Erreka ARES Operating instructions

9
ARES
Quick installation and programming guide English
IMPORTANT
NOTE
This quick guide is a summary of the complete installation manual. The manual contains safety warnings
and other explanations which must be taken into account. The installation manual can be downloaded by
going to the "Downloads" section at the Erreka website:
http://www.erreka.com/Automatismos/descargaDocumentos.aspx
Elements of the complete installation
Electrical cabling
A: Main power supply
B: Flashing light
C: Photocells (Tx / Rx)
D: Pushbutton or key switch
E: Operator
F: Antenna
Limits on use
AE33IPL-AE33DPL
AE3324I-AE3324D
We recommend using an electrolock for leaf
lengths of over 1.8m.
Values for orientation purposes. The form of the
leaf and the presence of strong wind may bring
notable differences in the values of the chart.
BGRBI-BGRBD; BGRBIM-BGRBDM;
BGRRI-BGRRD
BGRBIL-BGRBDL;
BGRRIL-BGRRDL

10
Short operator, inward opening (run: 300 mm)
A (cm) B (cm) C (º)
140 140 95
120 160 120
Long operator, inward opening (run: 400 mm)
A (cm) B (cm) C (º)
190 190 95
135 185 120
Short operator, outward opening (run: 300 mm)
A (cm) B (cm) C (º)
140 140 95
120 160 120
Long operator, outward opening (run: 400 mm)
A (cm) B (cm) C (º)
190 190 95
135 185 120
Levels A and B determine the opening angle C.
Assembly positions and levels

11
C137B
Components supplied Manual drive
Unlocking
(manual operation)
Locking
(motorised operation)
D137A
1
1
1 Mount the wall support
Assembly
2 Mount the operator on the wall support
3 Position the gate support 4 Mount the operator on the gate support
The supports should be
positioned so as the operator
forms an angle of 1° with
regards to the horizontal,
remaining lower on the gate
support side.

12
ST1
FT1
P1 P2 P3
ST2
FT2
P4 P5 P6
STOP
P7 P8 P11
P12
LOCK
FCA1
FCC1
P15 P14 P16
P22 P23
Courtesy
Light La p.
G7 G8 G9 G10
24Vac
G4 G5 G6 G1 G2 G3
FCA2 COM FCC2 SCA
P169V
VIVO-M201: 230Vac/50Hz
VIVO-M201M: 125Vac/60Hz
NL
POWER
MOTOR2 (G2-G1-COM) MOTOR1 (G2-G1-COM)
G4 G5 G6 G1 G2 G3
A1, A2 Operators
C1, C2 Capacitors
DL4 Gate opening
DL5: Gate closing
PUL1 Close mini-pushbutton
PUL2 Open mini-pushbutton
TEarth connection
Operator connections A1 / A2:
G1 / G4 Open
G2 / G5 Close
G3 / G6 Common (COM), grey cable
When pressing PUL1, DL5 lights up and
the G2/G5 and G3/G6 cable
connectors are activated.
When pressing PUL2, DL4 lights up and
the G1/G4 and G3/G6 cable
connectors are activated.
Electrical connections (except AE3324I and AE3324D)
We recommend using the VIVO-M101(M) switchboard (for single operator installations) and
VIVO-M201(M) (for twin operator installations).
ST1 FT1
P1 P2 P3
WARNING
LIGHT
P9 P10
24V
ST2 FT2
P4 P5 P6
STOP
P7 P8
GND
+
G4 G5
GND
NL
SW1
V+
P13
SNG1
P14 P15
SNG2
P16
GND
V+
P17
SNG1
P18 P19
SNG2
P20 P21 P22 P23
ENCODER1 ENCODER2
MOTOR2
G1 G2
GND
MOTOR1
P11 P12
LOCK
POWER - 230V
CN13
G6
G3 G7 G8
Courtesy
Light
La p.
G9 G10
-FT
(Test)
AUX
24 Vdc
P24 P25
EDGE
P144Y2
VIVO-D201:
VIVO-D201M:
A1 Operator 1
A2 Operator 2
G1/G4 Red cable (motor)
G2/G5 Blue cable (motor)
SW1 Main switch
•Select the number of operators using C0 (C001: one operator, C002: two operators).
•Select the directions using C1 (A1) and C2 (A2).
•Programme C7 for operation without encoder or limit switches (C700).
•For the ARES 24V operator, programme C304.
•Adjust the thrust in accordance with the weight of the gate (parameter A6).
Electrical connections (AE3324I and AE3324D)
Turning direction check: after connecting the power and activating any of the key devices, the
gate makes a reset (the display showsrS): the gate closes until it reaches the stopper, assigning this
stopper with the position "gate closed" If it opens instead of closes during the reset, change turning
direction using C1 (A1) or C2 (A2).
We recommend
switchboard
VIVO-D201(M).