emaux E-Lumen X Series User manual

www.emauxgroup.com
SAA
USER MANUAL
E-Lumen X SERIES
TOPAZ Installation and Operation manual
EMAUX WATER TECHNOLOGY CO., LTD
ADDRESS FLAT A-D, 20/F., KAI BO 22, 22 WING KIN ROAD,
KWAI CHUNG, HONG KONG
PHONE [phone]
STRIVE FOR CLEAR WATER
EMLI21030502

E-LUMEN X SERIES
TOPAZ Installation and Operation manual
TABLE OF
CONTENT
PAGE
3
....
3
....
5
....
P2 CONTENT
1. IMPORTANT SAFETY AND INSTALLATION INSTRUCTIONS
2. PRODUCT INTRODUCTION
2.1 BASIC ON/OFF MODE
2.2 COLORTOUCH MODE
3. LIGHT SPECIFICATION
3.1 ELECTRICAL
3.2 DIMENSIONS
3.3 COLOR MODE
4. INSTALLATION
4.1 WIRING DIAGRAM
6
....
5. LAMP INSTALLATION
5.1 TOP13-C CONCRETE POOL
5.2 TOP13-VL
5.3 TOP13-VS
7
....
6. MAINTENANCE OF THE LIGHTS
12
....
13
.... 7. SPARE PART LIST
8. TERMS OF THE WARRANTY
15
....
TERMS OF THE WARRANTY P15
8. TERMS OF THE WARRANTY
As original purchaser of this equipment have purchased from Emaux Water
Technology Co Ltd, through Authorized International Distributor or Dealer,
warrants its products free from defects in materials and workmanship under
normal use during warranty period. The warranty period begins on the day of
purchase and extends only to the original purchaser. It is not transferable to
anyone who subsequently purchases the product from you. It excludes all
expendable parts.
During the warranty period, Emaux authorized reseller will repair or replace
defective parts with new parts or, at the option of Emaux, serviceable used parts
that are equivalent or superior to new parts in performance.
This Limited Warranty extends only to products purchased from Emaux
authorized reseller. This Limited Warranty does not extend to any product that
has been damaged or rendered defective
1. as a result of accident, misuse or abuse;
2. as a result of an act of God;
3. by operation outside the usage parameters stated herein;
4. by the use of parts not manufactured or sold by Emaux;
5. by modification of the product;
6. as a result of war or terrorist attack; or
7. as a result of service by anyone other than Emaux authorized reseller or
authorized agent.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, EMAUX MAKES NO
OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. EMAUX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS
LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY
LAW ARE LIMITED TO THE TERMS OF THIS EXPRESS LIMITED WARRANTY.

IMPORTANT SAFETY AND INSTALLATION INSTRUCTIONS P3
1. IMPORTANT SAFETY AND INSTALLATION INSTRUCTIONS
Please read the manual carefully before commencing installation. This manual contains
important information about the correct installation and operation of TOPAZ lights.
1. Only qualified electrician is allowed to carry out the installation of this product.
2. Avoid direct contact with electrical power.
3. Respect all regulations in effect for preventing accidents.
4. All units are required to be disconnected from the main electricity before any operation of
maintenance.
5. For safe and proper installation, ensure that those parts supplied with the produce are used.
6. Never handle with wet hands and feet.
7. This unit is design for use only when fully submerged in fresh water, connecting with a safety
transformer
8. This product should be installed according to your local electrical installation ordinances and
regulations.
9. Due to the corrosive nature of unbalanced pool chemicals, please keep you pool water is acid-
base balanced prior to installation, and ensure the longevity of these lights.
10. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in order to avoid
a hazard.
11. Check that there is enough cable behind light to allow for servicing above water, preferably at
ground-level pool-side.
12. Never operate this Underwater Light for more than 1 minute unless it is totally submerged in
water.
13. You lights require cleaning at any time, be sure to a mild detergent or other ways that don't
damage to the lights.
14. Be sure power is off before installing or removing LED plate. Allow LED plate to cool before
replacing.
15. Maximum Depth for Light installation at 1.2 meter.
16. Maximum Water Temperature Range for light operation 0-25°C
For non replacable lightsources: ”The light source of this luminaire is not replaceable; when the
light source reaches its end of life the whole luminaire shall be replaced”.
For operation only with safety isolating transformer conforming with AS/NZS 61558 series.
2. PRODUCT INTRODUCTION
The wall mount retrofit swimming pool underwater light is designed to latest LED lighting
technology. There are two 30 second self-determine operating mode which is fully compatible to
50Hz or 60Hz input voltage frequency. When the lights use the same power source, they will be
self-synchronize during color change mode without color alignment reset. The light include RGB
color LED, individual warm and cool white, 5 different LED color in total. The two mode can't be
applied at the same time.
P14 SPARE PART LIST
TOP13-VL / TOP13-VS
Key No. Part No. Description QTY
1-1 112010111
440547998
440647771
440647772
112362743
440517766
E042701
E042702
105107997
E042703
02021091
440017769
440087767
440087768
E042704
Screw M3*18.5(316)
15 LEDs Panel 13W Color
Fastener Left
Fastener Right
M3*8 screw 316
Face Plate
15 LEDs Panel Suite 13W Color for TOP13-VL/VS(Composition of 1-1,1-2,1-3,1-4,1-5,1-6)
Retro-fit Connector(For TOPAZ, with cable 2.5m)
Cable 2.5m(For TOPAZ)
TOP13-VL/VS Water Joint Fittings for Cable
Rubber Ring
Nut
Lights Niche TOP13-VL
Lights Niche TOP13-VS
Joint for wire & pipe Suite TOPAZ
1
1
1
1
6
1
1
1
2
1
1
1
1
1
1
1-2
1-3
1-4
1-5
2
3
4
5
6
7
1-6
1
1-3
1-4
1-5
1-6
1-5
2
3
4
5
6
7
1-1
1-2
6

