HUROM H-300E Series User manual

※ 발주용 인쇄시 본 페이지(시방서) 삭제 후 진행
시방서
DESIGN SPECIFICATION
R&D2본부 디자인팀 자재명(자재번호 / 파일명 / 버전) : 작성일 :
❶ 사이즈
❷ 인쇄도수
❸ 지류
❹ 페이지
❺ 제본
❻ 후가공
1. 자재 사양
2. 기재 언어
3. 제작 및 수정일자
4. 수정사항
※ 발주용 인쇄 시 필히 본 페이지(시방서) 삭제 후 진행하세요. 본 파일은 시방과 인쇄파일을 포함합니다. 유관의 부서와 업체의 견적 / 사양 / 발주 인쇄 진행 / 품질검사 외에는 사용을 금합니다.
인쇄물 시방서 개정 : 19' 11
전주경 4DC010870 사용설명서 통합 H300E Series 영문 _V.01 2021. 08. 23
1. 2021. 08. 23_V.01
영문
150 x 220 mm
표지- 1도 인쇄
내지- 1도 인쇄
M 메트지 100g
12페이지(표지포함)
중철
없음

TM

02
CONTENTS
p.02
p.03
p.04
p.06
p.07
p.08
p.09
p.10
p.11
01 You should read <Safety Precautions>
02 You should follow <Safety Precautions>
03 Precautions are classified as follows.
1. Read 'Precautions for Safe Use ' (p. 2~3) and use
the appliance properly.
2. After reading the manual, keep it in a convenient
location for future reference.
3. Do not use it abroad which has different power
supply and voltage.
4. Any quality improvements is subject to change
without notice.
Before Reading Manual
1. Precautions for Safe Use
Do not remodel it under any circumstances. Also, do
not attempt to dismantle or repair it yourself.
Do not insert any foreign objects such as a finger
or iron pin into any crack or hole in the product
body. It may cause a fire, electric shock, injury and/or
malfunction. For after-sales service and maintenance
of a product, contact the HUROM Customer Service
Center.
When the power plug is damaged, do not repair or
remodel it yourself and, instead, visit an after-sales
service center or branch store.
Do not get wet or splash water on the product body.
Make sure that no water or foreign material goes into
the product's power switch.
Do not control the power switch with wet hands.
For safety, ground the power outlet at all times.
Also, do not ground it to a gas pipe, plastic water pipe,
or telephone line. Make sure to use a grounded outlet.
Do not attempt to dismantle any parts of the
chamber set or insert foreign objects such as a finger
or spoon into the inlet or juice outlet during operation.
Do not use it within children's reach. Children should
be carefully supervised so that they do not play with
this device. There is a risk of an injury or malfunction if
children accidentally hit and knock it down.
A person who is not familiar with handling the
product should not use it him/herself. Anyone with
physical or mental problems or who lacks experience
and knowledge should not use it without a supervisor
present.
Do not use the product while wearing or holding any
items with magnetic force (e.g. magnetic bracelets).
Placing magnetic objects near the product may cause
malfunction.
Caution A violation of any of the caution marks
may lead to a serious injury or death.
Do not operate the product unless the product body
set and chamber set are securely connected.
If there is a gas leak, etc., do not touch the power
cord but, instead, open the windows and thoroughly
ventilate the area.
If the Multi-screw stops during operation, the
product automatically rotates in reverse and then
starts normal operationagain. If the power is unstable
and a reverse rotation does not work while the Multi-
screw's rotation is stopped during operation, press the
power switch for over 1 second to activate a reverse
rotation and then press the power switch again briefly
to start a normal operation.
Do not move the product body, or disassemble or
assemble the chamber set or parts during operation.
Make sure to stop the operation and pull out the power
cord beforehand.
Warning A violation of any of the warning marks
may cause a serious injury or death.
Do not insert or pull the power cord with wet hands.
Use the right voltage only as specified on the
warranty cardand theproductspecifications. Failure
to follow this instruction may result in electric shock,
fire, or performance impairment. Connecting to a
different voltage may shorten the motor's lifespan or
cause malfunction.
Securely insert the power cord plug all the way into
an outlet.
Do not bend, tie, damage or pull the power cord by
force, or place it near a high temperature or heat
such as a gas stove. Also, do not place any heavy
object on top of the product, wedge it into a narrow
space, or alter it.
1. Precautions for Safe Use
2. Precautions During Use
3. Power Switch Guide /
4. Precautions Before Juicing
5. How to Assemble
6. Assembly and Disassembly of Silicone
7. How to Use
8. When Multi-screw Stops During Use
9. How to Disassemble and Clean
10. Before Requesting Repair
Instruction Manual [ Home use only / Warranty not included ] | H-300E Series

