Heatscope MHS-600 User manual

INT
Internaonal Version
ORIGINAL INSTALLATION
AND OPERATING INSTRUCTIONS
Electric radiant heater
for covered outdoor areas
Exclusively engineered and made in Germany.

Contents
1. Usage
2. Safety instrucons
3. Unpacking / packing
4. Installaon instrucons
5. Operaon
6. Installaon instrucons & minimum clearances
7. Dimensions
8. Cleaning / maintenance
9. Error status detecon
10. Technical data
11. Conformity declaraon
12. Guarantee & warranty
13. Replacement parts
14. Decommissioning / disposal
This installaon and operaon manual covers the following products:
MHS-600 MHS-1800 MHS-2400 MHS-3200
MHS-WH45 MHS-WHSL MHS-MH MHS-DAH 6/30/50
MHS-GMS MHS-DAHDOP MHS-DAHV50/30 MHS-DAHDB
MHS-WS 5/10/15/20 MHS-ASK
Please also refer to the instrucon manuals for oponal accessories (see 4.5).

1. Usage
Thank you for choosing to purchase the electric radiant heater HEATSCOPE™.
You have purchased one of the most advanced heang systems for indoor and covered outdoor areas.
The so-called dark radiator (infrared radiant heater without red light) is characterized by a focused
distribuon of heat, which transports the heat to where it is needed. Once the heater has been properly
ed, there is no energy wasted on unused space. The following instrucons should assist in this regard.
The new HEATSCOPE™ is a high-intensity radiant heater, which was designed for covered indoor or
covered outdoor use in a private or commercial environment and may not be used for other purposes. It
can be used on terraces and in pavilions as well as in smoking areas, winter gardens or wellness areas on
cooler days to generate a comfortable body heat without substanally heang the enre environment.
The radiant heater allows the radiant heat to be transported up to a distance of about 3 meters. The unit
can be aligned in a targeted way to a parcular area using various brackets.
1. Please read the instrucons carefully prior to installaon. The operang instrucons should be
regarded as part of the product. You should only install the unit when you have read and understood the
operang instrucons. If in doubt, contact the vendor or manufacturer.
2. Keep the instrucons for future reference throughout the lifecycle of the product. Make sure to pass
on the operang instrucons to any subsequent owner of the unit and ensure that any supplements
received are included with the instrucons.
3. Before starng the installaon, you must ensure that the operang voltage corresponds to that stated
on the nameplate of the HEATSCOPE™ or accessories.
4. These operang instrucons are intended solely for the series products menoned above. Deviaons
in relaon to technical data, installaon and dimensions are possible in the case of special versions.

2. Safety instrucons
The usual local building and re safety regulaons must be observed.
WARNING: This unit is not equipped with a device to control the room temperature. The heater must
not be used in small spaces that are inhabited by people who cannot independently leave the room,
unless constant supervision is ensured.
1. The HEATSCOPE™ must be ed with an all-pole ON/OFF switch (not included in scope of delivery).
You can likewise operate the radiant heater using a radio receiver and a remote control, which are availa-
ble as oponal accessories. Connecon to a residual current circuit breaker and fuse is necessary.
2. The device is equipped with reversible overheang protecon. If the overheang protecon is trigge-
red, it automacally powers on the device again aer a certain cooling me.
3. The unit may only be operated in principle with an approved disconnecng device. The heater is
equipped as standard for electrical connecon with a separate open cable without a plug. A connecon
cable with safety plug (Schuko) is sold separately as an accessory.
4. The unit must be securely mounted and connected to the main power supply by a qualied electrician
in accordance with the applicable standards and regulaons for electrical wiring in the electrical trade in
the respecve country of installaon.
5. The heater may not be placed immediately below a socket outlet. A safety clearance of at least 10cm
to the next power source must be guaranteed from the long sides.
6. Under VDE 0100, Part 701, the radiant heater may only be installed in area 3 in installaon rooms with
high humidity (bath, spa, pool, etc.). If the HEATSCOPE™ is installed in such an environment with high
humidity, the switches or other operang units must be installed such that they cannot be touched by
persons who are in direct contact with water.
7. Once the device is connected to a power source or powered by an „ON“ switch or other operang
opon, it takes about 10 minutes for the radiant heater to reach the opmum operang temperature.
8. The front side of the heater can reach a temperature of up to 700°F / 380°C under ideal condions,
depending on the room situaon and environmental condions. Do not touch any part of the heater
during operaon and up to 60 minutes aer it has been switched o.
9. Use cauon when operang the unit. This unit is not intended for use by persons (including children)
with reduced physical, sensory or mental abilies or lack of experience and/or knowledge, unless they
are supervised by a person responsible for their safety or have received instrucon from them on how to
operate/use the device.
10. Make sure that no cables or furniture, ammable materials or other items come in contact with the
surface of the radiant heater and never cover the unit. The unit must not be covered with insulang
materials or similar materials under any circumstances.
11. The unit must never be operated unaended. Children should always be supervised to ensure that
they do not play with the device.
12. If the mains cable for this unit is damaged, it must be replaced by the manufacturer or the
manufacturer‘s customer service department to avoid hazards.

