emaux UNDERWATER LIGHT Series User manual

UNDERWATER LIGHT SERIES
UL-P100 LED-P100 UL-TP100 LED-TP100
UL-CP100 LED-CP100 UL-NS75/150
Installation and Operation manual
USER MANUAL
STRIVE FOR CLEAR WATER
EMAUX WATER TECHNOLOGY CO., LTD
www.emauxgroup.com
SAA
EMPU21080641
IP68

Underwater Light Series
TABLE OF
CONTENT
PAGE
2
....
2
7
....
....
3
....
P1 CONTENT
1. IMPORTANT SAFETY AND INSTALLATION INSTRUCTIONS
2. PRODUCT INTRODUCTION
2.1 TRANSFORMER+LIGHTS
2.2 CONTROL BOX+TRANSFORMER+LIGHTS
3. LIGHT SPECIFICATION
3.1 ELECTRICAL
3.2 COLOR MODE
4. INSTALLATION NOTES
5. LAMP INSTALLATION
5.1 Preparing to Install
5.2 UL-P100 LED-P100 UL-CP100 LED-CP100 UL-NS75/150 INSTALLATION
6. MAINTENANCE OF THE LIGHTS
7. SPARE PART LIST
4
....
5
....
6
....
P100/TP100/CP100/NS SERIES
8. TERMS OF THE WARRANTY
As original purchaser of this equipment have purchased from Emaux Water Technology Co Ltd, through
Authorized International Distributor or Dealer, warrants its products free from defects in materials and
workmanship under normal use during warranty period. The warranty period begins on the day of purchase and
extends only to the original purchaser. It is not transferable to anyone who subsequently purchases the product
from you. It excludes all expendable parts.
During the warranty period, Emaux authorized reseller will repair or replace defective parts with new parts or, at
the option of Emaux, serviceable used parts that are equivalent or superior to new parts in performance.
This Limited Warranty extends only to products purchased from Emaux authorized reseller. This Limited
Warranty does not extend to any product that has been damaged or rendered defective
1. as a result of accident, misuse or abuse;
2. as a result of an act of God;
3. by operation outside the usage parameters stated herein;
4. by the use of parts not manufactured or sold by Emaux;
5. by modification of the product;
6. as a result of war or terrorist attack; or
7. as a result of service by anyone other than Emaux authorized reseller or authorized agent.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, EMAUX MAKES NO OTHER WARRANTIES EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. EMAUX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY
IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS EXPRESS LIMITED
WARRANTY.
TERMS OF THE WARRANTY P14
14
.... 8. TERMS OF THE WARRANTY

IMPORTANT SAFETY AND INSTALLATION INSTRUCTIONS P2
1. IMPORTANT SAFETY AND INSTALLATION INSTRUCTIONS
Please read the manual carefully before commencing installation. This manual contains important
information about the correct installation and operation of lights.
1. Only qualified electrician is allowed to carry out the installation of this product.
2. Avoid direct contact with electrical power.
3. Respect all regulations in effect for preventing accidents.
4. All units are required to be disconnected from the main electricity before any operation of maintenance.
5. For safe and proper installation, ensure that those parts supplied with the produce are used.
6. Never handle with wet hands and feet.
7. This unit is design for use only when fully submerged in fresh water, connecting with a safety transformer
8. This product should be installed according to your local electrical installation ordinances and regulations.
9. Due to the corrosive nature of unbalanced pool chemicals, please keep you pool water is acid-base balanced
prior to installation, and ensure the longevity of these lights.
10. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the
manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
11. Check that there is enough cable behind light to allow for servicing above water, preferably at ground-level
pool-side.
12. Never operate this Underwater Light for more than 1 minute unless it is totally submerged in water.
13. You lights require cleaning at any time, be sure to a mild detergent or other ways that don't damage to the
lights.
14. Be sure power is off before installing or removing light. Allow light to cool before replacing.
15. Maximum Depth for Light installation at 1.2 meter.
16. Maximum Water Temperature Range for light operation 0-25°C
For non replacable lightsources: ”The light source of this luminaire is not replaceable; when the light source
reaches its end of life the whole luminaire shall be replaced”.
For operation only with safety isolating transformer conforming with AS/NZS 61558 series.
2. PRODUCT INTRODUCTION
2.1 TRANSFORMER+LIGHTS
When the light is connected to the transformer directly, to on /off the main switch to controls the color changes.
For LED-P100/TP100/CP100 RGB, When it’s different colors, turn off the lights, wait 3-5S and turn on the lights,
it’s the same colors.
1
UL-NS75/150
Key No.
Part No.
Description
Qty
1
01051169
Face Ring for UL-NS75
1
1
01051170
Face Ring for UL-NS150
1
2
01041037
Lens for UL-NS75
1
2
01040208
Lens for UL-NS150
1
3
02021027
Waterproof Washer for UL-NS75
1
3
02021062
Waterproof Washer for UL-NS150
1
4*
E041204
Bulb 12V/ 75W for ULH/ UL-NS
*
5
89043704
Stainless Steel Lights Face Plate for UL-NS75
1
5
89043703
Stainless Steel Lights Face Plate for UL-NS150
1
6
03011016
M5*15 Screw on Face Plate
1
7
03011127
M5*8 Screw for UL-NS75 &- NS150
*
8
02021036
O-Ring for Face Plate (UL-NS75)
1
8
02021028
O-Ring for Face Plate (UL-NS150)
1
9
03011149
M6*40 Mounting screw
4
10
01051171
Mounting Bracket for UL-NS75
1
10
01051172
Mounting Bracket for UL-NS150
1
11
02011158
Gasket
2
12
89043702
Wall Bracket
1
P13 SPARE PART LIST
2
3
4
5
6
7
8
9
10
11
12

