Erreka LINCE Operating instructions

5
LINCE
Quick installation and programming guide English
WARNING
This quick guide is a summary of the complete installation manual. The manual contains safety warnings and
other explanations which must be taken into account. The most recent version of this guide and the
installation manual are available at the "Downloads" section on Erreka's website:
http://www.erreka-automation.com
The options and functions described in this guide apply for the firmware version indicated on the circuit. The
firmware, as part of a process of continuous improvement, is subject to new functionalities or upgrades being
included as a result of new versions which are not necessarily compatible with previous ones. For this reason,
some options or functions may differ or be unavailable if your firmware is older than shown in this guide.
Electrical cabling
A: Main power supply
B: Flashing light
C: Photocells (Tx / Rx)
D: Pushbutton/wall key
E: Antenna
E71A
C71A
OBEWARE: the base plate is not
symmetric (a > b)
Elements of the complete installation
Assembly levels
D71A D71B
Unlocking
Motorised operation locking:
•Turn the handle (2) anti-clockwise 270°, through to
the stopper.
•Push the cylinder (3) inward and manually move the
gate to interlock it in the drive mechanism.
•Activate a key device in order for the gate to carry out
a "reset".
Unlocking Locking
Unlocking for manual operation:
•Insert the key (1) and turn clockwise 90º, without
forcing it: the cylinder will protrude a few millimetres.
•Turn the key anti-clockwise 90º and remove.
•Turn the handle (2) clockwise 270°, through to the
stopper.
Firmware V4.6 or later

6
General connections
L:Line
N: Neutral
T: Earth
F:Mainfuse
230VAC: 2,5A
125VAC: 4A
Disconnect the power
supply before connecting
or disconnecting any
component.
DL13 24Vac power supply
DL36 5Vdc power supply
DL37 Closing relay activated
DL38 Opening relay activated
M17C
D1 and D2:
CL (static) Gate closed
CL (flashing) Gate closed
OP (static) Gate open
OP (flashing) Gate opening
PC (flashing) Pedestrian gate closing
PO (static) Pedestrian gate open
PO (flashing) Pedestrian gate opening
XX (countdown) Gate on standby
STOP Actuator unlocked
PA (static) Pause (operation not complete)
rS (flashing) Gate searching for close position
D3 and D4:
C4 Opening safety device activated
C5 Closing safety device activated
E1 Encoder motor halted
F1 Force limit exceeded
bA (static) Battery working
bA (flashing) Battery voltage too low (the board
does not carry out any operations)
Ftço Photocells defective (testing)
Display indications

7
P71Y
P71X
P71Z
Rotation direction change and check (C1)
P71V
P71W
This operation is only necessary if the operator opens the leaf instead of closing it when making a reset (rS).
I
II
P157E
 I f a receiver other than
RSD is used, see the
corresponding
instructions.
Select the option C801
(RSD receiver) before
programming.
Total opening radio code programming, P1 (with RSD receiver only, C801)
Pedestrian opening radio code programming, P2 (with RSD receiver only, C801)
This procedure is the same as for total opening, but using parameter P2 instead of P1.
I
II
OWait whilst the gate
carries out the travel
Travel recording (P3)

8
Complete programming chart
D1 D2 Parameter D3 D4
Pre-
determined
option
Options or values
C1Motor rotation direction 01x
02
4Opening safety device (photocell or strip) 00xDevice not installed
10 Device without testing
11 Device with testing
5Closing safety device (photocell or strip)
Closing photocell with C520 or C521, also
prevents the gate from opening
00xDevice not installed
10 Device without testing
11 Device with testing
20 Device without testing
21 Device with testing
8Radio receiver 01 RSD card (non-decoding)
02xTwin-channel decoding card
P1Total opening radio code recording oç
2Pedestrian opening radio code recording oç
3Gate travel recording oç
F1Operation mode 01 Automatic
02xSemi-automatic
2Standby in automatic mode 0...5ÿ 0...915 59= 59 sec; 2ÿ5 = 2 min. 50 sec, etc
3Pedestrian opening 00xPedestrian opening is not carried out
10 10% of total opening
20 20% of total opening
30 30% of total opening
40 40% of total opening
50 50% of total opening
A0Flashing light 01xNo warning
02 With warning
1Garage light time 0...5ÿ 0...903 59= 59 sec; 2ÿ5 = 2 min. 50 sec, etc
2Gate speed 01...505 01: minimum speed; 05: maximum speed
3Soft stop speed 01...503 01: minimum speed; 05: maximum speed
4Soft stop function 00...501 00 : minimum distance; 05 : maximum distance
5Recede after closing (allows offsetting of gate
expansion)
A50x: Stops in the selected position without
making contact
A51x: Makes contact and moves back to the
selected position
0...10...904 x0: no recede;
x9: maximum recede
6Maximum force 0...10...908 01: minimum force; 10: maximum force
7Closing photocell used during standby (in
automatic mode only)
01 Immediate close
02xRestart standby time
03 Has no effect
8Pushbutton operation during standby (in
automatic mode only)
01 Immediate close
02xRestart standby time
03 Has no effect
9Opening mode 01xOpening in accordance with the mode
selected in the main functions (F)
02 Community opening (the control panel
does not obey the commands during
opening)
03
Step-by-step opening (the gate halts if an
operation device is activated during opening.
The gate closes when operated again)
ç1Operations carried out XX Indicates the hundreds of cycles
completed (for example, 68 indicates
6,800 cycles completed)