13. If the unit or accessories have defects, cracks, fractures or other damage, they may no longer be
operated and must be disconnected properly from the electrical cable/power supply for repair purposes,
sent back to the manufacturer or disposed of. The unit must be idened accordingly to prevent recon-
necon.
14. Note that depending on the currently available supply voltage the actual power of the device may
change as well as the emied power as a result of environmental inuences.
15. Make absolutely sure to always switch o the device aer use.
3. Unpacking / packing
Carefully unpack the unit and the accessories, do not use sharp objects that could damage the unit to
open the packaging.
This product was packaged in an eco-friendly way. All HEATSCOPE™ packaging coming into circulaon
either directly or via trade is cered according to §6 of the packaging regulaons. All HEATSCOPE™
packaging can therefore be disposed of in an environmentally friendly manner in collecon containers
for packaging materials. The respecve local regulaons must be observed in this respect. Further infor-
maon is available upon request.
4. Installaon instrucons
The dierent opons for installing the HEATSCOPE™ are shown in the diagrams on the following pages in
Secon 4.
Make sure that the radiant heater is securely connected and xed to the installaon surface. The fas-
teners must be of a tensile and shear strength of at least 3 mes the weight of the radiant heater that
is being mounted including the accessories. Use the corresponding screws and plugs (not supplied) to
secure the unit.
The HEATSCOPE™ must never be mounted vercally under any circumstances.
The following list is an extract from the available standard accessories and aachments. As special
versions are also available, the appropriate installaon and operang instrucons should be requested if
necessary from the seller or manufacturer.
For simplicity, only one mounng bracket is shown in the installaon descripon. Please note that you
always need two mounng brackets to mount your device safely. Always make sure that both mounng
brackets are ed exactly in series one aer the other and that the securing clips are oppositely aligned
to each other and are facing outward. Please refer to the minimum mounng dimensions of the unit in
Secon 7 Dimensions.
For addional informaon and installaon opons, refer also to www.HEATSCOPE.com

4.1 HEATSCOPE™ MHS-MH
· Diagram (5) shows the HEATSCOPE™ together with the pre-assembled mounng bracket MHS-MH.
· Fit the mounng bracket MHS-MH (1) on/to the intended installaon surface. (Please note the mini-
mum clearance for installaon surfaces in Secon 6.)
· Repeat this step (1) with the second mounng bracket. Make sure that both mounng brackets are
mounted exactly in series one aer the other and that the securing clips (3) are oppositely aligned to
each other and are facing outward.
· Now slide the HEATSCOPE™ (2) onto the mounng brackets unl the clip (3) clicks audibly into place on
both sides above the raised side plate (4) and the HEATSCOPE™ is secured from slipping out.
1
2
3
4
5
Mounng bracket drilling dimensions
Figure: (1) Mounng bracket MHS-MH; (2) HEATSCOPE™ radiant heater; (3)
Securing clip on mounng bracket; (4) Raised side plate; (5) HEATSCOPE™ incl.
mounng bracket MHS-MH
Scope of delivery
2 x wall brackets
4 x screws M6
(including washers)
4 x nuts M6