P3 LIGHT SPECIFICATION
2.2 CONTROL BOX+TRANSFORMER+LIGHTS
It need to cooperate with RGB Control Box to change color. Put the “RESET” buton when it’s different colors.
ON/OFF Switch ON/OFF Switch ON/OFF Switch
Light
Transformer Transformer Transformer
Light
Master Switch
Light
SPA
INPUT:
C 220~240V
(AC110V)
Control box
220~240V(110V)
220~240V(110V)
LED Light
Tranformer
12V
POOL
3. LIGHT SPECIFICATION
3.1 ELECTRICAL
(1) Operation Voltage Range: AC12V (COS : 0.8 )
(2) Light Color: LED: RGB, Warm White, Cool White
Halogen Lamp: Warm White
(3) Operation Frequency: 50/60Hz
(4) Max Power Rating: 75W(UL-P100/TP100/CP100,UL-NS75), 150W(UL-NS150) , 6W/8W(LED-P100/TP100/CP100)
(5) Installation Types: Concrete Pool/Vinyl Pool
3.2 COLOR MODE
Colour change options(For RGB version only)
Attention: When turn off the lights
Wait less than 2s and turn on, change color
wait 3-5S and turn on, reset the first mode(Automatic )
wait over 10S and turn on, Memory the mode before turning off
SPARE PART LIST P12
LED-CP100
Concrete Pool
Vinyl Pool
Key No.
Part No.
Description
Qty
1
03011321
M5X20 screws (316#)
1
2
01040212
Lights Lens
1
3
01012031
Face plate
1
4
01110027
Compression screw
1
5
02010237
O-ring
1
6
89045601
Bulb plate(White Colour),12V/8W 198LEDs
1
6
89045602
Bulb Plate(RGB) 12V/6W 102LEDs
1
6
89045603
Bulb Plate(RGB) 12V/8W 198LEDs
1
6
89045604
Bulb Plate(White Colour), 12V/6W 102LEDs
1
7
89044501
Lights Vinyl Pool Fitting for P100/ CP100
1
8
89040203
Lights Concrete Pool Fitting for P100/ CP100
1
8
7
6
5
4
3
2
1