03
English
When using the product, be careful so that a tie, long
necklace, scarf, etc. doesn’t get into the inlet.
Place this product on an even and stable surface for
use.
When inserting ingredients into the inlet, do not use
a chopstick, spoon, any hard object or anything other
than the pusher.
Do not use the product for more than 30 minutes
continuously each time. It may overheat the motor to
cause malfunction. To operate it again, completely stop
the device for about 5 minutes before use.
Do not exert any excessive shock to or drop the
product.
If the device produces any unusual sounds,
excessive heat or smoke, stop using it immediately
and contact the Customer Service Center. The smell
experienced when using a new product will naturally go
away over time.
Pull the power cord plug from the outlet when it is
not in use. Also, when pulling the power cord, make
sure to grab the plug to pull it.
Do not clean the product at a temperature of 80°C
or higher. Do not place it in a dishwasher, dryer,
microwave, etc. It may cause malfunction and/or
deformation of parts.
The product weighs approximately 6.2 kg. When
moving the product, make sure to securely hold the
product body with both hands. If you move it by holding
just the chamber or the sides of the product body, the
body may fall to cause a bodily injury or malfunction.
Do not use this household-use product for
commercial purposes. Excessive extraction of a
large amount of ingredients may cause damage
to the parts. In case it is to be used for commercial
purposes, please contact the Customer Service Center
on the method of use.
Make sure to thoroughly understand how to
prepare ingredients and prepare them properly
before inserting them.
-Poorly prepared ingredients may hinder the
extraction process and/or cause damage to the
product.
Ingredients in need of extra care
-When using soft ingredients alone such as bananas,
ripened kiwi and tomatoes, the juice may stagnate
inside the chamber, which can make juicing difficult.
Please add other ingredients that are not too soft.
-When inserting walnuts, peanuts, almonds,
sunflower seeds, pine nuts, beans, etc., add only a
small amount or add them with other ingredients after
soaking them in water.
2. Precautions During Use
Ingredients unable to be juiced
- Do not insert ingredients that cannot be juiced such
as sesame seeds, coffee beans, Chinese peppers, tree
barks and pine needles. Do not insert mudfish, eels,
shrimp, marsh snails, squids, etc.
- Do not insert fruits soaked in alcohol, honey or sugar
(grapes, raspberries, mulberries, etc.) and enzymes
(glasswort, rock pine enzymes, etc.).
- Do not insert ingredients whose attributes make
them difficult to be juiced such as silverberries, aloe,
cactus, quince, yams, kudzu root, sugar cane, acorn
and dandelions.
- Do not insert boiled ingredients such as boiled
potatoes and sweet potatoes.
- Do not insert ice made by freezing water.
It is recommended that you consume extracted
vegetable juice immediately, if possible, and do not
refrigerate it for a long period of time.
Do not use this product for pulverizing grains. It
may cause damage or malfunction.
Do not re-extract juice from pulp that has already
been juiced.
Do not conduct any idle run of the product before
inserting any ingredients.
Do not insert ingredients into the hopper above the
guided limit mark.
Do not use it for more than 30 minutes
continuously.
- It may overheat the motor to cause malfunction.
However, when using it continuously, pause the
operation and use it after a break of over 5 minutes.
Do not insert a chopstick or spoon into the juice/
pulp outlet during operation.
When inserting ingredients, do not use anything
other than the pusher. It may damage the parts or
cause a bodily injury and/or malfunction.
Do not operate the power switch with wet hands.
- It may cause electric shock, short circuit and/or fire.
Do not get foreign substances on or near the power
switch.
Use it with the juice cap open.
- The juice can flow backwards into the hopper if the
juice cap is closed while juicing.
Do not use it when the top of the product body is
wet from extracted juice or water.
Note
1. Withered ingredients, which have been stored for
a long time in the refrigerator, or frozen fruits may
produce only a small amount of juice or none at all.
2. If the product is not cleaned immediately after
use, the pulp may dry up, which makes it difficult to
disassemble and clean it and also cause performance
impairment. So, if possible, clean it immediately after
use.