4.2.1 HEATSCOPE™ MHS-WH 45
· Diagram (6) shows the HEATSCOPE™ together with the 45° wall bracket MHS-WH 45.
· Fit the mounng bracket (1) using the supplied screws, washers and nuts on the wall bracket (2). Now
secure the assembled wall bracket on/to the designated installaon surface. (Please note the minimum
clearance for installaon surfaces in Secon 6.)
· Repeat these steps (1 and 2) with the second wall bracket MHS-WH45. Make sure that both mounng
brackets (1) are mounted exactly in series one aer the other and that the securing clips (3) are opposi-
tely aligned to each other and are facing outward.
· Now slide the HEATSCOPE™ (5) onto the mounng brackets unl the clip (4) clicks audibly into place on
both sides above the raised side plate (4) and the HEATSCOPE™ is secured from slipping out.
Drilling dimensions
Scope of delivery
2 x wall brackets
4 x screws M6
(including washers)
4 x nuts M6
1
2
4
5
3
6
Figure: (1) Mounng bracket MHS-MH; (2) 45° wall bracket MHS-WH 45;
(3) Securing clip on mounng bracket; (4) Raised side plate; (5) HEATSCOPE™
radiant heater; (6) HEATSCOPE™ incl. wall bracket MHS-WH 45
3

Drilling dimensions
Scope of delivery
2 x wall brackets
2 x rotary elements
2 x mounng
brackets
(already fully pre-
assembled)
1
2
4
53
6
Figure: (1) Mounng bracket MHS-MH; (2) Adjustable wall bracket MHS-WHSL;
(3) HEATSCOPE™ radiant heater; (4) Securing clip on mounng bracket; (5) Raised
side plate; (6) HEATSCOPE™ incl. adjustable wall bracket MHS-WHSL
4.2.2 HEATSCOPE™ MHS-WHSL
· Diagram (6) shows the HEATSCOPE™ together with the adjustable wall bracket MHS-WHSL.
· Fit the pre-assembled adjustable wall bracket MHS-WHSL (1) on/to the intended installaon surface.
(Please note the minimum clearance for installaon surfaces in Secon 6.)
· The scope of delivery includes two dierent adjustable mounng brackets MHS-WHSL with dierent
orientaon for mounng on the le or right side. The securing clips of the mounng bracket must
always be oppositely aligned to each other and face outward (4).
· Remove the two screws (2) slightly (do not loosen the nuts!) and adjust the mounng bracket to exactly
the right angle. Then ghten the screws (2) again.
· Repeat these steps (1 and 2) with the second wall bracket MHS-WHSL. Make sure that both mounng
brackets (1) are mounted exactly in series one aer the other and that the securing clips are facing
outward.
· Now slide the HEATSCOPE™ (3) onto the mounng brackets unl the clip (4) clicks audibly into place on
both sides above the raised side plate (5) and the HEATSCOPE™ is secured from slipping out.

Scope of delivery
4 x threaded ele-
ments
2 x spacers
2 x extension tubes
300mm
4 x screws M6 (incl.
washers)
4.3.2 HEATSCOPE™ MHS-DAH 300 / MHS-DAH 500
· Diagram (10) shows the HEATSCOPE™ with the 19,68 inch / 500mm ceiling suspension MHS-DAH 500
(installaon instrucons apply correspondingly for the 11,81 inch / 300mm spacer MHS-DAH 300).
· Fit the rst threaded element (6) on/to the intended installaon surface. For easy mounng, these
threaded elements can be supplemented by oval ceiling aachments MHS-DAHDB that are oponally
available as accessories. (Please note the minimum clearance for installaon surfaces in Secon 6.)
· Fit the second threaded element
(2) using one of the supplied
screws and washers – in the
following sequence: screw, washer,
mounng bracket, threaded
element - on the mounng bracket
MHS-MH (1). Now assemble in
the following sequence: mounng
bracket, threaded element, spacer,
extension tube, spacer with the
rst threaded element (1, 2, 3, 4, 5
to 6) on the installaon surface.
· Repeat these steps (1 to 6) with
the second spacer MHS-DAH 50.
Make sure that both mounng
brackets (1) are mounted exactly in
series one aer the other and that
the securing clips are oppositely
aligned to each other and are
facing outward.
· Now slide the HEATSCOPE™ (7)
onto the mounng brackets unl
the clip (8) clicks audibly into place
on both sides above the raised side
plate (9) and the HEATSCOPE™ is
secured from slipping out.
1
2
4
5
3
6
8
7
9
10
Figure: (1) Mounng bracket MHS-MH; (2) Threaded element; (3) Spacer; (4)
Extension tube; (5) Spacer; (6) Threaded element; (7) HEATSCOPE™; (8) Securing
clip on mounng bracket; (9) Raised side plate; (10) HEATSCOPE™ incl. ceiling
suspension MHS-DAH 500