INSTALLATION NOTES P4
4. INSTALLATION NOTES
1. It is recommended to install a light every 20 , the approximate exposure area of each unit.
2. The lights should be installed in the direction that they will not shine directly into the house.
3. For training or competition pools, the lights must be installed on the sides in order to prevent swimmers from
seeing any glare.
4. Nothing should be placed on the pool side directly above the lights for ease of future maintenance.
5. The cables connecting the lights and the transformers must be at least 6mm² and the distance between them
must not exceed 30m; otherwise the lights will not function properly.
6. Terminal blocks must meet the IEC60988-2-1 standard having the rated connecting capacity of 4,0mm² use of
screw-type terminal at least 25A current rating, mounted on junction boxes inside.
m²
Mode E: RGB Colour Sequence: Red>Green>Blue
Mode F: Four Colour Sequence: Red>Green>Blue>Purple
Auto Colour Change
White
Green
Green+Blue
Red+Blue
Mode B: Green+Gradual Red
Blue
Red+Green
Mode C: Blue+Gradual Green
Mode A: Blue+ Gradual Red
Mode D: Blue+Gradual Red
Rapid Auto Colour Change
Automatic
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
=30m
Transformer
Light
P11 SPARE PART LIST
UL-CP100
Key No.
Part No.
Description
Qty
1
03011321
M5*20 Screw (316#)
1
2
01050102
Face plate
1
3
01110027
Compression screw
1
4
01040212
Lights Lens
1
5
E041204
Bulb 12V/75W for ULH/ UL-NS
1
6
03011132
M4*8 Screw
3
7
03011150
Screw
2
8
04011031
Lamp Socket
1
9
03013039
But
2
10
03017118
Reflector Plate
1
11
04014016
Closed-End Wire Connector
2
12
02021084
O-Ring for UL-CP100
1
13
01231008
UL-CP100 Light Body Set(with 2.5M cable and socket)
1
14
89044501
Vinyl pool Fitting for P100
1
15
89040203
Fitting for Concrete Pool
1
14 15
1
2
3
4
5
6
7
8
9
10
11
12
13
****
In case of replacement of an old LED-CP100 / TP100 / P100 Auto-Color light by a new LED-CP100
RGB model (15 preset programs), please note:
1) All the lights can be synchronized in "Automatic color change" mode that is pre-installed on the new LED-
CP100 / TP100 / P100 RGB lights as a Program 1.
Synchronization instructions: Turn off / turn on the light every 2 seconds to select a Program 1 on the LED-
CP100 / TP100 / P100 RGB. it stays on. It takes 10 seconds to get fixed the Program (color). From then on, all
the lights will be synchronized, and the color will be changed automatically.
2) To use all 15 preset programs, all the old LED-CP100 / TP100 / P100 Auto-Color lights must be replaced with
new LED-CP100 / TP100 / P100 RGB version.
****
/ TP100 / P100

P5 LAMP INSTALLATION
1) The circuit system must comply with local laws and regulations and must be carried out by suitably qualified
installers.
2) Make sure the voltage is 12V and the terminal box is at least 120cm from the poolside .
3) Upon installation, top of the light must be at least 45cm from water surface.
5.2 UL-P100 LED-P100 UL-CP100 LED-CP100 UL-NS75/150 INSTALLATION
A) Concrete Pools Installation
1 Embed the Wall Mount into the concrete wall, making sure that it is parallel to the side of the pool.(Figure 4).
2) Place the Mounting Plate on the concrete wall and tighten it with 4 screws. The Conduit must be next to the
Mounting Plate (Figure 5).
3) Note that the light must only be installed on a flat or concave surface.
4) Wrap extra cables behind the light to make sure it could be taken to the pool surface for future maintenance
(Figure 6).
5) Hang the light onto the Mounting Plate and tighten the screws (Figure 7).
6) The wire connections inside the terminal box must be sealed by leak-proof tapes to prevent water from leaking
into the terminal box through the cables.
)
DO NOT MOUNT ON:
Reverse radius
surface Irregular or uneven surfaces
DO MOUNT ON:
Flat surface Walls with no tighter
Radius as Viewed from top
Than 6 ft.
Figure 6 Figure 7Figure 4 Figure 5
NS75/150
P100/CP100
TP100
SPARE PART LIST P10
LED-TP100
Key No.
Part No.
Description
Qty
1
01050119
Lights Face plate
1
2
03011364
M4*12 Screw
1
3
04011109
Bulb plate 12V/8W 198LEDs For White Colour
1
3
04011110
Bulb plate 12V/8W 198LEDs For Colour-changing
1
3
440546887
Bulb plate 12V/8W 198LEDs For Warm White Colour
1
3
04011113
Bulb plate 12V/8W 198LEDs For Blue Colour
1
4
03011364
M4*12 Screw
2
5
01012005
UL/LED-TP100 Lights Bracket
1
6
03011363
M4*16 Screw
2
7
89040401
UL/LED-TP100 Lights Vinyl pool Fitting
1
8
89040501
LED-TP100 Lights Concrete Pool Fitting
1
3
1
2
4
6
5
Vinyl Pool
7Concrete Pool
8
5.1 Preparing to Install
Concrete must be cut backaround niche
to allow fora compact plaster seal
120cm min.
Water level
Rigid conduit
Junction box
45cm min. from water
line to top of lens
6.6cm
29.6cm
5. LAMP INSTALLATION

