Dynojet POWER VISION 4 User manual

POWER VISION 4
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
98200143.01
Installation Guide for: PV4-15-02
Model Coverage: 2011-2020 Harley-Davidson

2 POWER VISION 4 INSTALLATION AND USER GUIDE
INTRODUCTION
Thank you for purchasing the Power Vision 4 (PV4) from
Dynojet Research. The Power Vision 4 is the most flexible
and powerful flash tuner in the world. The Power Vision 4
uses reflash technology to change the parameters inside
the stock Engine Control Module (ECM) that affects the way
the engine will run.
The Power Vision 4 has three indicator lights:
• Red LED—Communication. Solid red is communication on
bus; rapid flashing is recovery mode.
• Green LED—Power. Short blink is power; long blink is
connected to ECU.
• Blue LED—Bluetooth status. On is connected to Bluetooth;
off is not connected.
After the vehicle has been flashed, the Power Vision 4 does
not need to remain connected to have full benefits of the
device.
For state of the art technical support, please visit
www.dynojet.zendesk.com.
LOCATING THE DIAGNOSTIC CONNECTOR
2012-2017 Dyna Models
The diagnostic connector is located under
the left hand side electrical cover. This
connector is light grey in color with a black
rubber plug installed.
2014-2021 Sportster Models
Including XR Models
The diagnostic connector is located under
the left hand side electrical cover. This
connector is light grey in color with a black
rubber plug installed.
2011-2020 Softail Models
The diagnostic connector is located under
the seat attached to the frame by the rear
fender. This connector is light grey in color
with a black rubber plug installed.

3
LOCATING THE DIAGNOSTIC CONNECTOR
2015-2021 Street 500 and 750 Models
The diagnostic connector is located under
the right hand side electrical cover. This
connector is light grey in color with a
black rubber plug installed.
2002-2007 Touring Models
The diagnostic connector is located under
the right hand side electrical cover. This
connector is light grey in color with a black
rubber plug installed. Requires removing
the right saddle bag.
2008-2020 Touring Models
The diagnostic connector is located under
the left hand side electrical cover. This
connector is light grey in color with a black
rubber plug installed. Requires removing
the left saddle bag.
2021-2022 Touring Models
The diagnostic connector is located
behind the left hand side cover. This
connector is red, 6-pin. Requires removing
the left saddle bag.
2002-2017 V-Rod Models
The diagnostic connector is located under
the right front frame cover. This connector
is light grey in color with a black rubber
plug installed. Requires tools to access.
2021-2022 Sportster S
The diagnostic connector is located
underneath the seat.
This connector is red, 6-pin.
2021-2022 Pan America
The diagnostic connector is located
underneath the main seat.
This connector is red, 6-pin.

4 POWER VISION 4 INSTALLATION AND USER GUIDE
GETTING STARTED
1 Download and install the Dynojet Power Vision app from
the Apple App or Google Play Store.
2 Verify Bluetooth and Location are enabled.
Location permission is required for the app to access
the phone’s Bluetooth hardware.
3 Connect the Power Vision to the vehicle diagnostic port.
4 Turn the ignition switch to the ON position and the run
switch to the RUN position, but do not start the vehicle.
5 Open the Dynojet Power Vision app.
6 Log in using your Dynojet account login information.
Don’t have a Dynojet account? Press I don’t have an
account and create one. Enter your information and a
password and press Register.
7 Press Scan.
8 Select the Dynojet PV4.
Don’t have
an account?
Create one!
9 Press the Pencil to edit the vehicle name. Press Update
to save.
10 Press Tunes.
Note: The first time you connect to a vehicle you will
need to Read the ECU. Press Yes to continue.
11 Type in a stock file name. The VIN is used by default.
This file will be uploaded to your Cloud account.
Select the PV4
First time
connections
will need to
read the ECU
Name the
stock file
Log in Enter your
information
to create an
account
Indicates the
vehicle you are
connected to
Edit pencil
Scan for PV4

5
FLASHING YOUR VEHICLE
Your Power Vision 4 comes with one available Tune
License. Before you can flash additional vehicles, you
will need to purchase additional tune licenses from
Dynojet.
1 Press Tunes.
2 Select a tune file (.djt) from the list of available Dynojet
Tunes or press Filter to filter the list of tunes.
3 Tap a Filter field and select from the available options to
narrow the results.
4 Once you have selected your filters, slide the filter
screen to the left. Select a tune file from the filtered list.
5 Press Flash Tune.
6 Press Yes to use the included Tune License to lock the
Power Vision 4 to this vehicle and flash the tune. Do not
turn off the key switch or disconnect the Power Vision
during the flash.
Select the filter
option
Press the
field to view
available
options
Choose from
available
Dynojet tunes
Tunes
Use the
included Tune
License to lock
to the vehicle
and begin flash
Flash Tune
Filter
Filter