Fermax MEET 1490 User guide

INSTALLER MANUAL
DOOR RELAY MODULE REF. 1490
INSTALLER MANUAL

2DOOR RELAY MODULE REF. 1490
Technical publication for information purposes edited by FERMAX ELECTRÓNICA S.A.U.
FERMAX ELECTRÓNICA applies a continuous improvement policy, therefore it reserves the right to modify the contents
of this document, as well as the product features hereof at any time and without prior notice. Any modication will be
reected in subsequent editions of this document.
CONGRATULATIONS FOR BUYING A QUALITY PRODUCT!
Fermax Electrónica develops and manufactures premium equipment
that meets the highest design and technology standards. We hope you
will enjoy all its features.
Code 970084I V12_20

3
DOOR RELAY MODULE REF. 1490
CONTENTS
5 TECHNICAL SPECIFICATIONS 8
4. CONFIGURATION 8
3. INSTALLATION DIAGRAMS 6
2. USAGE 5
1. DESCRIPTION 4

4DOOR RELAY MODULE REF. 1490
DESCRIPTION
The EXTERIOR DOOR RELEASE RELAY module Ref. 1490 is an optional device for
MEET outdoor panels. There are 2 relays: RELAY 1, for use with all MEET panels, and
RELAY 2, only for use with MILO 1L panels. See section 2. USAGE later.
CONEXIONES
NOTE:
To adjust the timing of the relays, move RP1 all the way to the left then turn it gradually to
the right. Once you’ve nished rotating, the LED will blink several times, according to the
time set. The more blink, the longer the time.
Do not leave the potentiometer turned all the way to the left.
• 12 V, - : 12 Vdc power input
• 485+, 485-: RS-485 connection to the outdoor panel.
• Output 1: Pushbutton input for activating relay 1.
•Output 2: Pushbutton input for activating relay 2.
•Fire: Push button input for simultaneous activation of relay 1 and relay 2.
•NC1, COM1, NO1: Relay 1 output contacts .
• NC2, COM2, NO2: Relay 2 output contacts.
• RP1: Adjusting the timing of the relays (SEE NOTE).

5
DOOR RELAY MODULE REF. 1490
USAGE
SAFETY RELAY
It prevents the door being opened by sabotaging the outdoor panel
to access the lock release cables, as the cables come out of this
module (installed inside the house or in a protected place) instead of
the outdoor panel.
SECOND LOCK RELEASE ACTIVATION
Independent activation of RELAY 2 from the monitor in the home
itself, to activate a second lock release (garage, gate, etc.).
MILO 1L PANELS
The EXTERNAL DOOR RELEASE RELAY module Ref. 1490 is used as an optional
accessory for the MEET outdoor panels, offering the following functions:
SAFETY RELAY
It prevents the door being opened by sabotaging the outdoor panel to access the lock
release cables, as the cables come out of this module (installed inside or in a protected
place) instead of the outdoor panel.
In panel versions V3.0 onwards, it is possible to congure the panel to disable its door
release button input from inside, thus increasing security.
MILO DIGITAL, KIN AND MARINE MEET OUTDOOR PANELS

6DOOR RELAY MODULE REF. 1490
STALLATION DIAGRAMS
This diagram shows how to use the Ref 1490 module as a SAFETY RELAY (AP1) and as
a SECOND LOCK RELEASE ACTIVATION (AP2).
MILO 1L PANELS
• AP1’: Main lock release (activated from the outdoor panel).
• AP1: Main lock release (activated from the module REF. 1490).
• AP2: Second lock release (activated from the module REF. 1490).
• P1: Direct activation of the AP1 lock release.
• P2: Direct activation of the AP2 lock release.
• P3: Simultaneous direct activation of the AP1 and AP2 lock releases.
NOTES:
• This diagram corresponds to outdoor panel version V2.02 and onwards.
• The outputs for AP1 and AP1’ (main lock releases) act simultaneously.
• To use the SAFETY RELAY, connect the main lock release as AP1.
• To use the SECOND LOCK RELEASE ACTIVATIONS, connect the main lock release as
AP1’ (or as AP1 if the SAFETY RELAY function is also required) and the secondary lock
release as AP2.
• Run the AP1 connection cables through a protective conduit, separate from the outdoor
panel cables.

7
DOOR RELAY MODULE REF. 1490
This diagram shows how to use the Ref. 1490 module as a SAFETY RELAY.
DIGITAL MILO, KIN AND MEET MARINE OUTDOOR PANELS
• AP1: Output for the main lock release.
•P1: Direct activation of the AP1 lock release
NOTES:
• This diagram corresponds to outdoor panel version V2.11 and onwards.
• Run the AP1 connection cables through a protective conduit, separate from the outdoor
panel cables.

8DOOR RELAY MODULE REF. 1490
TECHNICAL SPECIFICATIONS
Dimensions (mm) 114,5x57,5x34
Power supply 12 Vdc
Power consumption 1W
Características ambientales
Working temperature -40ºC ~70ºC
Relative humidity 20-80% sin condensación
CONFIGURATION
If RELAY 2 of the module is being used to activate the second lock release in installations
with a 1 L outdoor panel, each of the monitors being used to activate said relay will need
to be congured accordingly.
They can be programmed through the monitor’s web server, accessed from a computer
with an internet browser. See the monitor INSTALLATION MANUAL for more details.
1. Access the ADVAN-
CED section.
2. Select 1, from the
drop-down list NO. OF
LOCK RELEASES.
Avd. Tres Cruces, 133
46017 Valencia
Spain
Contact: [email protected] / www.fermax.com/contact
For extended information, visit www.fermax.com