Grandview Cyber Series CB-MIxx User manual

Model CB-MIxx
GRANDVIEW REPRODUCING GENUINE COLORSGRANDVIEW REPRODUCING GENUINE COLORS
Thank you for purchasing a Grandview projection screen.
Before use, please read instructions carefully. After installation, store instructions for future reference.
Instruction Manual for
Cyber Series Intellectualized-Controlled Screen
GRANDVIEW REPRODUCING GENUINE COLORS
ISO9001:2000
International Certification
Grandview Crystal Screen Canada Ltd.
#11- 3751 North Fraser Way,
Marine Way Business Centre,
Burnaby, BC, Canada V5J 5G4
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.ca
Guangzhou Grandview Crystal Screen Co., Ltd.
P.O. 511400 Federal Ind. Zone No. 363, Yushan West Road,
Shiqiao, Panyu District, Guangzhou, Guangdong, China
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.com
www.grandviewscreen.com.cn

1
230V/120V/100V 50Hz/60Hz 90W/80W
Motorized Screen Power Specifications
Voltage Frequency Watts Application
Applies up to 120" motorized screens
Allen key (1pc)
Instruction manual (1pc)
Externnal IR Receiver (1 )pc
Alluninium casing
Screen fabric
Bottom rod
Description
Accessaries
Trigger line ( 1pc )
Fixing screw
Floating wall bracket (2pcs)
Floating wall bracket
5 40mm Tapping screw & cap (8sets)
M5x10 Screw (6pcs)
Ceiling hanger (2pcs)
Toppanel
Up buckle
Baffle
Down buckle

2
9Ignoring the safety warnings may
lead to injuries and/or damaging
the product.
Refrain from hanging anything on t he
screen as it may cause the scree n to
fall.
Do not connect any electrical
attachments or remote controls.
Fixtures should be installed in a secure
place to avoid accidents or the screen
falling.
Roll up the screen after every use.
Leaving it hanging for a long period
of time may cause the fabric to loosen.
Please contact your local dealer for
repair s or maintenance. Please contact
ourcompany if you have any further
questions. Avoid taking apart the
fixtures yourself. Loose parts may
cause the screen to fall.
Warnings
Do not take apart and replace with unknown parts. If there are any problems, please contact your local dealer.
Product specifications are subject to change.
The ceiling or wall used for fixture installation must be secure to prevent the screens from falling.
While installing electrical motors, please hire professionals or your local dealer to ensure safety. Amisconnection
may lead to fire or leaks.
Make sure the Fixing screw be fastened when using the wall bracket, to avoid any damage.
Keep all infrared wireless products away from fluorescent lighting as it may cause malfunctions.
Please read the following as any damage to the screen surface will affect the quality of the picture:
1.Avoid contact or touching the screen surface as it may cause scratches or tears.
2.Do not write or draw on the surface.
3.Clean the screen with a soft cloth and lukewarm water. Do not use any detergent or cleaning products.
Roll up the screen after every use. Ensure that the screen is level when installing; do not pull on the sides or fold
the screen.
To prevent unnecessary damage, the operating and maintenance of the screen should be done by adults.
Take out all the parts from the packaging and follow the accessagires guideline to ensure you have all parts.
There are three installation measures for this product, namely wall mounting, ceiling mounting and ceiling hang. The
installed distance can be changeable up to your needs via adjusting the slipper block, while the ideal position is the
mounting bracket is at its nearest point to the endcap, which can reduce unnecessary vibration or noise.
Installation
1. Choose screws for mounting according to wall material. ( Tips: Wood screws for wood wall, and Tapping screws
for concrete wall.)
2. Mount the brackets onto the wall, assuring they are at the horizontal level. (Tips: draw an erasable level line when
mounting the brackets) (Figure 1) Here below are the details:
Figure 1
Wood wall installation Wood ceiling installation Concrete wall installation Concrete ceiling installation
Figure 2 Figure 3 Figure 4 Figure 5
Floating wall bracket installation
Installation Steps
a) Wood wall and ceil ing installati on: Drill in the 5 x 40 screws through theappropriate holes in the bracket
( Figure 2-3 ).
b) Drywall and ceiling and installation:Install the anchors and drill inthe 5 x 40
( Figure 4-5).
screws into the appropriate
bracket holes.

38
Drop Limit
Retraction Limit
Up groove
Down groove
Figure 8 Figure 9
4. When mounting the screen onto Floating wall brackets, make sure the Up groove and the Down groove on the
housing match with the Up and the Down on the bracket seperately. ( Figure8-9 ).buckle buckle
5. Fasten the Fixing screw onthe bracket, to fix housing tightlyonto the brackets.( Figure 10-11 )
Figure 10 Figure 11
3. Loose theFixing screw to lower down the all the way. ( Figure6-7 )Baffle
Figure 6 Figure 7
Baffle
Fixing screw
Attention:
> Please make sure there isno dust or dirt on thefabric surface before rolling it back to the casing
> The recommened working time is less than 50 seconds. The motor will enter overheating protection
status and stop working for everycontinuous 4 minuters operation, user would need to wait for a
while until the motor cool downbefore operating again.
> There is no lube needed for the motor. Please be noticed that the appropriate setting is optimized
which requires no further adjustment, pleaseconsult the after sales team before adjusting the limits.

