emaux P50 User manual

SOLUCIONES
RUC: 20523056167
www.cubaspa.com.pe
[phone] / 998119929
CALENTADOR
ELÉCTRICO
C-SPA 9KW
Description
The EMAUX Plastic Spa Light is durable, easily installed underwater light for
pool and spa. Especially designed for pool and spas, it provides
breathtaking color at the ip of a switch. it is a must for nighttime pool
safety and enjoyment. It can also enhance your pool and spa's beauty and
help create an inviting backyard environment after the sun goes down.
EMAUX P50
Plastic Spa Light
Unpacking INSTALLATION
When unpacking the unit, inspect (For vinyl and berglass swimming
carefully for any damage that may pool only)
have occurred during transit. Check A. Preparatory steps
for missing accessories or damaged 1) Ensure that the electrical system
parts. Transit damage claims should and its wiring for the pool conform
be made to the shipping company. to the requirements of your
Specications govenment or your local
(For Plastic Spa Light only) authorities. The installa-tion of the
Model: 88041101, 88040101 Underwater Light should only be 4) The mounting bracket must be
per-formed by a licensed properly instal-led so that the
electrician. top edge of the Underwater
Light lens is at least 45CM below
2) The junction box, or the low
the surface of the water in the
voltage transfor-mer for 12 volt
pool, see Figure 1.
Underwater Light model is to be
5) Consult the local Government
located at least 120CM from
Building Departm-ent to be
the edge of the pool, see Figure 1.
certain that the pool's electrical
3) The light xture and all metal
system .meets all applicable
parts that are within 240CM of
requirements.
the pool must be properly
RISK OF ELECTRICAL SHOCK OR 6) The underwater light should be
protected with non-ductile
ELECTROCUTION installed on a at and rigid
materials and that the
This underwater light xture must be surface.
connections must be waterproof.
installed by a licensed or certied
electrician or a qualied serviceman
in accordance to the requirements
of your government standard or
local authorities. Improper installation
will create electric hazards which
could result in serious injury, death as
well as damage to the property.
Before servicing the light, disconnect
the power supply from the circuit
breaker. Failure to do so could result
in serious injury, death or damage to
the property.
DANGER
Ф
Figure 1.
FICHA TÉCNICA

SOLUCIONES
RUC: 20523056167
www.cubaspa.com.pe
[phone] / 998119929
B) INSTALLATION for more than 10 seconds,
1) Punch or drill a hole ll the pool with water until
(Diameter = 62mm) in the the underwater light is
desired location on the completely submerged in
pool wall, see Figure 1. Be water. To check for proper
sure the top of the hole be operation, turn on main
at least 18 inches below switch or circuit breaker as
the water level. well as the switch that
2) Put a O-ring on the pool operates the underwater
wall and then feed the light itself.
cord throught the hole.
3) Use the nut provided to x
the underwater light on the A) Never operate this
pool wall, as shown in Underwater Light for more
Fugure 2. than 10 seconds unless it is
totally submerged in water.
Without total submersion,
the light assembly will get
extremely hot, which may
result in serious injury to
pool users, installers, or
damage to property.
B) Be sure power is off before
installing or removing lamp.
Allow lamp to cool before
relamping. This light xture
uses a Halogen Quartz
4) Feed cord to junction box, lamp. Do Not touch lamp
strip 6 inches of the outer with bare hand, this may
cord jacket to expose the severely reduce its life. Use
insulation wires and make the plastic furnished with
the wire connection to the the replacement lamp to
junction box. eliminate nger prints from
5) Secure the junction box getting on lamp.
cover in place.
6) Before operating the light
EMAUX P50 Plastic Spa Light
WARNING
Figure 2.

SOLUCIONES
RUC: 20523056167
www.cubaspa.com.pe
[phone] / 998119929
1
2
4
3
5
6
7
8
9
Figure 3 – Repair Parts Illustration for Plastic Spa Light
Repair Parts list for Plastic Spa Light
Repair Parts list for Plastic Spa Light
Key No. Part No. Description Qty
1* 01221001 P50 Light Colour Lens (Red+Green+Blue) 1
1* 01221001C UL-P50 Light Colour Lens (Clear) 1
2 01041019 Inside Covers for P50 Lights 1
3 02021010 O-Ring 1
4 04011001 Halogen lamp MR16 AC 12V/20W for UL-P50 1
4 04011016 LED-P50 lamp 12V/1W (Automatic Colour-Changing) 1
4 04011015 LED-P50 lamp 12V/1W (White Colour Only) 1
5 02021000 O-ring for Encasing 2
6 89041101 P50 Lights Encasing Set 1
7 01021007 Nut 1
8 89041102 Connector with Gasket for Cable 1
9 04013001 Lights Cable 1.5M for P50 1
Notes:1* 01221001 is UL-P50 Light Colour Len 1 set with (Red+Greee+Blue) or
1* 01221001C is UL-P50 Light Colour Len with (Clear)