4.3.3 HEATSCOPE™ MHS-DAHV 300/ MHS-DAHV 500
· Diagram (9) shows the HEATSCOPE™ together with the 11,81 inch / 300mm ceiling suspension MHS-
DAH 300 plus addional 11,81 inch extension MHS-DAHV 300 (the installaon instrucons apply corres-
pondingly to the 19,68 Inch / 500mm extension MHS-DAHV 500).
· Fit the rst threaded element (5) on/to the intended installaon surface. For easy mounng, these
threaded elements can be supplemented by oval ceiling aachments MHS-DAHDB that are oponally
available as accessories. (Please note the minimum clearance for installaon surfaces in Secon 6.)
· Now install the module MHS-DAH as per 4.3.2 in these operang instrucons (1) without screwing the
whole assembly to the threaded ele-
ment on the designated installaon
surface.
· Screw the spacer and the extension
tube MHS-DAHV 30 to the ceiling
suspension MHS-DAH 300 from 4.3.2
(1, 2, 3). Now assemble in the following
sequence: mounng bracket, threaded
element, spacer, extension tube,
spacer, extension tube, spacer with the
rst threaded element (1, 2, 3, 4, to 5)
on the installaon surface. Never use
more than two spacer tubes!
· Repeat these steps (1 to 5) with the
second spacer MHS-DAHV. Make sure
that both mounng brackets (1) are
mounted exactly in series one aer
the other and that the securing clips
are oppositely aligned to each other
and are facing outward.
· Now slide the HEATSCOPE™ (7) onto
the mounng brackets unl the clip
(8) clicks audibly into place on both
sides above the raised side plate (6)
and the HEATSCOPE™ is secured from
slipping out.
Scope of delivery
2 x extension tubes
2 x spacers
1
2
4
5
3
6
7
9
8
Figure: (1) Mounng bracket MHS-DAH 30 (see 4.3.2); (2) Spacer; (3) Extension
tube; (4) Spacer; (5) Threaded element; (6) Raised side plate; (7) HEATSCOPE™;
(8) Securing clip on mounng bracket; (9) HEATSCOPE™ incl. ceiling extension
MHS-DAHV 300

4.3.4 HEATSCOPE™ MHS-DAGSL
· Diagram (10) shows the HEATSCOPE™ with the 11,81 inch / 300 cm ceiling suspension MHS-DAH 300
plus addional ceiling mount hinge joint MHS-DAGSL with freely adjustable angle (installaon instruc-
ons apply correspondingly for the 19,69 inch / 500 cm extension MHS-DAHV 50 plus addional ceiling
mount hinge joint MHS-DAHGMS with freely adjustable angle).
· Fit the rst threaded element (6) on/to the intended installaon surface. For easy mounng, these
threaded elements can be supplemented by oval ceiling aachments MHS-DAHDB that are oponally
available as accessories. (Please note the minimum clearance for installaon surfaces in Secon 6.)
· Fit the second threaded element (2) using one of the supplied screws and washers – in the following
sequence: screw, washer, mounng bracket, threaded element - on the mounng bracket MHS-MH (1
to 2).
· Now screw down the freely adjustable ceiling mount hinge joint MHS-DAGSL to the second threaded
element on the mounng bracket (2 to 3).
· Now connect the extension tube with the angle-adjustable joint MHS-DAGSL. Assemble in the following
sequence: mounng bracket, threaded element, angle-adjustable joint, extension tube, spacer with the
rst threaded element (1, 2, 3, 4, 5 to 6) on the installaon surface. Never use more than one spacer
tube plus an adjustable joint!
· Repeat these steps (1 to 6) with the second freely adjustable hinge joint MHS-DAHGMS. Make sure that
both mounng brackets (1) are mounted exactly in series one aer the other and that the securing clips
are oppositely aligned to each other and are facing outward.
· To set the adjustable ceiling mount hinge joint to the desired angle, slightly loosen the screw at the hin-
ge joint and align the mounng bracket accordingly. Make sure that both mounng brackets are aligned
at exactly the same angle so that the HEATSCOPE™ radiant heater can be pushed smoothly into place.
· Now slide the HEATSCOPE™ (7) onto the mounng brackets unl the clip (8) clicks audibly into place on
both sides above the raised side plate (6) and the HEATSCOPE™ is secured from slipping out.