MAINTENANCE OF THE LIGHTS P6
Figure 12 Figure 13 Figure 14 Figure 15
6. MAINTENANCE OF THE LIGHTS
1. Do not leave the lights “on” above water for longer than 1 minute.
2. Before switching on the lights, check whether the lights are fully submerged underwater and the circuit boxes
are running properly.
3. This unit does not need any kind of maintenance. If it is not working properly, please contact EMAUX
authorized dealer where you purchase the unit from.
4. Warranty will be voided if the Emaux Underwater Light was dismantled by unauthorized personnel.
Mounting plate
O-ring Nut
Figure 9 Figure 10Figure 8
2X24
147,5
2X24
110
P100/CP100
TP100
TP100
NS75/150
Figure 11
C)
1) Clean the O-ring installation position and put the O-ring. (Figure 12)
2) After install the O-ring. Put the transparency lid and then put the cover. (Figure 13)
3) While install the cover with the base, please to note that the sign of “TOP”from the base should meet with the
sign of “TOP“ for the cover. (Figure 14)
4) Rotate to the station position and then to use screw driver that to tighten. (Figure 15)
5) For Unassembled, please to reverse the sequence.
Assembly for CP100
UL-TP100
Key No.
Part No.
Description
Qty
1*
01221003
Colour lens (Red+Green+Blue) for P100, DP100
1
2
01051259
Face Plate for TP100
1
3
03011307
M4*12 Screw
1
4
01040211
Lights Lens
1
5
02021055
O-Ring for TP100
1
6
E040205
Halogen high Bulb (Yellow Light)
1
7
89040402
UL-TP100 Lights Body Set(with 2.5M cable and socket)
1
8
03011331
M4*12 Screw
8
9
03011332
M4*16 Screw
2
10
01012005
TP100 Lights Bracket
1
11
89040401
TP100 Lights Vinyl Pool Fitting
1
12
89040501
TP100 Lights Concrete Pool Fitting
1
Note:*UL-TP100 Light Colour Lens 1 set (Red+Green+Blue)
9
4
1
2
3
5
6
8
7
10
P9 SPARE PART LIST
Vinyl Pool
11 Concrete Pool
12
B) Fiberglass Pools / Vinyl Pools Installation
1 Refer to section"Preparing to Install".
2) Make 2 holes on the pool wall (Figure 8).
3) Place the o-rings between the Mounting Plate and the pool wall and tighten it with the Nut on the other side of
the pool wall (Figure 9).
4) Put the cable sequentially through the sealing Nut, the sealing O-ring and the cable hole on the mounting plate;
then tighten the Nut (Figure10).
5) Wrap extra cables behind the light to make sure it could be taken to the pool surface for future maintenance.
Then, hang the light onto the Mounting Plate and tighten the screws (Figure 11).
)

