HunterDouglas PowerView Parts list manual

Installation • Operation • Care
Horizontal Blinds
PowerView
®
Motorization and
SimpleLift
™
with PowerView Motorization
Operating Systems

CONTENTS
GETTING STARTED
Product View — PowerView®Motorization ....................................................................1
Product View — SimpleLift™with PowerView Motorization...........................................2
Tools and Fasteners Needed ............................................................................................3
Unpack the Blind...............................................................................................................3
INSTALLATION
Installation Overview .......................................................................................................4
STEP 1 — Install the Brackets .........................................................................................4
Mount the Installation Brackets — Inside or Ceiling Mount .....................................5
Mount the Installation Brackets — Outside Mount ...................................................7
STEP 2 — Connect the Power Cable..............................................................................10
STEP 3 — Install the Blind.............................................................................................11
STEP 4 — Connect the Power Source, If Applicable.....................................................15
OPERATION
Testing the Blind.............................................................................................................18
Using the PowerView Remote........................................................................................18
Resetting the Blind (If Necessary)..................................................................................20
Complete the Installation ...............................................................................................20
Operate the Blind............................................................................................................23
Troubleshooting ..............................................................................................................24
CARE
Removing the Blind (If Necessary) .................................................................................28
Cleaning Procedures.......................................................................................................28
CHILD SAFETY
Cord Connector ...............................................................................................................29
Reassembly of Cord Connector ......................................................................................29
Cord Cleats......................................................................................................................30
DECLARATIONS ............................................................................................................31
WARRANTY......................................................................................................Back Cover
Questions?
Call Hunter Douglas Consumer Support at 1-888-501-8364.
© 2018 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or
their respective owners.

GETTING STARTED
1
Product View — PowerView®Motorization
End
Bracket
Hold-Down
Brackets and Pin
(Optional)
1
Required with 2
1
∕ 2 " slat size; optional with 1
3
∕ 8 " and 2" slat sizes.
2
Valance, valance clips, slats, bottom rail, and tassel vary by product.
Intermediate
Bracket
(If Required)
Valance Splice
(If Required)
Valance 2
Corner Clips for
V
alance Returns
(If Required)
End Bracket
Spacer Block1
Intermediate
Bracket
Spacer Block1
Bracket
Shim
(Optional)
2" or 4"
Extension
Brackets
(Optional)
End Bracket
Spacer Block1
End
Bracket
Power
Cable
Universal
Valance Clips 2
Pebble®
Remote
Surface
Remote
12V Battery
Wand
Magnetic
Valance Clips 2
Transceiver
Assembly
Programming
Button

2
GETTING STARTED
Product View — SimpleLift™with PowerView®Motorization
End
Bracket
1
Required with 2
1
∕ 2 " slat size; optional with 1
3
∕ 8 " and 2" slat sizes.
2
Valance, valance clips, and slats vary by product.
Intermediate
Bracket
(If Required)
Valance Splice
(If Required)
Valance 2
Corner Clips for
V
alance Returns
(If Required)
End Bracket
Spacer Block1
Intermediate
Bracket
Spacer Block1
Bracket
Shim
(Optional)
2" or 4"
Extension
Brackets
(Optional)
End Bracket
Spacer Block1
End
Bracket
Power
Cable
Universal
Valance Clips 2
Pebble®
Remote
Surface
Remote
12V Battery
Wand
Magnetic
Valance Clips 2
Transceiver
Assembly
Programming
Button
SimpleLift™
Hold-Down
Brackets
(Optional)

