Erreka NAOS Operating instructions

11
NAOS
Quick installation and programming guide English
WARNING
This quick guide is a summary of the complete installation manual. The manual contains safety warnings and
other explanations which must be taken into account. You can download the installation manual in the
"Downloads" section of the Erreka website:
http://www.erreka-automation.com
I260B
Elements of the complete installation
Electrical wiring
A: Main power supply
B: Closing photocells
C: Pushbutton/wall key
D: LUMI flashing light
Assembly levels
Level H: the track should remain 10
cm above the highest point of the
door (see detail H ).
Total length (operator + guide) and
effective travel:
– track ref. ANA01; pos J:
3502 mm / 2741 mm
– track ref. ANA01; pos K:
3452mm / 2,691mm
– track ref. ANA02; pos J:
4602mm / 3,841mm
– track ref. ANA02; pos K:
4552mm / 3,791mm
Disconnect the power supply before connecting
or disconnecting any component.
A.T., S and STOP devices must be voltage-free in
order to prevent any damage to the control board.
A.T. Wall key or button
SClosing safety device (closing photocell)
AUX Power supply for peripherals (24 Vdc)
STOP Emergency shutdown
LAMP Warning light (24 Vdc)
Battery connection using sp+ and sp- wire
connectors (inside the frame). Charger CHG01 is
required (included in kit ADO01 with 12V 1.2Ah
batteries).
P260M
Electrical connections
Unlocking
Manual operation unlocking: pull the knob or cable
(1) until the release lever (2) is vertical.
Motorised operation locking: place the lever in
horizontal position (3). Locking will take place when the
operator starts up.
D260C
3
MSP-029/01

12
P260C1
P260A
0º /180º
1
2
1
2
P260B
3
4
P260D
5
5
6
7
8
P260E
Assembly
1
Secure the track (1) in the operator (2). This can be
placed in two different positions (0º/180º); choose the
one you prefer.
2
Position the overhead strips (3) and front support (4).
Bear in mind assembly level H(see “assembly levels”
on the previous page).
3
Mount the track (1) + operator (2) on the supports (3) and (4).
4
Position the anchor (5) in the upper part of the door and couple it to
the carriage (8) using the arms (6) and (7).
5
Make the chain taut: tighten the nut
as far as possible, and then loosen it
slightly until the bushing can be
turned by hand.
OThe track (1) must be horizontal.

13
6
Install the central support (9).
7
Open the door and install the opening stopper
(10) until it comes up against the carriage (11). Use
two self-drilling, self-tapping screws.

THE OPENING STOPPER MUST BE CORRECTLY INSTALLED (10), as the carriage must come up
against it when programming the travel. If this is not the case, the operation will not be
programmed correctly.
H260A
2
s. x1
2
s.
Radio code programming
Release CODE and press the button of the transmitter to be
programmed again.
The display flashes and the operator buzzes to confirm
programming.
Press CODE for at least 2 seconds. F,
ror r. lights up in accordance with
the type of transmitter to be
programmed.
Ensure that the
operator is
programmed to
store the type of
transmitter to be
used: fixed code (F),
standard roller code
(r) or personalised
(r.) (see “STEP 6” on
page 14
).
The memory can store up to 20 different codes. To completely delete the memory, press CODE
for 5 seconds.All transmitters are deleted.
M260A1
Keep SET
pressed
down until
1appears.
STEP 1
Store door
open
position
Parameter programming
Release SET
Press SET to save the position
Programming is only accessible with the door shut-down. It is not accessible
with the door opening, closing or timed to close.
During programming, the operator does not start any operation.
Open the door through to the
opening stopper using |+ / |-

When recording open door position, IT IS ESSENTIAL TO OPEN THE DOOR
UNTIL THE CARRIAGE STOPS AGAINST THE OPENING STOPPER (10).
If this is not the case, the operation will not be programmed correctly.

14
M260B1
STEP 5
Closing
sensitivity
STEP 6
Type of
radio (fixed
or roller
code)
STEP 7
Semi-auto
or auto
closing and
standby
time
Select the value by pressing |+ / |- :
1: maximum sensitivity;
...;
6: minimum
Select mode and standby time by
pressing |+ / |- :
00: semi-auto; 01: auto, 1s; ...;
30: auto, 30s; 1.0: auto, 1 min;
1.1: auto, 1 min 10s; ...;
4.0: auto, 4 min
Press |+ / |- to select fixed code (F)
or roller code (r). The code can be
personalised by enabling the
transmitter seed (bridge or button)
of the personalised transmitter
whilst ris flashing. The display will
show r. The memory must be
empty in order to change from rto
For from rto r..
STEP 4
Opening
sensitivity
Select the value by pressing |+ / |- :
1: maximum sensitivity;
...;
6: minimum
Press SET to confirm
Press SET to confirm
Press SET to confirm
Press SET to confirm
When it stops, press SET to
confirm.
Press SET again to close.
Press SET to open the door
STEP 3
Learnforces
(opening
and closing) When it has closed,
press SET to save
In steps 4 to 12, programming can be finished
early by keeping SET pressed down.
STEP 2
Store door
closed
position Press SET to save the position
Close the door through to the
closing stopper using |+ / |-

15
M260C1
STEP 11
Opening
speed
STEP 12
Closing
speed
Select the value by pressing |+ / |- :
1: minimum speed;
...
4: maximum speed
Select the value by pressing |+ / |- :
1:minimum speed;
...
4:maximum speed
Press SET to confirm
Press SET to confirm
Press SET to confirm
Press SET to confirm
END OF PROGRAMMING
STEP 8
Slowdown
distance in
closing
Select the slowdown distance by
pressing |+ / |- :
1: 50 mm (in the track);
2: 100 mm;
3: 250mm; 4: 500mm
STEP 9
Mode in
opening
Select the value by pressing |+ / |- :
0: alternative shutdown +
automatic closing optional;
1: opening without alternative
shutdown + restart standby time
STEP 10
Operation
counter
Number of operations in hundreds:
02: 200 operations,
30: 3000 operations,
1.4: 14000 operations,
max. 5.9 (59,000 operations)
Display indications during use
CL:doorclosed
CL (flashing): door closing
F1: failure due to current
E1: failure due to encoder
OP: door open
OP (flashing): door opening
30, 29, 28 ... : countdown in automatic closing
St: stop
rS (static): waiting for reset
rS (flashing): reset
C5: shutdown by closing photocell
PA: pause