7. SPARE PART LIST
UL-P100
Key No.
Part No.
Description
Qty
1*
01221002
Colour lens (Red+Green+Blue) for P100
1
2
03011321
M5*20 Screw (316#)
1
3
01051059
Face Ring
1
4
01041021
P100 Lights Lens
1
5
03021018
M6 Brass Nut
8
6
01051058
P100 Lights Face plate
1
7
02021004
O-ring
1
8
E040205
Halogen light bulb (Yellow Light)
1
9
89040201
P100 Lights Body set(with 2.5M cable and socket)
1
10
03011320
M6*20 Screw (316#)
8
11
89040203
Concrete Pool Fittingfor P100
1
12
89044501
Vinyl Pool Fitting for P100
1
Notes: 1* 01221001 is UL-P100 Light Colour Lens 1 set with (Red+Green+Blue)
1
2
3
4
5
6
7
8
9
10
P7 SPARE PART LIST
Vinyl Pool
11 Concrete Pool 12
LED-P100
Key No.
Part No.
Description
Qty
1
03011321
M5*20 Screw (316#)
1
2
01051059
Face Ring
1
3
03021018
M6 Brass Nut
4
4
01051058
P100 Lights Face plate
1
5
04011111
Bulb plate 12V/8W LED (Cool White Color)
1
04011115
Bulb plate 12V/8W LED (Blue Color)
04011112
Bulb plate 12V/8W LED (Auto Color changing)
4405470016
Bulb plate 12V/16W LED (Cool White Color)
4405470017
Bulb plate 12V/16W LED (Auto Color changing)
6
03011320
M6*20 Screw(316#)
4
7
89040203
Concrete pool Fitting for P100
1
8
89044501
Vinyl pool Fitting for P100
1
1
2
3
4
5
6
SPARE PART LIST P8
Vinyl Pool
7Concrete Pool 8

MAINTENANCE OF THE LIGHTS P6
Figure 12 Figure 13 Figure 14 Figure 15
6. MAINTENANCE OF THE LIGHTS
1. Do not leave the lights “on” above water for longer than 1 minute.
2. Before switching on the lights, check whether the lights are fully submerged underwater and the circuit boxes
are running properly.
3. This unit does not need any kind of maintenance. If it is not working properly, please contact EMAUX
authorized dealer where you purchase the unit from.
4. Warranty will be voided if the Emaux Underwater Light was dismantled by unauthorized personnel.
Mounting plate
O-ring Nut
Figure 9 Figure 10Figure 8
2X24
147,5
2X24
110
P100/CP100
TP100
TP100
NS75/150
Figure 11
C)
1) Clean the O-ring installation position and put the O-ring. (Figure 12)
2) After install the O-ring. Put the transparency lid and then put the cover. (Figure 13)
3) While install the cover with the base, please to note that the sign of “TOP”from the base should meet with the
sign of “TOP“ for the cover. (Figure 14)
4) Rotate to the station position and then to use screw driver that to tighten. (Figure 15)
5) For Unassembled, please to reverse the sequence.
Assembly for CP100
UL-TP100
Key No.
Part No.
Description
Qty
1*
01221003
Colour lens (Red+Green+Blue) for P100, DP100
1
2
01051259
Face Plate for TP100
1
3
03011307
M4*12 Screw
1
4
01040211
Lights Lens
1
5
02021055
O-Ring for TP100
1
6
E040205
Halogen high Bulb (Yellow Light)
1
7
89040402
UL-TP100 Lights Body Set(with 2.5M cable and socket)
1
8
03011331
M4*12 Screw
8
9
03011332
M4*16 Screw
2
10
01012005
TP100 Lights Bracket
1
11
89040401
TP100 Lights Vinyl Pool Fitting
1
12
89040501
TP100 Lights Concrete Pool Fitting
1
Note:*UL-TP100 Light Colour Lens 1 set (Red+Green+Blue)
9
4
1
2
3
5
6
8
7
10
P9 SPARE PART LIST
Vinyl Pool
11 Concrete Pool
12
B) Fiberglass Pools / Vinyl Pools Installation
1 Refer to section"Preparing to Install".
2) Make 2 holes on the pool wall (Figure 8).
3) Place the o-rings between the Mounting Plate and the pool wall and tighten it with the Nut on the other side of
the pool wall (Figure 9).
4) Put the cable sequentially through the sealing Nut, the sealing O-ring and the cable hole on the mounting plate;
then tighten the Nut (Figure10).
5) Wrap extra cables behind the light to make sure it could be taken to the pool surface for future maintenance.
Then, hang the light onto the Mounting Plate and tighten the screws (Figure 11).
)

