Erreka MAGIC Operating instructions

5
MAGIC
Quick installation and programming guide English
WARNING
This quick guide is a summary of the complete installation manual. The manual contains safety warnings and
other explanations which must be taken into account. The installation manual can be downloaded by going
to the "Downloads" section of Erreka website:
http://www.erreka-automation.com
E248A
TC
G
*4 x 1mm2
(max. 20m)
2 x 0,75mm2
(max. 20m)
3 x 1,5mm2
(max. 30m)
2 x 0,5mm2
(max. 20m)
RG-58/U
2 x 0,5mm2
(max. 20m)
Rx: 4 x 0,5mm2 /
Tx: 2 x 0,5mm2
(max. 30m)
TA
TA
Elements of the complete installation
Electrical wiring
A: Main power supply
B: LUMI flashing light
C: Photocells (Rx/Tx)
D: Pushbutton/key switch
E: Operator *:
motor: 4x1mm2
brake: 2x1mm2
encoder: shielded cable 2x0.5mm2
F: LUMI built-in antenna
G: Electrolock
VERY IMPORTANT:
The TC closing limit switch and the TA
opening limit switches must be installed
in all cases.
*NOTE: the electrical installation of the operator can be
done correctly and straightforwardly using the cable with
AYCY8 code, which ERREKA can supply by metre. This cable
has the characteristics 4x1mm2+2x1mm2+ ((2x0.5mm2))
and was developed specifically for this use.
The electrolock is obligatory for operators without lock
(MA210 and MA250). For operators with lock, the
electrolock must be used for gate leaf lengths of over
1.8m.
MST-042/00

6
A244A1
Unlocked (only for models with brake)
Unlocked for manual operation:
•Insert the key in the lock for unlocking and turn
approximately 120º towards the side of the wall.
Lock for motorised operation:
•Turn the key again 120º away from the wall to
lock.
M248D1
M248A1
130mm
=
96mm
78mm
174mm
670mm
57mm
=
85mm
110mm
Assembly levels
For safety: A>25mm (B>45mm)
Frame dimensions
A: frame exterior: 100 mm
B: frame interior:
•aluminium gates: ERREKA
profile 100x100x5;
•iron gates: 100x100x4
profile
M248C
Template to make the orifices
1 Holes for upper profile cover
attachment
2 Holes for lock
3 Motor attachment holes
4 Holes for lower profile cover
attachment
M248B1
46mm
9,5mm
General levels

7
P248G1
9
6
P248A1 P248C1
P248B1
P248F
67
P
P248D1
P248I1
14
13
Assembly
10 With the seal (T) in place, position
the upper cover (10) so that its slot
coincides with the protrusion on
the frame (R).
11 With the seals (S) in place, position
the top stud (11) and the plate
support (12).
12 Position the angle piece (13),
respecting the height levels.
13 Tighten the gland (14).
14 Place the attachment screws and
washers (15).
15 Install the water guard (16).
1 Position the base plate (1),
respecting the height levels. 2 Using the template provided, make 4 boreholes (2) to secure the
operator with a 10.5 mm drill bit.
3 Make the 6.5-mm holes (3).
4 Only operators with lock: drill the
21-mm holes (4).
5 Make the three holes (5) to fix the
upper cover. Use a 6.5 mm drill bit. 6 Insert the operator and fit its screws (6) without tightening
them. In iron frames, insert the
P plate between the operator
and the frame.
7 Install the caps (7) to stop
water coming in.
8 Mount the lower cover (8).
9 Insert the bushing (9) in the
operator shaft and tighten the
screws (6).
Position the assembly (M) on the
base plate (1), ensuring the drag
wheel is correctly coupled.
P248H1
10
12
11
P248J1
16
15
15

8
P246Z
ENCODER1 ENCODER2
P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23
GND
V+
SNG1 SNG2
GND
V+
SNG1 SNG2
+
-FT
(Tes )
AUX
24 Vdc
ST1 FT1
P1 P2 P3
ST2 FT2
P4 P5 P6
STOP
P7 P8
WARNING
LIGHT
P9 P10
24V
P11 P12
LOCK
Lamp.
G9 G10
G7 G8
Cour esy
Ligh
G1 G2 G3
MOTOR1
G4 G5 G6
MOTOR2
CN13
NL
POWER - 230V
P24 P25
EDGE
A2
ST1 FT1
P1 P2 P3
ST2 FT2
P4 P5 P6
STOP
P7 P8
WARNING
LIGHT
P9 P10
24V
P11 P12
LOCK
ST1
V+
GND
SGN1
NL
POWER - 230V
VIVO-M203:
230V, 50Hz
VIVO-M203M:
125V, 60Hz
F4
F1
F2
F3
ST2
A1
EPS1
Electrical connections, control board VIVO-M203
M1 and M2 motor connection:
G4/G1: brown cable
G5/G2: black cable
G6/G3: grey cable
C: capacitor; MA210/ MA210F /MAS210F: 5μF; MA250/ MA250F /MAS250F: 8μF
Encoder connection (if available):
V+: red cable
GND: mesh
SGN1: blue cable
Check the control board instructions to connect the other
components and carry out programming.
EPS1
L1
COM
L2
F1
FR2
FR1
P249Y
M203: 230V/50Hz
Brake cabling by way of EPS1 (VIVO-M203, parameter Ab01)
DL1: Red LED, FR1 activation
DL2: Green LED, FR2 activation
COM: Orange cable (models with encoder)
white cable (models without encoder)
L1, L2: purple cable (models with encoder)
red cable (models without encoder)