emaux NP300 Series User manual

~-----~emaux
water technology -------------....
NP300 Series Underwater Light
User
Manual
General Information
r Neverinstall in verticalpositionwith the lamp facing upwardsI downwards,
r
Intended forfresh & salt water swimming pool
A) Ensure thatthe electrical system ofyour pool conforms to the following requirements of all
local codes
and ordinances. A licensed or certified electrician must install the electrical
system to
meet or exceed those requirements before the niche (fixture-housing) is
installed.
B) Installation Guideline:
1) The top of the lightlens be at least 18 inches (457mm) below the water level.Someinstallers
position
the niche 24 inches (610mm) below anticipated water level to avoid any
inspectionauthority issues withthis requirement.
2) The lighting circuit must have a Ground Fault Circuit Interrupter (GFCI), and an
appropriately rated circuitbreaker.
3) The junction box or the low voltage transformer is located at least8 inches (203mm) above
water level and . at least 48 inches (1912mm) from the edge of the pool
4) The light fixture and all metal items within 5 feet (1534mm) of the pool must be properly
electrically
bonded.
5) The niche must be properly installed so
that the "Top" sign inside is at the 12
o'clock position and that the top edge of
the underwater light's lens is at least 18
inches (457mm) below the surface of the
water in the pool
To GFCI , CircuitBreaker
and Power Source
6) The niche is properly electrically bonded
and grounded via a ground connector located
at the rear of the niche
C) Terminal Block must meet the IEC60988-2-1
standard having the rated connecting
capacity of
49•
Installation Diagram for NP300
1-4
EM ll 160229SO

~-----~Erliaux
water technology ------ ------ -...
4.0mm2, use of screw type terminal at least 25A rated current, mounted inside junction
boxes, seethefigure1below
D)
Use only EMAUX lighting fi x tures in this niche to Screw Type
Terminal Figure 1
ensure proper bonding and grounding AC 12v [ I J
connections. ---....- r:r:1 =:::® Lamp
0(For US user, please also follow the requirements
of the Nat i onal El ectrica l Code (NEC)
Ni c he Installation --------~
Concret .e swimming pool
l ) To installt he un derwater lightingin a concrete swimming
pool, the ni che sh ould be fixed in the wa ll of t he
swimming pool. Be su re the top of the niche be at least
18 inches (457mm)
below the water l eve l. and t he TOP
sign of thenicheis at the 12 o'clock position.
Underwater
Light Fixture
2) There are two conduits at the back of the niche, please
chose
one which is most convenient to your wiri ng design
and sealtheother one with theplugprovi ded.
3) Concret i ng the poo l as shown in figure 2.
Concrete swimming pool with vinyl liner
Ni che
Figure 2
l) To install the underwater lighting in a concrete swimming pool with vinyl liner, the ni che should
be fixed in the wall of the swimmi ng poo l. Be sure the top of the ni che be at least 18 inches
(457mm) be l ow the water l eve l, and the TOP si gn of theni che is at the 12o' clock position.
2)There aret
wo conduits at the back of the niche, please chose one wh ich ismost co nveni ent to
yourwi ri ng design and seal the other one withtheplugprovided.
3)Punchor dr ill theholesin the vinylliner as statedin figure 3.
4) Ins tallthe Ni che as shown infigure 4.
20-06mm
Vi n yl Line r Gasket
0235mm
Co ncr ete
Figure 3 Figure 4
2-4

~-----~Einaux
watertechnology ----- --- ----
Installation of the stainless steel or plastic lid
1) Remove the old lid by unscrewing the two
M6 screw on the lid. Note that the 0 ring,
nuts slide
block and the fastening dog will
be loosen too by removing the M6 screws
on the lid, as shownin figure 5.
2) Install the new plastic lid or stainless steel lid
as shown in figure
6, make su re the screws
ho le are aligned. Fasten the M6 screw on
the lid.
Underwater light fixture installation
I
Figur e 5
I
Figure 6
1) Feed cord through conduit to junction box, leaving at least 59 inches (1500mm) of cord at
the light fixture to coil around the back of the light, such that the light fixture would be
bought back to the pool deck forservice.
2) Make thewire connection to thejunctionbox.
3) Insert the entire unc::lerwaterlightfixture into the niche. In order to obtain good poollighting
it
is important that the company logo of Emaux of thelid is located onthe6 o'clock position.
4) Screw in the two M6x 75 screws on thelid until thefastening dog is secured in the innerwalls
Figure 7
Lamp Replacement
of the niche as shown in figure 7.
5) Before operating the light for more than 10 seconds, fi ll the
poo l with wa ter until the underwater li ght is comp letely
submerged
in water. To check for properoperation, turn on
main street or circuit breaker
as we ll as ·the switch t hat
operatestheunderwaterlightitsel f.
1) To remove the underwater light to the pool deck, loosen the two screws on the lid until
the fastening dog yields sufficiently so that the underwater lightunit can be separated
from the niche .
2) Unscrew the 6nuts which secure the lid to the base of the underwater lightasshown in
figure 8.
..
Figure 8
3-4

~-----~Eniaux
watertechnology --------------
3) Remove the lamp and gasket from the inside of the
base of the underwater light by disconnecting the
two terminals, loosening the two screws which secure
them to the lamp,seeFigure9.
4) Change the lamp and assemble the Underwaterlight,
in the opposite order described, taking special care
to:
0Connect the cable terminals to the lamp, using
the 2 screws supplied with the lamp,see Figure
10.
0Fully centre the gasket in its seat.
0Firmlytighten
the nuts.
0Before lamp replacement, ensure the power to
the underwater light is cut off.
Figure 9
01n order to ensure full wat er tightness, Discard
the old Gasket and replace itwith a new one.
Figure 10
REPLACEMENT PARTS
Key Part No.
Description
No. -
1 03011326 M6*80 Screws
2 01050025 Plastic Lid
(B l ank)
2 01050008 Plastic Lid (EMAUX)
->-
2 89041609 Stainl
ess Steel Lid (EMAUX)
I-
-
2 89041610 St ain l ess Steel Lid (Blank)
3 03011327
__ M6*55 Hexagon Head Screws
4
>----
01 10001 1 Face Ri ng
5 04011004 PAR56
Light Bulb (Y ellow Light ) (Standard Bulb)
5 04011043 Por56 252
LED Bulbs (Whi te-Colour)
I-
.__
5 04011044 P
or56 252 LED Bulbs (Blue Colour)
5 04011045 P
or56 252 LED Bulbs (Wi th Remote Control)
....
Gasket
·-
5 04011056 P or56 (252 LED Bu lbs) 12V /16W (Auto matic Colour Change)
5 04011047 Por56 144 L ED Bulbs (Whi te Co lou r)
5 04011048 Por56
144 L ED Bulbs (Blue Colour)
5 04011049 Por56 144 LED Bulbs (Auto Co l our Change )
-
6 02020038
Waterproof 0- R ing for bulb
>---
-
7 01230003
Waterproof Cover
8 89041601
Waterproof 0-Ring with To oth Hea d for Cab le
9 89041602 Nut F itt ing
10
89041603 Fastening Dog
11 89041604 Water Joint Fi ttings for Coble
12 89041606 NP300 Lights Coble 2.5m
13 89041608 Vinyl Pool fi tting for NP300
14 01050010 NP300 LightsN iche
15 89041605 P lug with 0-Ring
16 01171106 Jo in t for wire & pipe
4-4
·-
Qty
-
2
1
1
1
1
-
6 -
1
-
1
1
1
1
1
1
1
·-
1
1
1
1
6
2
1
1
1
1
1
1