P5 LAMP INSTALLATION
1) The circuit system must comply with local laws and regulations and must be carried out by suitably qualified
installers.
2) Make sure the voltage is 12V and the terminal box is at least 120cm from the poolside .
3) Upon installation, top of the light must be at least 45cm from water surface.
5.2 UL-P100 LED-P100 UL-CP100 LED-CP100 UL-NS75/150 INSTALLATION
A) Concrete Pools Installation
1 Embed the Wall Mount into the concrete wall, making sure that it is parallel to the side of the pool.(Figure 4).
2) Place the Mounting Plate on the concrete wall and tighten it with 4 screws. The Conduit must be next to the
Mounting Plate (Figure 5).
3) Note that the light must only be installed on a flat or concave surface.
4) Wrap extra cables behind the light to make sure it could be taken to the pool surface for future maintenance
(Figure 6).
5) Hang the light onto the Mounting Plate and tighten the screws (Figure 7).
6) The wire connections inside the terminal box must be sealed by leak-proof tapes to prevent water from leaking
into the terminal box through the cables.
)
DO NOT MOUNT ON:
Reverse radius
surface Irregular or uneven surfaces
DO MOUNT ON:
Flat surface Walls with no tighter
Radius as Viewed from top
Than 6 ft.
Figure 6 Figure 7Figure 4 Figure 5
NS75/150
P100/CP100
TP100
SPARE PART LIST P10
LED-TP100
Key No.
Part No.
Description
Qty
1
01050119
Lights Face plate
1
2
03011364
M4*12 Screw
1
3
04011109
Bulb plate 12V/8W 198LEDs For White Colour
1
3
04011110
Bulb plate 12V/8W 198LEDs For Colour-changing
1
3
440546887
Bulb plate 12V/8W 198LEDs For Warm White Colour
1
3
04011113
Bulb plate 12V/8W 198LEDs For Blue Colour
1
4
03011364
M4*12 Screw
2
5
01012005
UL/LED-TP100 Lights Bracket
1
6
03011363
M4*16 Screw
2
7
89040401
UL/LED-TP100 Lights Vinyl pool Fitting
1
8
89040501
LED-TP100 Lights Concrete Pool Fitting
1
3
1
2
4
6
5
Vinyl Pool
7Concrete Pool
8
5.1 Preparing to Install
Concrete must be cut backaround niche
to allow fora compact plaster seal
120cm min.
Water level
Rigid conduit
Junction box
45cm min. from water
line to top of lens
6.6cm
29.6cm
5. LAMP INSTALLATION

INSTALLATION NOTES P4
4. INSTALLATION NOTES
1. It is recommended to install a light every 20 , the approximate exposure area of each unit.
2. The lights should be installed in the direction that they will not shine directly into the house.
3. For training or competition pools, the lights must be installed on the sides in order to prevent swimmers from
seeing any glare.
4. Nothing should be placed on the pool side directly above the lights for ease of future maintenance.
5. The cables connecting the lights and the transformers must be at least 6mm² and the distance between them
must not exceed 30m; otherwise the lights will not function properly.
6. Terminal blocks must meet the IEC60988-2-1 standard having the rated connecting capacity of 4,0mm² use of
screw-type terminal at least 25A current rating, mounted on junction boxes inside.
m²
Mode E: RGB Colour Sequence: Red>Green>Blue
Mode F: Four Colour Sequence: Red>Green>Blue>Purple
Auto Colour Change
White
Green
Green+Blue
Red+Blue
Mode B: Green+Gradual Red
Blue
Red+Green
Mode C: Blue+Gradual Green
Mode A: Blue+ Gradual Red
Mode D: Blue+Gradual Red
Rapid Auto Colour Change
Automatic
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
=30m
Transformer
Light
P11 SPARE PART LIST
UL-CP100
Key No.
Part No.
Description
Qty
1
03011321
M5*20 Screw (316#)
1
2
01050102
Face plate
1
3
01110027
Compression screw
1
4
01040212
Lights Lens
1
5
E041204
Bulb 12V/75W for ULH/ UL-NS
1
6
03011132
M4*8 Screw
3
7
03011150
Screw
2
8
04011031
Lamp Socket
1
9
03013039
But
2
10
03017118
Reflector Plate
1
11
04014016
Closed-End Wire Connector
2
12
02021084
O-Ring for UL-CP100
1
13
01231008
UL-CP100 Light Body Set(with 2.5M cable and socket)
1
14
89044501
Vinyl pool Fitting for P100
1
15
89040203
Fitting for Concrete Pool
1
14 15
1
2
3
4
5
6
7
8
9
10
11
12
13
****
In case of replacement of an old LED-CP100 / TP100 / P100 Auto-Color light by a new LED-CP100
RGB model (15 preset programs), please note:
1) All the lights can be synchronized in "Automatic color change" mode that is pre-installed on the new LED-
CP100 / TP100 / P100 RGB lights as a Program 1.
Synchronization instructions: Turn off / turn on the light every 2 seconds to select a Program 1 on the LED-
CP100 / TP100 / P100 RGB. it stays on. It takes 10 seconds to get fixed the Program (color). From then on, all
the lights will be synchronized, and the color will be changed automatically.
2) To use all 15 preset programs, all the old LED-CP100 / TP100 / P100 Auto-Color lights must be replaced with
new LED-CP100 / TP100 / P100 RGB version.
****
/ TP100 / P100