Scope of delivery
2 x ceiling mount
hinge joints with
freely adjustable
angle
2
4
5
3
6
7
9
8
1
10
Figure: (1) Mounng bracket MHS-MH; (2) Threaded element; (3) Angle-adjustable
ceiling mount hinge joint MHS-DAHGSM; (4) Extension tube; (5) Spacer; (6) Threa-
ded element; (7) HEATSCOPE™; (8) Raised side plate; (9) Securing clip on mounng
bracket; (10) HEATSCOPE™ incl. angle-adjustable ceiling joint MHS-DAGSL

4.4 HEATSCOPE™ ceiling suspension 2 x 45° MHS-DAHDOP
· The image shows two HEATSCOPE™ radiant heaters with the 11,81 Inch / 300mm ceiling suspension
MHS-DAH 300 plus addional 45° dual ceiling suspension (xing bracket) MHS-DAHDOP.
· Fit the oval ceiling aachment MHS-DAHDB, which comes as an accessory, on/to the intended installa-
on surface. (Please note the minimum clearance for installaon surfaces in Secon 6.)
· Fit two mounng brackets MHS-MH for each 45° dual xing bracket MHS-DAHDOP using one of the
supplied screws and washers – in the following sequence: screw, washer, mounng bracket, dual xing
bracket. Make sure that the securing clips on the mounng brackets are oppositely aligned to each
other and are facing outward.
· Now connect the ceiling suspension MHS-DAH with the dual xing brackets MHS-DAHDOP and the
oval ceiling aachment MHS-DAHDB as follows: Screw the threaded element to the dual xing bracket
using the screw supplied. Then secure the extension tube to the threaded element with the dual ceiling
suspension. Screw the whole assembly into the oval ceiling aachment, which you already ed on/to
the designated installaon surface.
· Repeat these steps with the second dual mounng bracket MHS-DAHDOP. Make sure that both
mounng bracket pairs are mounted exactly in series one aer the other and that the securing clips are
oppositely aligned to each other and are facing outward.
· Finally slide the two HEATSCOPE™ radiant heaters onto the mounng brackets unl the clip clicks
audibly into place on both sides above the raised side plate and the HEATSCOPE™ heaters are secured
from slipping out.
Scope of delivery
2 x 45° dual xing
brackets
4 x screws M6
(incl. Washers)

4.5 HEATSCOPE™ installaon devices and accessories (available oponally)
Please refer to the separately available instrucon manuals.
Radio receiver module
MHS-FBM US
MHS-FBM US2
Hand-held remote control
MHS-FBHS
Connecng element
MHS-ESM US
MHS-ESM US
* The HEATSCOPE™ ¤ radiant heater is normally delivered with an open cable without a plug. The
connecon and the relevant tests required for staonary units must be performed and documented by a
qualied electrician. Note here, in any case, the appropriate standards, e.g. VDE etc.
The connecon cable MHS-ASK with safety plug (with silicone cable and cable connectors, black with
locking pin, 16 A/250 V AC AWG15, length approx. 59 Inch 1,5m) is available as an accessory - exclusively
for the European market.
Wall-mounted remote control
MHS-FBWS
Oval aachment for
DAH MHS-DAHDB