04
정회전
역회전
정지상태
작동스위치 정회전
역회전
off(정지) 정지
Before operating the product,
press the power switch. ※If you have an allergy, make sure to select
proper ingredients for your body when
preparing the ingredients.
※For the method of and notes on using the
device for each ingredient, please refer to the
recipe book.
※Prepare ingredients in sizes able to be
inserted into the hopper. If you want to juice
a large volume or perform fast juicing, cut
the ingredients into smaller pieces before
inserting them. For about 1 kg, repeat the
"disassemble and clean after juicing" step for
use.
※Do not insert ingredients into the hopper
above the guided limit mark.
※When juicing soft fruits, the juice of the
ingredients may stagnate inside the chamber.
※When juicing fibrous fruits and vegetables,
the juice may thicken.
※Inserting the following ingredients, which
are impossible to be juiced, may lead to
damage or malfunction.
- Ingredients that cannot be juiced such as
sesame seeds, coffee beans, Chinese peppers,
tree barks and pine needles, as well as mudfish,
eels, shrimp, marsh snails, squids, etc.
- Fruits soaked in alcohol, honey or sugar
(grapes, raspberries, mulberries, etc.) and
enzymes (glasswort, rock pine enzymes, etc.)
- Ingredients whose attributes make them
difficult to be juiced such as silverberries, aloe,
cactus, quince, bananas, yams, kudzu root,
sugar cane, acorns and dandelions
- Boiled ingredients such as boiled potatoes and
sweet potatoes
- Ice made by freezing water
※ Do not use it for pulverizing grains.
※Refer to the instructions in
<Precautions During Operation> (refer to p. 3).
Operate / WHITE LED blinks
- It works when the power switch is briefly pressed in
the Standby Mode.
- It is used when activating the product for juicing.
- During operation, the white lamp blinks.
- If the hopper cover is opened during operation, the
product stops and the white lamp is lit. If the hopper
cover is closed again within 60 seconds, the operation
continues. But, if 60 seconds elapse, the operation
automatically stops and it switches to the Standby (stop)
state.
Stop / WHITE LED on
- This is used to stop the product's operation.
- The product stops when the power switch is briefly
pressed in the operation state.
- When stopped, the white lamp is lit.
※If the hopper cover is open or the chamber set is
not assembled, the white lamp is turned off.
※When 1 minute has elapsed from the Standby (stop)
state, the product enters the power saving mode
(light turned off). If the power switch is pressed or the
chamber set is assembled, the power saving mode is
deactivated and it switches to the Standby (stop) state.
Reverse rotation / ORANGE LED blinks
- This is used when the operation pauses or a reverse
rotation is needed due to excessive insertion of
ingredients during extraction.
- During a reverse rotation, the orange lamp blinks.
※It works only when the power switch is pressed
for over 1 second, and it stops when the switch is
released.
※If the Multi-screw stops during operation, the
product automatically rotates in reverse but, if the
power is unstable, the reverse rotation may not work.
In such a case, press the power switch for over 1
second to activate a reverse rotation and then press
the power switch again briefly to activate.
4. Precautions Before Juicing
3. Power Switch Guide