74
How to use External Control (Central Controller or RS232/USB):
1. Turn the manual/IR remote control switch to position "0" (remote control stalls)
2. Plug one side of the signal cord into the computer output jack at left side of the screen's end cap, the other side
of the singal cord to plug into the jack of Central Controller or computer RS232/USB
(Figure 24-25),
and then you can control up/pause/down of the screen via Central Controller or computer.
(Note: in order to use RS232
Control, an Adapter is necessary to be connected with, the Adapter is not in the accessory package)
How to use IR Remote Control
1. Turn the manual/IR remote control switch to position "0" (remote control stalls)
2. When there's nothing to keep our of the IR window, you can use the controller to control up/pause/down of the
screen (Figure 26).
3. For hidden installation or IR window is being kept out by something, please take out the IR Receiver Head and
plug it to the revelant hole, and then install it at the position where IR signal is available (Figure 27)
Inner IR Receiver
Window
External IR Jack
How to use Trigger
Trigger
(Figure 22-23)
" "
. Switch Manual/Remote Control Button to position "1" (manual stalls).
rigger control
Control:
1. Insert one end of the signal cable into the jack of the handle controller, and the other end into the
DC5V-12V output hole of the projector .
2. Press the control switch of the handle controller to the location.
3
4. When running the projector, the screen will spread the fabric automatic by synchronous; when closing the
projector, screen will be back automatic by synchronous too.
5. If you don't need to use the t , please draw off the burst line directly, then control it by your hand.
Figure 22 Figure 23
Figure 24 Figure 25
Figure 26 Figure 27
A
12
Ceiling hang installation
To choose the tapping screws with hanger or other screws with hanger (unprovided) according to ceiling material.
(Tips: Wood screws 5 x 40 for wook ceiling and tapping screws for concrete wall.)
1. To drill two same holes with an electric drill horizontally with wall, then fasten hangers(unprovided) onto the
ceiling. ( Figure 12 )
Figure 12
2. Use M5 x 10 screws in the accessory package to fix the ceiling hanger into wall bracket, make sure the
tightening screws on wall bracket are fixed tightly. ( Figure 13-14)
3. After fix the ceiling hanger, make sure the up groove and the down groove on the housing match with Up
and Down on the bracket separately and fasten the fixing screw on the bracket, to fix housing
tightly onto the brackets.( Figure 15-16)
buckle buckle
4. After finished step 2 and step 3, check whether wall bracket fix on the housing of screen tightly then you can
hang the screen according to the figure 17.
Figure 13 Figure 14
Figure 15 Figure 16
Figure 17

56
Connecting to the external power:
1. T
2. Switch on the power (within stated voltage).
ear off the glue cloth fixed on thebottom rod,ensure the bottom rod is not stuck bythe casing.
LAN
How to use Manual/Remote Control Switch Button: (Figure 18)
The screen has four kinds of optional control methods: IR Remote Control, Manual Control, Trigger Control, External
Control (Central Control or RS232/USB). When switching the Manual/Remote Control Switch Button to position "1",
you can use Manual Control or Trigger to control up/pause/down of the screen. When switching to position "0", you
can use IR Remote Control or External Control (Central Controller or Rs232/USB) to control up/pause/down of the
screen.
Manual/Remote Control
Switch Button
Trigger Jack
Central Controller
Manual Control
Connecting External IR
Projector
Computer Output
Jack
How to use manual switch control:
1. Switch Manual/Remote Control Button to position "1" (manual stalls).
2. " " ; it will come down slowly. When it is all the way down, it will
stop automatically (Figure 20) .
3. Turn the switch to " " to the screen; it will go up into the metal casing. When it is all the way up, it
will stop automatically (Figure 21).
4. To stop any time while the screen is in motion, turn the switch to 0.
Turn the switch to position to lower the screen
position lower
Figure 18
Figure 19 Figure 20 Figure 21
Manual
Control
Operation Instruction
How to install the battery:
1.Turn the controller around,push to open the cover as guide arrow.
2.Put the battery in accordingthe guide of cathode and anode.
3.Close the cover.
UP
DOWN
STOP
LED
remote controller
Controller button instruction
1.To raise screen press "UP .
2.To hold screen at desired position press STOP .
3.To lower screen press DOWN .
1.
2 will
3 will if
4
5
6
7
"
""
""
Caution:
The shortest distance between receiver and controller is 0.5 meter.
.Controller work within 30 degree away horizontally from t he cen ter of recei ver
point within 8 meters from the screen.
.The controller not work the signal was coveredby something.
.Keep the controller far away from high temperature and humid situation.
.Please change the battery when the signal is weak.
.Please take the battery out if the controller was not being used for long time.
.Please choose the same type battery as original supplied.
4. To raise the screen little at your desired position press MICRO-UP
5. To lower the screen little at your desired position press MICRO-DOWN
1GD IRan
MICRO-UP MICRO-DOWN
Instructions