5 . Operaon
The unit can be operated following successful installaon/assembly.
The HEATSCOPE™ has an LED that is integrated into the cover plate between the heang prole and the
upper tray. Once the HEATSCOPE™ is supplied with power, this LED lights, indicang that the device is
operang.
It may happen in conjuncon with accessories that this LED does not light although the accessory is
supplied with voltage/current. Note here in any case the operang instrucons supplied with each
accessory.
Although there is power to the HEATSCOPE™, it is possible that the LED likewise does not light if the
temperature protecon was acvated.
Do not forget to switch o your HEATSCOPE™ again!
6. Installaon instrucons and minimum clearances
The following installaon conguraon ensures that the HEATSCOPE™ radiant heater is working eec-
vely. All the minimum clearances that must be met regardless of the installaon environment are listed.
1. The HEATSCOPE™ must be ed with an all-pole ON/OFF switch (not supplied).
2. Depending on the installaon conguraon, the HEATSCOPE™ can reach a surface temperature of
up to 700°F / 380°C under opmum condions. Wind, humidity, ambient temperature as well as the
installaon conguraon itself can inuence the surface temperature signicantly.
3. Fit the unit if possible so that it is well protected from wind and weather. The surface of the unit cools
down signicantly as a result of wind, which aects the perceived body temperature decisively.
4. Fit the unit in covered interior or exterior areas only.
5. The HEATSCOPE™ must never be mounted vercally under any circumstances.
6. The radiant heater must have a minimum lateral clearance of 12 inch / 30 cm to each adjacent wall,
at least 31,5 inch / 80 cm to each surface on the front and at least 3 inch / 6 cm to the rear mounng
surface. Other relevant protecon measures may have to be met here in accordance with local re
safety regulaons.
7. The heater must not be located immediately below a socket outlet and must also have at least a mini-
mum lateral clearance of 3,94 inch / 10 cm to all socket outlets.
8. All cables must be routed so that they cannot come into contact with the radiant heater at any me.
9. Recommended operang temperature: To operate your heater eecvely and for the purpose of
saving energy in general, make sure to only turn it on at an ambient temperature of between 50°F /
10°C and 68°F / 20°C.

10. Please note the following diagram. The diagrams show the ceiling and wall mounng of the HEAT-
SCOPE™ including all minimum clearances to be observed. The prescribed minimum mounng height
of the HEATSCOPE™ radiant heater is 82,7 inch / 210 cm.
11. The assembled units must have a clearance of at least 59 inch / 150 cm to each other on the longer
side. If the devices are mounted with the heang surfaces aligned to each other, they must have a
clearance of at least 118 inch / 300 cm.
A > 12 inch/30cm to the wall
> 3 inch/6 cm to another HEATSCOPE™
B > 12 inch/30 cm to the wall
> 60 inch/150 cm to another HEATSCOPE™
C > 3 inch/6 cm
D > 12 inch/30 cm to the wall
> 3 inch/6 cm to another HEATSCOPE™
E > 83 inch/210 cm
F > 32 inch/80 cm
G > 8 inch/20 cm
H > 5 inch/12 cm
I > 83 inch/210 cm
J > 3 inch/6 cm
K > 12 inch/30cm to the wall
> 59 inch/150 cm to another HEATSCOPE™
L > 83 inch / 210 cm
Minimum clearances
The dimensions given are minimum values and may dier from the local building and re regulaons.
The laer must be observed and complied with in any case.
The illustrated installaon surfaces must comply at least with re protecon class A2.
Please note: The HEATSCOPE™ fullls IP protecon class 4 (IP-X4) for ceiling mounng and IP protecon
class 0 (IP-X0) for wall mounng.
Protect from moisture
and humidity.
Do not
use force.
Protect from
wind and dras.

7. Dimensions
Type/Maße A B C DE
MHS-600 US 593 mm/245,3 inch 108 mm/4,26 inch 169 mm/6,66 inch 61,5 mm/2,42 inch 200 mm/7,88 inch
MHS-600 US2 593 mm/245,3 inch 108 mm/4,26 inch 169 mm/6,66 inch 61,5 mm/2,42 inch 200 mm/7,88 inch
MHS-1600 US
993 mm/402,76 inch 108 mm/4,26 inch 169 mm/6,66 inch 61,5 mm/2,42 inch 200 mm/7,88 inch
MHS-1800 US2
993 mm/402,76 inch 108 mm/4,26 inch 169 mm/6,66 inch 61,5 mm/2,42 inch 200 mm/7,88 inch
MHS-2400 US2
1493 mm/599,61 inch 108 mm/4,26 inch 169 mm/6,66 inch 61,5 mm/2,42 inch 200 mm/7,88 inch
MHS-3200 US2
1993 mm/796,46 inch 108 mm/4,26 inch 169 mm/6,66 inch 61,5 mm/2,42 inch 200 mm/7,88 inch
All dimensions are approximate values in mm and inch.
Heang surface
Rear side/installaon side
Electrical
connecon
A HEATSCOPE™ MHS length
BAachment length
CHEATSCOPE™ width
D HEATSCOPE™ height
EMinimum clearance of
mounng brackets from
Secons 4.1 to 4.5
Screw M6x8
plus washer
Screw M6x8
plus washer