GETTING STARTED
3
Thank you for purchasing Hunter Douglas horizontal blinds. With proper installation,
operation, and care, your new blinds will provide years of beauty and performance.
Please thoroughly review this instruction booklet and the enclosed packing list before
beginning the installation.
Tools and Fasteners Needed
 Ballpoint pen
 Flat blade and Phillips screwdrivers
 Level (laser level is recommended)
 Measuring tape and pencil
 Power drill,
3
⁄ 32 " drill bits, and
1
⁄ 4 " hex driver (or socket wrench with
1
⁄ 4 " hex socket)
In addition, you will need fasteners designed to work with your specific mounting surface(s).
 #6 Hex Head Screws (Provided). Two 1
1
⁄ 2 " screws are provided per installation bracket.
 Longer #6 Hex Head Screws (Not Provided). If using spacer blocks, use #6 screws
long enough for a secure attachment.
 Speed Nuts and Screws (Provided). Extension brackets come with screws and
speed nuts.
Unpack the Blind
 Remove the blind from the package. Keep the packaging
until the blind operates to your satisfaction.
 Refer to the packing list and check for all necessary parts.
 Contents of your hardware package may vary
depending upon the options chosen.
 Do not remove the slat protector tape (if applied).
Doing so will damage the slat finish.
Speed Nut
and Screw
(Two Provided with
Each Extension Bracket)
#6 x 1
1
∕ 2 "
Hex Head Screw
(Provided)
Longer #6 Hex Head Screw
for Use with Spacer Blocks
(Not Provided)
16
Do Not
Remove
Slat Protector
Tape

INSTALLATION
4
Installation Overview
To install your blind, you will need to perform the following three steps:
STEP 1: Install the Brackets
STEP 2: Connect the Power Cable
STEP 3: Install the Blind
STEP 4: Connect the Power Source, If Applicable
STEP 1 — Install the Brackets
 Two end brackets are used to mount horizontal blinds. Wider blinds also require one or
two intermediate brackets, as shown in the tables below.
PowerView Motorization Operating System
SimpleLift™with PowerView Motorization Operating System
Mounting Types and Window Terminology
If the installation brackets are mounted correctly, the rest of the installation process follows
easily. To prepare for this important first step, review the mounting types and basic window
terminology illustrated below.
 Refer to the appropriate page below based on your order:
 Inside or Ceiling Mount — Page 5
 Outside Mount — Page 7
Width of Blind Intermediate Brackets
Up to 48" 0
48
1
⁄ 8 " – 60" 1
60
1
⁄ 8 " – 96" 2
Width of Blind Intermediate Brackets
Up to 48" 0
48
1
⁄ 8 " – 96" 1
96
1
⁄ 8 " – 144" 2
2" Aluminum Blinds
1
3
⁄ 8 ", 2", and 2
1
⁄ 2 "Wood Blinds
2" and 2
1
⁄ 2 " Alternative Wood Blinds
Outside Mount
Blind mounts
outside window
opening.
Inside Mount
Blind fits within
window opening.
Collectively, the sill and
jambs are called the
“window casement.”
Molding
Head Jamb
Sill
Jamb Jamb
Width of Blind Intermediate Brackets
Up to 48" 0
48
1
⁄ 8 " – 60" 1
60
1
⁄ 8 " – 96" 2
Width of Blind Intermediate Brackets
Up to 48" 0
48
1
⁄ 8 " – 96" 1
96
1
⁄ 8 " – 120" 2
2" Aluminum Blinds
1
3
⁄ 8 ", 2", and 2
1
⁄ 2 "Wood Blinds
2" and 2
1
⁄ 2 " Alternative Wood Blinds

