Häfele W300-IMP User manual

NO. 2 POZI
DRILL BIT
Cabinet
Panels
included.
Hardware
included.
Required
Tools.
Handy
Tools.
Manufactured in New Zealand for: Mitre 10 New Zealand Limited.
Top Panel x1 Back Panel x1 Bottom Panel x1
Side Panels x2 Shelf Panel x1
SCREWS
POWER DRILL
CLAMP LEVEL TAPE
MEASURE
PENCIL LADDER
DOWELS
SHELF STUD HINGE
HINGE PLATE CONNECTOR SCREW A, B ( 2 )
5MM DRILL BIT HAMMER
Fixing Bottom and top Panels to Back Panel.
Inserting Dowels into Side Panels.
1.
2.
3.
WALL
CABINET
SINGLE SHELF
Assembly Instructions
Suitable for Wall Cabinets:
W300-IMP, W400-IMP,
W450-IMP, W600-IMP,
W800-IMP, W900-IMP.
732.25.819
Legend
A. = W300-IMP/
W400/W450-IMP
B. = W600-IMP/
W800/W900-IMP
• Line the bottom and top panels up by matching them to the holes on the back
 beforescrewxingthemwiththe50mmcabinetscrews.
A (16 ) B ( 18 ) 50mmCabinetscrew
A (2), B ( 4 )A,B(20)
A(4),B(5) A ( 2 ), B ( 4 )
Handy Note:Pleasereadtheinstructionscarefullybeforeyoustartandmakesuretoidentifythepartsyouneedforeachstep.
Whenassemblingitisbesttodoonasoftsurfacetopreventdamage.
A, ( 4 ), B, ( 8 ) 15mmScrew
• Whilethesidepanelsarelayingat,insertthedowelsintothe
 holesmarkedwitharrowsinthediagram.
• Laythesidepanelsatandxthehingemountsasshownbelow.
Note: W300-IMPtoW450-IMPwillonlyhavemountsononesidepanel.
Fixing the Mounting Plates.
Note:Connectorscrewsareusedto
connecttwocarcaseunitstogether.
5mmthroughholesareprovidedon
some of the front edges of the side
panelstoconnectadjacentcarcase.
SCREWDRIVER

4.
5.
6.
• Insertthesuppliedshelfstudstothecorrespondingholesonthesidepanelto
 achievethedesiredheight.
• Adjustableshelvessimplyrestontopofthestuds.
• Fixthehingesusing15mmScrewsasshown.
• Fixthedoorbuffersbyinsertingintothe5mmholesattopandbottom
 cornerofthedoor.
• Clipdoorsontothewallunit.Seehingeinstallationfordetails.
• Align the base, back and top panels onto the dowels on the side panel, as
 shownintheimage.
• Lift and align the second side panel to ensure dowels are aligned with
 thecorrespondingholes.Use50mmcabinetscrewstoxthetop,back 
 andbottompanelstothesidepanel.
• Flip the cabinet to secure the other side panel with back, top and base using
 50mmCabinetScrews.
Note: Door Front (and Optional door
buffers)soldseparately.
Shelf Placement.
Fixing the Hinges.
Hinge Installation & Adjustments.
• Hookthehingeintothefrontofthemount.
• Push the back down onto the hinge mount
untilyouhearaclick.
• Push this button to release the
 hingefromthemount.
• Usethesescrewstoadjustdoorup/down.
• Usethesescrewsto
 adjustdoorin/out.
• Usethesescrewstoadjustdoorright/left.
7.
Fixing Side Panels to Top, Back and Bottom.