P3 LIGHT SPECIFICATION
2.2 CONTROL BOX+TRANSFORMER+LIGHTS
It need to cooperate with RGB Control Box to change color. Put the “RESET” buton when it’s different colors.
ON/OFF Switch ON/OFF Switch ON/OFF Switch
Light
Transformer Transformer Transformer
Light
Master Switch
Light
SPA
INPUT:
C 220~240V
(AC110V)
Control box
220~240V(110V)
220~240V(110V)
LED Light
Tranformer
12V
POOL
3. LIGHT SPECIFICATION
3.1 ELECTRICAL
(1) Operation Voltage Range: AC12V (COS : 0.8 )
(2) Light Color: LED: RGB, Warm White, Cool White
Halogen Lamp: Warm White
(3) Operation Frequency: 50/60Hz
(4) Max Power Rating: 75W(UL-P100/TP100/CP100,UL-NS75), 150W(UL-NS150) , 6W/8W(LED-P100/TP100/CP100)
(5) Installation Types: Concrete Pool/Vinyl Pool
3.2 COLOR MODE
Colour change options(For RGB version only)
Attention: When turn off the lights
Wait less than 2s and turn on, change color
wait 3-5S and turn on, reset the first mode(Automatic )
wait over 10S and turn on, Memory the mode before turning off
SPARE PART LIST P12
LED-CP100
Concrete Pool
Vinyl Pool
Key No.
Part No.
Description
Qty
1
03011321
M5X20 screws (316#)
1
2
01040212
Lights Lens
1
3
01012031
Face plate
1
4
01110027
Compression screw
1
5
02010237
O-ring
1
6
89045601
Bulb plate(White Colour),12V/8W 198LEDs
1
6
89045602
Bulb Plate(RGB) 12V/6W 102LEDs
1
6
89045603
Bulb Plate(RGB) 12V/8W 198LEDs
1
6
89045604
Bulb Plate(White Colour), 12V/6W 102LEDs
1
7
89044501
Lights Vinyl Pool Fitting for P100/ CP100
1
8
89040203
Lights Concrete Pool Fitting for P100/ CP100
1
8
7
6
5
4
3
2
1