INSTALLATION
5
Mount the Installation Brackets — Inside or Ceiling Mount
Bracket Shims (Optional)
Bracket shims are used to gain clearance for valance
clips with inside or ceiling mounts. One shim for each
end bracket and two shims for each intermediate
bracket are included.
 With each end bracket, first fold the shim and then
position it on top of the end bracket to gain the
required clearance.
 With each intermediate bracket, stack two
unfolded shims.
NOTE: Bracket shims may also be used to level the
blind whenever the mounting surface is uneven.
The shims can be cut along their fold line to make
them fit.
Attach the End Brackets
With inside or ceiling mounts, attach the two end
brackets flush against the sides of the window casement or to the ceiling. Choose the most
appropriate of the following mounting methods:
 Inside mount only (Side/Top Mount): Mount the end brackets with one screw through
a side hole and one screw through a top hole, as shown below left.
 Inside mount only (Side Mount): Mount the end brackets with two screws through
diagonal side holes.
 Inside or ceiling mount (Top Mount): Top mount the end brackets with screws through
the two top holes, as shown below right.
 Ceiling mount only: If the end brackets are flush with the back wall, attach them with
one screw through a top hole and one screw through a rear hole.
Side/Top
Mount
Top Mount
One Shim
Folded Over
Two Shims
Stacked
End
Bracket
Intermediate
Bracket
One Shim
Folded Over
T
wo Shims
Stacked
End
Bracket
Intermediate
Bracket

INSTALLATION
6
 Use a
3
⁄ 32 " drill bit to drill holes for the mounting screws.
 Attach the end brackets using the screws provided.
IMPORTANT: The front edges of the end brackets must align.
NOTE: For blinds with 2
1
⁄ 2 " slats, spacer blocks are used with inside mounts to position
the end brackets a minimum of
3
⁄ 8 " away from the glass. The spacing prevents the slats
from rubbing the glass when they are tilted open.
Attach the Intermediate Brackets (If Required)
 Evenly space the intermediate bracket(s) between the two end brackets.
 Adjust spacing if needed to avoid interference with internal headrail mechanisms.
 Attach the intermediate bracket(s) with two screws through diagonal top holes.
IMPORTANT: The rear of the end brackets and intermediate bracket(s) must align.
Proceed to “STEP 2 — Connect the Power Cable” on page 10.
Intermediate
Bracket
End
Bracket
End
Bracket
Space Evenly Space Evenly

INSTALLATION
7
Mount the Installation Brackets — Outside Mount
To attach the end brackets, a flat vertical surface of at least 1
3
⁄ 4 " is required for 1
3
⁄ 8 ", 2", and
2
1
⁄ 2 " slat sizes.
Mark the End Bracket Locations
 Mark where the ends of the headrail will be located.
 Center the headrail over the window opening at the desired height.
Use a pencil to lightly mark each end of the headrail.
 Alternatively, measure the width of the headrail and use that
width to mark the headrail end points over the window opening.
 Make a second mark
1
⁄ 4 " to the outside of the headrail
end marks. The outer marks are where the outside
edges of the end brackets will be located.
Attach the End Brackets
NOTE: The illustrations in this section show spacer blocks mounted with the end brackets
for 1
3
⁄ 8 ", 2", and 2
1
⁄ 2 " slat sizes. Spacer blocks are required for all outside mount 2
1
⁄ 2 " blinds,
unless extension brackets are used. Spacer blocks are optional for 1
3
⁄ 8 " and 2" slat sizes.
 Align the outside edge of each end bracket with the outer marks and mark diagonal screw
holes.
 Use a
3
⁄ 32 " drill bit to drill holes for the mounting screws.
Mark
Measure and Mark
1
∕ 4 " Out from
Ends of Headrail
Mark

INSTALLATION
8
 Attach the end brackets using two screws
through diagonal holes.
 If using spacer blocks, use #6 screws
long enough for a secure installation
(2
1
⁄ 2 " long screw is recommended).
IMPORTANT: The tops of the end
brackets must align.
CAUTION: The rear of the end
brackets or spacer blocks must be flush
against a flat mounting surface. Do not
mount end brackets on acurved
molding.
Attach the Intermediate Brackets (If Required)
 Evenly space the intermediate bracket(s) between the two end brackets.
 Adjust spacing if needed to avoid interference with internal headrail mechanisms.
 Attach the intermediate bracket(s) with
two screws through diagonal holes.
IMPORTANT: The tops of the end brackets
and intermediate bracket(s) must align.
Intermediate
Bracket
End
Bracket
End
Bracket
Space Evenly Space Evenly