MMI Module is located above the glove box
or by the passenger side transmission hump.

rev.031220
4 of 6
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCAD-81
Rear-view Camera Integration with AV Inputs for
Select Audi Vehicles with MMI-2G
7. Remove the metal plate to unplug the LCD
connector.
8. Unplug the LCD connector.
9. Plug the LCD cable from the OEM monitor to the
RVCAD-81 LCD OUT connector.
10. Plug the LCD cable pigtail (included in the kit) to
the MMI Module.
REMOTE CONTROL:
BUTTON FUNCTION
Power No Funcon
PIP No Funcon
MENU Enter OSD Menu
OK Select / Enter
Move Up
Move Down
Move Le, Press for 2 seconds to enter Factory Mode
Move Right
Special Note: To enter OSD menu please make sure Dip Switch
2 is in the ON position so that AV1 will be available. Next, enter
AV1 input setting by using the push button to change inputs. Use
the remote to select desired settings. Once desired settings is
chosen, remove power to the module and change Dip switch 2
to the o position. Make sure the module is connected to power
again and start the vehicle.

rev.031220
5 of 6
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCAD-81
Rear-view Camera Integration with AV Inputs for
Select Audi Vehicles with MMI-2G
OSD SETTINGS:
To enter the OSD Menu: Press the MENU buon on the remote control
IMAGE
- BRIGHTNESS
- CONTRAST
- SATURATION
- HUE
- SHARPNESS
- USER IMAGE: Choose
from 4 color shardes
OSD
- LANGUAGE: Choose OSD language
- T R A N S : Tr a n s p a re n c y c o n t r o l o f
OSD background
- HI_ POSITION: Horizontal movement
of the OSD window
- V-POSITION: Vercal movement of
the OSD window
UTIL
- USER RESET: RESET OSD
Enter Factory Mode by pressing the buon on the remote control for 2 seconds
IMAGE
- H-POSITION: Control over horizontal movement of the screen
- V-POSITION: Control over vercal movement of the screen
PARK
- PARK ENABLE: Set parking guide lines
- PARK SETUP: Control over posion of parking guide lines

rev.031220
6 of 6
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCAD-81
Rear-view Camera Integration with AV Inputs for
Select Audi Vehicles with MMI-2G
MMI 2G MMI 2G
Turn Parking Lines ON or OFF using the PARK ENABLE opon.
It is factory defaulted to ON.
Test by pung the gear in reverse. The parking lines should
show on the screen. Press OK on the remote control to the
horizontal posion (H-POS) of the parking lines.
Aer adjusng the horizontal poson, press OK again to
adjust the Vercal Posion (V-POS) of the parking lines.
Enter Factory Mode by pressing the buon on the remote control for 2 seconds
AUDI
2008 - 2009 A4
2004 - 2011 A6
2006 - 2011 S6
2008 - 2010 RS6
2003 - 2008 A8
2006 - 2008 S8
2005 - 2009 Q7