P4 PRODUCT INTRODUCTION
2.1 BASIC ON/OFF MODE
When the light is connected to the transformer directly, to on/off the main switch to controls
the color changes.
2.2 COLORTOUCH MODE
It need to cooperate with Color Touch Control Box to pick up color directly and adjust
brightness. Without this control box, it will be self-determine to basic mode when 12Vac
power is connected.
*AC main switch
Zone 2 Zone 1
220-240Vac
to 12Vac
Transformer
220-240Vac
to 12Vac
Transformer
220-240Vac
to 12Vac
Transformer
220-240Vac
to 12Vac
Transformer
220-240Vac
to 12Vac
Transformer
SPARE PART LIST P13
7. SPARE PART LIST
TOP13-C
Key No. Part No. Description QTY
1-1 112010111
440547998
440647771
440647772
112362743
E042705
E042702
105107997
112010118
440647773
440427770
440087770
E042706
E042704
89041605
Screw M3*18.5(316)
15 LEDs Panel 13W Color
Fastener Left
Fastener Right
M3*8 screw 316
15 LEDs Panel Suite 13W Color for TOP13-C(Composition of 2-1,2-2,2-3,2-4)
Retro-fit Connector(For TOPAZ,with cable 2.5m)
Cable 2.5m(For TOPAZ)
M3*23 screw 316
Fastener Ring
Clamp Ring
Lights Niche
TOP13-C Water Joint Fittings for Cable
Joint for wire & pipe Suite TOPAZ
Plug with O-Ring
1
1
1
1
4
1
1
1
2
1
1
1
1
1
1
1-2
1-3
1-4
1-5
1
2
3
4
5
6
7
8
9
1-5
2
3
4
1-4
1-3
5
6
9
87
1-1
1-2

LIGHT SPECIFICATION P5
3. LIGHT SPECIFICATION
3.1 ELECTRICAL
Operation Voltage Range: AC12V (COS : 0.8 ,MAX 1.0A)
LED Color: RGB + Warm White (3000K) and Cool White (6500K)
Operation Frequency: 50/60Hz
Max Power Rating: 13W
Mode of operation: ON/OFF Mode or ColorTouch control box
There are three different installation types for TOPAZ lamp:
TOP13-C
TOP13-VS
TOP13-VL
Concrete Pool
Fiber Glass Pool
Vinyl Pool
3.2 DIMENSIONS (in mm)
3.2.1 TOP13-VL
3.2.2 TOP13-VS
3.2.3 TOP13-C
P12 MAINTENANCE OF THE LIGHTS
7. Place the lamp into the niche 8. Rotate the lamp on the fastener ring which is
auto locked
9. Apply a screw driver push to key hole to release
the lamp.
6. MAINTENANCE OF THE LIGHTS
1. Do not leave the lights “on” above water for longer than 1 minute.
2. Before switching on the lights, check whether the lights are fully submerged underwater
and the circuit boxes are running properly.
3. This unit does not need any kind of maintenance. If it is not working properly, please
contact EMAUX authorized dealer where you purchase the unit from.
4. Warranty will be voided if the Emaux Underwater Light was dismantled by unauthorized
personnel.
6. Screw the connector to the lamp with face plate5. Warp the power cord few round.
φ130.5
38.5
φ130.5
172
27
φ120
5
°
φ58
214.5
38.5
φ58
214.5