8. Cleaning and maintenance
It is important that the HEATSCOPE™ is cleaned regularly when installed in outdoor locaons, in order to
ensure a long and ecient operang life.
The aluminum construcon of the HEATSCOPE™ together with the anodized surface helps to preserve
the heater even in coastal locaons.
In order to ensure opmum thermal performance, the surfaces of the heater must be cleaned regularly
with a damp cloth. It is parcularly important in this regard that the heater is not turned on and has
been turned o at least 60 minutes before cleaning. Otherwise, there is increased risk of injury and
burns!
Always make sure that no voltage/current is applied to the HEATSCOPE™, the controller or the aach-
ment during cleaning and that the devices are unplugged and protected against being restarted while
cleaning.
Cauon!
Do not use a high pressure hose or other such high pressure water equipment to clean the HEATSCOPE™.
Also, do not use sharp objects and aggressive cleaning agents. Make sure that no cleaning residue
remains on the unit.
9. Error status detecon
Error descripon Cause Soluon
The HEATSCOPE™ does not heat
up.
- Voltage is incorrect.
- No voltage.
- The unit is defecve.
- Check the supply voltage.
- Send the unit in if necessary.
The HEATSCOPE™ smells like it is
burning.
- Transport lock is sll on the
heang prole.
- The unit is defecve.
- Remove the transport lock.
- Send the unit in if necessary.
The LED on the HEATSCOPE™ is
not lighng although the unit is
switched on.
- Temperature protecon has
acvated.
- The unit is defecve.
- Unplug the unit and allow to
cool.
- Send the unit in if necessary.
The HEATSCOPE™ triggers the
residual current circuit breaker
or fuse.
- The unit was wet.
- The unit is defecve.
- Do not start up the unit again.
- Send the unit in if necessary.
The HEATSCOPE™ is not warm
enough.
- Incorrect or inappropriate
installaon conguraon.
- Ambient temperatures too low.
- Environmental inuences,
temperature, wind, snow.
- Check installaon
conguraon.

10. Technical data
Operang voltage 220-240V / 50 Hz
Temperature of
heang surface
Up to 700°F / 380°C
Temperature of
housing
Up to 194°F / 90°C
Heang me approx. 10 min.
Protecon class IP X4 for ceiling-mounted
IP-X0 for wall-mounted
Operang ambient
temperatures
23°F to +73,4°F / -5°C to + 23°C
70% RH non-condensing
Storage temperature 4°F to +149°F / -20°C to +65 °C
Connecon 3 x AWG14 open plug-in cable without plug, resistant to 221°F / 105°C,
59 inch / 1,5 m length
or 3 x AWG15 plug-in cable with safety plug, heat resistant to 338°F /
170°C, 59 inch / 1,5 m length (oponally available as accessory)
or aachments (oponally available as accessories)
MHS-600 MHS-1800
output power: 220-240V / 600W output power: 220-240V / 1600W
dimensions: 2,42 x 6,65 x 23,35 inch
61,5 x 169 x 593mm
dimensions: 2,42 x 6,65 x 39,09 inch
61,5 x 169 x 993mm
weight: 6,61 lbs / 3 kg weight: 11,02 lbs / 5 kg
MHS 2400 MHS 3200
output power: 220-240V / 2400W output power: 220-240V / 3200W
dimensions: 2,42 x 6,65 x 58,78 inch
61,5 x 169 x 1493mm
dimensions: 2,42 x 6,65 x 78,46 inch
61,5 x 169 x 1993mm
weight: 17,64 lbs / 8 kg weight: 23,1lbs / 11 kg
Please also read the operang instrucons for the accessory items for the devices. The current building, re safety and
emission regulaons must always be observed. Right of technical modicaons reserved in the interest of progress.