05
English
※For dry and viscous ingredients, mix them
with other ingredients for extraction. Remove
the peel and stalks, and also remove seeds, if
there are any.
Root vegetables
Carrots, beets, ginger, sweet potatoes,
potatoes, garlic, etc.
Wash the ingredients in running water to remove
dirt and other foreign substances. For fibrous
ingredients such as ginger, peel the outer skin
and cut them into small pieces. For long
ingredients, cut them vertically for extraction.
Leaf and stem vegetables
Celery, kale, cabbage, water parsley,
wheatgrass, chives, etc.
Cut the ingredients into 3-cm or shorter pieces
for extraction. Since leaf and stem vegetables are
rough and fibrous, they are not easily juiced and
can get caught in the Multi-screw.
• When juicing ingredients other than root, leafy
and stem vegetables, the juice may stagnate.
Frozen fruits
Fruits with thick peels, such as watermelons
and melons
Peel the outer skin and cut the ingredients into
smaller pieces to fit in the hopper inlet before
freezing them.
Seeded fruits, such as mangoes, peaches and
grapes
Use only frozen, seedless fruits. For fruits that
have hard, unchewable seeds, such as mangoes,
peaches and lemons, make sure to remove the
seeds and then freeze them before use. For
grapes, freeze the seedless kind for use.
Soft fruits and vegetables, such as bananas,
strawberries, kiwi and tomatoes)
Peel bananas, kiwi, etc. completely and cut them
into pieces that are 3 to 4cm-long that can fit in
the inlet before freezing them. For cherry
tomatoes, strawberries, etc., remove the stalks
and then freeze them.
• It is used to make slushes, smoothies, ice
cream, etc. that use frozen fruits.
• Cut the fruits into 2-cm pieces and freeze them
before use.
• Never use it for crushing or grinding ice or
other ingredients.
• Adding a large amount or large chunks at once
may jam the product so please add the
ingredients in small portions.
• As certain ingredients need extra care during
preparation, please refer to the following instructions on
how to prepare the ingredients.
• When juicing several times or in bulk, make sure to
cut ingredients into small pieces, and then repeat the
"disassemble and clean after juicing" step.
• For faster juicing, mince the ingredients into fine pieces.
Citrus fruits
Grapefruit, oranges, lemons, etc.
Prepare the ingredients by peeling and cutting them
into smaller pieces to fit in the hopper inlet. Remove
all hard, unchewable seeds before insertion.
Fruits with thick peel
Pineapples, dragon fruit, melons, watermelons,
pomegranate, etc.
Prepare the ingredients by peeling and cutting them
into smaller pieces to fit in the hopper inlet. Remove
all hard, unchewable seeds before insertion.
Seeded fruits
Grapes, apples, peaches, persimmons, plums,
cherries, pears, Korean melons, etc.
For ingredients containing hard, unchewable seeds
or large-sized seeds such as those in peaches, make
sure to remove the seeds first and cut and prepare
only the flesh. Hard seeds may stop the operation or
damage the parts. Apple seeds contain toxicity so
remove them as much as possible. For grapes, pluck
each grape from the bunch after cleaning them
horoughly. Do not extract only the ingredients that
are too soft; instead, mix them with other fruits and
vegetables.
Soft fruits
Single extraction (berries, cherry tomatoes,
pineapples, etc.)
※Thoroughly clean and cut the ingredients into
small pieces that can fit in the hopper inlet. For fruits
and vegetables with stalks, remove the stalks first.
Mixed extraction (strawberries, kiwi, bananas,
tomatoes, mangoes, etc.)
4-1. Multi-screw