IMPORTANT SAFETY AND INSTALLATION INSTRUCTIONS P2
1. IMPORTANT SAFETY AND INSTALLATION INSTRUCTIONS
Please read the manual carefully before commencing installation. This manual contains important
information about the correct installation and operation of lights.
1. Only qualified electrician is allowed to carry out the installation of this product.
2. Avoid direct contact with electrical power.
3. Respect all regulations in effect for preventing accidents.
4. All units are required to be disconnected from the main electricity before any operation of maintenance.
5. For safe and proper installation, ensure that those parts supplied with the produce are used.
6. Never handle with wet hands and feet.
7. This unit is design for use only when fully submerged in fresh water, connecting with a safety transformer
8. This product should be installed according to your local electrical installation ordinances and regulations.
9. Due to the corrosive nature of unbalanced pool chemicals, please keep you pool water is acid-base balanced
prior to installation, and ensure the longevity of these lights.
10. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the
manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
11. Check that there is enough cable behind light to allow for servicing above water, preferably at ground-level
pool-side.
12. Never operate this Underwater Light for more than 1 minute unless it is totally submerged in water.
13. You lights require cleaning at any time, be sure to a mild detergent or other ways that don't damage to the
lights.
14. Be sure power is off before installing or removing light. Allow light to cool before replacing.
15. Maximum Depth for Light installation at 1.2 meter.
16. Maximum Water Temperature Range for light operation 0-25°C
For non replacable lightsources: ”The light source of this luminaire is not replaceable; when the light source
reaches its end of life the whole luminaire shall be replaced”.
For operation only with safety isolating transformer conforming with AS/NZS 61558 series.
2. PRODUCT INTRODUCTION
2.1 TRANSFORMER+LIGHTS
When the light is connected to the transformer directly, to on /off the main switch to controls the color changes.
For LED-P100/TP100/CP100 RGB, When it’s different colors, turn off the lights, wait 3-5S and turn on the lights,
it’s the same colors.
1
UL-NS75/150
Key No.
Part No.
Description
Qty
1
01051169
Face Ring for UL-NS75
1
1
01051170
Face Ring for UL-NS150
1
2
01041037
Lens for UL-NS75
1
2
01040208
Lens for UL-NS150
1
3
02021027
Waterproof Washer for UL-NS75
1
3
02021062
Waterproof Washer for UL-NS150
1
4*
E041204
Bulb 12V/ 75W for ULH/ UL-NS
*
5
89043704
Stainless Steel Lights Face Plate for UL-NS75
1
5
89043703
Stainless Steel Lights Face Plate for UL-NS150
1
6
03011016
M5*15 Screw on Face Plate
1
7
03011127
M5*8 Screw for UL-NS75 &- NS150
*
8
02021036
O-Ring for Face Plate (UL-NS75)
1
8
02021028
O-Ring for Face Plate (UL-NS150)
1
9
03011149
M6*40 Mounting screw
4
10
01051171
Mounting Bracket for UL-NS75
1
10
01051172
Mounting Bracket for UL-NS150
1
11
02011158
Gasket
2
12
89043702
Wall Bracket
1
P13 SPARE PART LIST
2
3
4
5
6
7
8
9
10
11
12

Underwater Light Series
TABLE OF
CONTENT
PAGE
2
....
2
7
....
....
3
....
P1 CONTENT
1. IMPORTANT SAFETY AND INSTALLATION INSTRUCTIONS
2. PRODUCT INTRODUCTION
2.1 TRANSFORMER+LIGHTS
2.2 CONTROL BOX+TRANSFORMER+LIGHTS
3. LIGHT SPECIFICATION
3.1 ELECTRICAL
3.2 COLOR MODE
4. INSTALLATION NOTES
5. LAMP INSTALLATION
5.1 Preparing to Install
5.2 UL-P100 LED-P100 UL-CP100 LED-CP100 UL-NS75/150 INSTALLATION
6. MAINTENANCE OF THE LIGHTS
7. SPARE PART LIST
4
....
5
....
6
....
P100/TP100/CP100/NS SERIES
8. TERMS OF THE WARRANTY
As original purchaser of this equipment have purchased from Emaux Water Technology Co Ltd, through
Authorized International Distributor or Dealer, warrants its products free from defects in materials and
workmanship under normal use during warranty period. The warranty period begins on the day of purchase and
extends only to the original purchaser. It is not transferable to anyone who subsequently purchases the product
from you. It excludes all expendable parts.
During the warranty period, Emaux authorized reseller will repair or replace defective parts with new parts or, at
the option of Emaux, serviceable used parts that are equivalent or superior to new parts in performance.
This Limited Warranty extends only to products purchased from Emaux authorized reseller. This Limited
Warranty does not extend to any product that has been damaged or rendered defective
1. as a result of accident, misuse or abuse;
2. as a result of an act of God;
3. by operation outside the usage parameters stated herein;
4. by the use of parts not manufactured or sold by Emaux;
5. by modification of the product;
6. as a result of war or terrorist attack; or
7. as a result of service by anyone other than Emaux authorized reseller or authorized agent.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, EMAUX MAKES NO OTHER WARRANTIES EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. EMAUX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY
IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS EXPRESS LIMITED
WARRANTY.
TERMS OF THE WARRANTY P14
14
.... 8. TERMS OF THE WARRANTY

UNDERWATER LIGHT SERIES
UL-P100 LED-P100 UL-TP100 LED-TP100
UL-CP100 LED-CP100 UL-NS75/150
Installation and Operation manual
USER MANUAL
STRIVE FOR CLEAR WATER
EMAUX WATER TECHNOLOGY CO., LTD
www.emauxgroup.com
SAA
EMPU21080641
IP68