Break Conduits
Above Waterline
Junction Box
TO
Transformer
D20 PVC pipe
Break Conduits
Above Waterline
Junction Box
TO
Transformer
P6 INSTALLATION
3.2.4 Light Intensive chart
3.3 COLOR MODE
NO.
1
2
3
4
5
6
7
8
NO.
9
10
11
12
13
14
15
Mode Mode
Cool White
Green
Blue
Green+Blue
Red+Green
Red+Green+Blue
Mode A: Blue+Gradual Red
Mode B: Green+Gradual Red
Mode C: Blue+Gradual Green
Mode D: RGB Color Sequence
Mode E: RGB Color Sequence
Mode F: Auto Color Change
Mode G: RGB Color Sequence
Mode H: Rapid Auto Color Change
Warm White
4. INSTALLATION
1. It is recommended to install a light every 20 , the approximate exposure area of each unit.
2. The lights should be installed in the direction that they will not shine directly into the
house.
3. For training or competition pools, the lights must be installed on the sides in order to
prevent swimmers from seeing any glare.
4. Nothing should be placed on the pool side directly above the lights for ease of future
maintenance.
5. The cables connecting the lights and the transformers must be at least 6mm² and the
distance between them must not exceed 30m; otherwise the lights will not function
properly.
6. Terminal blocks must meet the IEC60988-2-1 standard having the rated connecting capacity
of 4,0mm² use of screw-type terminal at least 25A current rating, mounted on junction
boxes inside.
m² 3. Screw the nut tight from inside 4. lead the power cord with connector though
the niche from the front side.
LAMP INSTALLATION P11
1. Opening Hole
Installation Step:
TOP13-VLTOP13-VS
2. Insert the light niche through the opening
with plastic ring on both face side.
TOPAZ
0.00m
1.00m
2.00m
3.00m
4.00m
5.00m
6.00m
7.00m
Φ60mm
Φ60-65mm
O-ring

Sealant
Pool Finish
20mm(MAX)
10mm(MIN)
68mm(MAX)
50mm(MIN)
125mm(standard)
50mm
Minimum
Concrete
Coverage
Concrete Thickness
Concrete
Reinforcing
Bars
Junction Box Break Conduits
Above Waterline
D20 PVC pipe
Soil
Water Line
To
Transformer
40mm
(MIN)
90mm
(MIN)
Pool Finish
20mm(MAX)
10mm(MIN)
68mm(MAX)
50mm(MIN)
50mm
Minimum
Concrete
Coverage
Concrete Thickness
Sealant
Concrete
Reinforcing
Bars
Junction Box Break Conduits
Above Waterline
D20 PVC pipe
Soil
Water Line
To
Transformer
450mm(MIN)
125mm(standard)
Lamp Installation P7
4.1 WIRING DIAGRAM
Basic ON/OFF Model wiring ColorTouch Mode
ColorTouch Control Box PCB
Zone 1
Power cord
Zone 2
Power cord
AC Mains
Power cord
5. LAMP INSTALLATION
5.1 TOP13-C CONCRETE POOL
Typical vertical and horizontal concrete pool installation layout is illustrated as below diagram
for reference.
P10 LAMP INSTALLATION
8. Apply a screw driver push to key hole to release
the lamp .
5.2 TOP13-VL
5.3 TOP13-VS
Junction Box Break Conduits
Above Waterline
To
Transformer
Junction Box
D20 PVC pipe
To
Transformer
Break Conduits
Above Waterline

P8 LAMP INSTALLATION
1. Mounting the niche on steel reinforced bar.
Installation Step:
LAMP INSTALLATION P9
2. The niche and the concrete wall should be seal
with sealant to prevent water get inside.
3. Lead the power cord with connector through
the niche
4. Insert the clamp ring into the niche before
ceramic is applied. Wrap the power cord few
round 5. Assemble the power cord
6. Screw the Fastener Ring on the clamp ring 7. Rotate the lamp on the fastener ring which
is auto locked
Vertical PVC Conduit
Horizontal PVC Conduit D20 PVC Conduit
125mm
Steel Reinforce Bar Sealant
92mm
5°
125mm(standard)
Concrete
Reinforcing
Bars
Pool Finish
20mm(MAX)
10mm(MIN)
68mm(MAX)
50mm(MIN)
50mm
Minimum
Concrete
Coverage
Concrete Thickness
Sealant
Break Conduits
Above Waterline
Junction Box
Hosepipe
Soil
Water Line
To
Transformer
450mm(MIN)
27mm
Cable And Screw Nut
10-20mm ceramic