06 5. How to Assemble
01 Insert the Bottom part of multi-screw(⑤) into the chamber (④), and insert the Top part
of multi-screw (③) as shown in the figure.
02 Firmly press down the Multi-screw set and assembled in the chamber.
03 Assemble the hopper cover (①-1) vertically onto the hopper (②-1).
04 Align the hopper [ ] assembly guide mark (②-3) with the chamber [ ] assembly
guide mark (⑤-2) to assemble them.
05 Turn the assembled hopper clockwise up to the chamber [ ] assembly guide mark.
If the internal parts are not assembled correctly, the hopper will not close.
06 Check if the discharge cover and the loop (⑤-4) of the chamber are properly closed.
1. Lift the discharge cover to close it and fasten it with the loop.
2. If the packing is not correctly assembled or the lever is not properly closed, juice may leak or
the lever may open during extraction.
07 Place the correctly assembled chamber set onto the product body (⑥).
Assemble the chamber set first and then install it on the product body.
01
01
03
03
04
04
07
07
06
06
05
05
③
⑤
⑤
④
④
①-1
②-1
⑤-2
⑤-2
②-3
②-3
⑤-4
⑤-4
⑥
⑥
02
02

07
English
6. Assembly and Disassembly of Silicone
※Silicone packings are consumables that are
recommended to be replaced once every 6 to 12
months. They are available for purchase through
the Customer Service Center.
01
01
02
02
03
03
(The juicer may leak if the product is not assembled
properly.)
Hold and take out the packing as if you are
pulling it back.
After cleaning, insert one side of the packing
first as if you are hooking it.
Insert the remaining part and press down the
perimeter.
Extraction Packing
After cleaning, insert in a way that the round
side of the packing faces outward while the grid
grooves face upward.
Assemble the packing as shown in the figure.
Juice Cap Packing
Hopper Packing
01
01
02
02
03
03
Grab one side and pull it back to detach it.
After cleaning, check the top and bottom of
the packing and insert it as if you are hooking
one side.
Firmly press the remaining part of the
packing without any folded area.
Chamber Packing
Seal Packing
01
01
02
02
01
01
02
02

08
04
04
07
07
05
05
08
08
06
06
09
09
01
01
03
03
02
02
정회전
역회전
정지상태
작동스위치 정회전
역회전
off(정지) 정지
정회전
역회전
정지상태
작동스위치 정회전
역회전
off(정지) 정지
7. How to Use

09
English
01
01
02
02
정회전
역회전
정지상태
작동스위치 정회전
역회전
off(정지) 정지
정회전
역회전
정지상태
작동스위치 정회전
역회전
off(정지) 정지
01 Open the hopper cover.
①Press the lever of the hopper cover to open it.
Insertion of an excessive amount of ingredients may
damage the product.
02 Add ingredients only up to the limit mark of the
hopper.
①For soft ingredients, mixing them with other ingredients
for extraction.
03 Close the hopper cover and keep the juice cap open.
①Before pressing the power switch, place the juice
container and pulp container first.
②The juice may flow backwards into the hopper if the juice
cap is closed during extraction. If the juice does not come
out even after opening the juice cap, open the hopper cover
and empty out the contents.
③ When the hopper cover is closed, the white lamp is lit.
04 Press the power switch briefly to start operation.
①The "click" sound during the operation of the product is
the sound of the chamber set and the motor being locked
together.
②During operation, the white lamp blinks on the power
switch part.
③If the Multi-screw stops during operation, the product
automatically rotates in reverse but, if the power is
unstable, the reverse rotation may not work. In such a case,
press the power switch for over 1 second to activate the
reverse rotation and then press the power switch again
briefly to activate.
④A timer, which automatically stops after about 5 minutes
from the start of operation, is set. If the power switch is
controlled during operation or the hopper cover is opened
and then closed, which pauses and then restarts the
machine, the timer is reset to 5 minutes again.
05 To add more ingredients during operation, use the
additional inlet or open the hopper cover.
①When the hopper cover is opened, the operation stops.
② Do not use anything other than the designated pusher.
③In case the Multi-screw spins but the ingredients fail to
be ground in the hopper during extraction, use the pusher
to press the ingredients down.
06 Empty out the pulp container and juice container so
that they are not filled up.
07 Let the machine operate for about 1 more minute after
all ingredients go down in the hopper.
① It slowly presses and squeezes the ingredients so it
takes some time until the last ingredient is juiced.
②Removing the remaining pulp by additionally operating
the machine after extraction makes it more convenient to
detach the hopper and clean the parts.
08 Once the juicing and pulp removal are finished, press
the power switch to stop the machine.
① The machine stops 3 seconds after it is stopped by the
power switch.
09 Pour any remaining juice by tilting the chamber
forward.
① For thickly concentrated juice made of tomatoes, etc., the
juice may still remain in the chamber.
01 If the Multi-screw stops during operation, the
product automatically rotates in reverse and then
goes into a normal operation. But, if the power
is unstable, the reverse rotation may not work.
In such a case, press the power switch for over 1
second to activate a reverse rotation. The reverse
rotation is a function that returns the ingredients
upward. It only works while the power switch is
pressed and, once you lift your finger from the switch,
the Multi-screw stops rotating.
02 After the Multi-screw is completely stopped after
a reverse rotation, press the power switch briefly
to start the operation again. When operating the
extraction or reverse rotation function, make sure
to press the power switch after the Multi-screw has
completely stopped moving.
Note
If the machine does not work even after following the
above steps, pull the power cord plug from the outlet,
detach the chamber set, wash it and use it again. Due
to its characteristics, the motor will not stop at once
but, instead, continue to spin slowly in the direction of
operation before coming to a complete stop.
8. When Multi-screw Stops
During Use

