FURNITUREBOX FOSSANO User manual

FOSSANO
CHEST OF DRAWERS
ASSEMBLY GUIDE
www.furniturebox.co.uk
Scan QR code for more tips,
advice and assembly video or visit
furniturebox.co.uk/club/fossano-chest
SCAN ME

• Check you have all the components and
tools listed.
• Remove all ttings from the plastic bags
and separate them into their groups.
• We do not recommend the use of power
drills/drivers for inserting screws, as this
could damage the unit. Only use hand
screwdrivers and Allen keys.
• Keep children and animals away from the
work area, small parts could cause choking
if swallowed.
• Make sure you have enough space to
layout the parts before starting.
• Assemble the item as close to its nal
position (in the same room) as possible.
• Do not overtighten the nuts to avoid
causing damage to the threads.
Important - Please read these instructions fully before starting assembly
SAFETY AND
CARE ADVICE
!
NO POWER TOOLS
Follow us on Instagram
@furniturebox_uk
• Only clean using a damp
cloth and mild detergent,
do no use bleach or
abrasive cleaners.
• From time to time check
that there are no loose
screws on this unit
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre
SAFETY AND CARE ADVICE

www.furniturebox.co.uk
PLEASE CHECK CAREFULLY AND MAKE SURE YOU HAVE ALL
FITTINGS AND TOOLS LISTED BELOW BEFORE YOU START.
NOTE: The quantities above are the correct amount to complete the assembly. In
some cases more ttings may be supplied than are required.
IMPORTANT INFORMATION
TWO
PERSON
MAXIMUM
CAPACITY 50Kg
45 MINUTE
BUILD

Follow us on Instagram
@furniturebox_uk
STEP 2
Attach the footboards [1], [2], [3] and
[4] to Bottom Board [5] using Cam
Screws [A] and Cam Lock Nuts [B].
Flip over so that the 4 footboards sit
on the oor.
STEP 1
Put the pieces on a soft at surface e.g a
carpet to avoid any scratches or bumps.
Make sure you have all the components
and parts ready before you start.
First assemble the bottom of the unit.
Connect footboards [1], [2, [3] and [4]
together using Cam Screws [A]. Once
tightened, use the Cam Lock Nuts
[B] to lock in the pieces. Tighten with
screwdriver [G].
STEP 3
Connect the left side board [6] to the bottom
board [5] using wooden dowels [C], Cam Screws
[A] and Cam Lock Nuts [B]. Slide the lower
back board [7] into the grooves on the side and
bottom boards.
Then attach xing support board [8] using
wooden dowels [C], Cam Screws [A] and Cam
Lock Nuts [B].
Then insert the upper back board [9] into the
groove of side board [6] and xing board [8].

www.furniturebox.co.uk
STEP 4
Attach right side board [10] to the
unit, using Wooden Dowels [C], Cam
Screws [A] and Cam Lock Nuts [B].
FULL ASSEMBLY INSTRUCTIONS
STEP 5
Attach the top board [11] to the unit
using Wooden Dowels [C], Cam
Screws [A] and Cam Lock Nuts [B].
Step 7 provides detailed instructions
on how to attach the drawer sliders
[D] to the unit and to the drawer
sides.
STEP 6
Assemble your drawers. Connect
drawer side boards [12], [13] and [14]
together using Cam Screws [A] and
Cam Lock Nuts [B]. Slide drawer
bottom board [15] into the grooves in
the drawer sides. Attach drawer front
[16] to 3 of the drawers and drawer
front [17] for the bottom drawer. Use
Cam Screws [A] and Cam Lock Nuts
[B].

STEP 7
Drawer Sliders - part [D]
Each drawer slider comes as a pair - the “parent”
is the part that attaches to the inside of the unit.
and the “child” that attaches to the outside of the
drawer, on each side. To separate your drawer
sliders into “parent” [1} and “child” [2] parts, press
the black moving part and slide it.
Attach the “parent” sliders [1] to the unit side
boards in the locations show on the diagram
in Step 5, using screws [E] Make sure you install
the sliders facing the correct direction - end A1
towards the back of the unit and B1 at the front
of the unit. Make sure the B1 end is aligned with
the edge of the unit as per the diagram.
Attach the “child” sliders [2] to the sides of the
drawers using screws [E]. Make sure you attach
the “child” sliders facing the correct direction -
end A2 towards the back of the drawer and end
B2 towards the front of the drawer.
Attach drawer handles [15] to your drawers using
screws [F]. If your sliders are attached the correct
way round, the drawers will slide comfortably
into the runners on the unit.
ATTENTION: Be careful not to overload drawers.
STEP 8
Slide drawers into unit.
We strongly advise you use the
anti-tipping kit provided.

www.furniturebox.co.uk

The cushions (foam inserts and
covers) are not covered by the guarantee.