10 9. How to Disassemble and Clean
※ After the product stops operating completely,
pull the power cord plug with dry hands. Even
after the product is stopped, the motor will slowly
come to a stop so wait about 3 seconds before
detaching the chamber set.
01 Detach the chamber set from the product body.
Turn the hopper to open it and then sequentially pull
each of the parts to disassemble them.
02 Wash the parts with a cleaning brush under
running water.
03 Open the discharge cover and juice cap to clean
the chamber.
04 Wipe the product body with a damp towel or soft
cloth.
05 Detach and wash silicone packings after use.
- Residue may still be stuck.
(hopper packing, juice cap packing, extraction
packing, seal packing, chamber packing)
06 You can sterilize the parts by soaking them in
warm water diluted with baking soda, citric acid or
vinegar.
※ Failure to clean the product immediately after use
may cause its stainless steel parts and other parts
to corrode or become discolored due to salt and pulp
from the ingredients. Also, contaminants may be
dried up and stuck inside, which makes it difficult to
disassemble and clean them and may also cause
performance impairment. Be sure to clean and air-
dry it completely immediately after use and store it in
a clean place. For long-term storage, use a cleaning
brush to wash it. Do not clean with boiling or high-
temperature water or use a cleansing sponge, steel
sponge, abrasives and other sharp cleaning tools. Do
not place it in a dishwasher or dish dryer.

11
English
10. Before
equesting Repair
01. When it starts operating, a
"click" sound is heard.
It is the sound of the motor being assembled with the Multi-screw. This is not a
malfunction.
02. It does not operate only
with the product body.
Check if the chamber set and product body are properly assembled. Make sure to turn
the power off when assembling or disassembling the product.
03. Assemble it so that it is
aligned with the safety sensor.
Check if it is assembled in accordance with the guide mark. Make sure to turn the power
off when assembling or disassembling the product.
04. It does not work.
Check if the power cord is properly inserted. The machine may not work after a long
period of (30 minutes or longer). It will operate normally after the heat of the product
body (motor) cools down.
05. It stops during a normal
operation.
Check if the hopper is properly assembled. If the hopper is assembled incorrectly, the
product will not work. It will operate only when the lock symbol on the chamber and the
hopper's assembly guide mark are assembled in a way that they face each other. Check
if the product is assembled according to the steps specified in the assembly guide. Refer
to the assembly guide page (page 6). Haven't an excessive amount of ingredients or
extremely thick ingredients inserted? Refer to Page 9 of the manual to activate a reverse
rotation.
For safety, a timer, which automatically stops after about 5 minutes from the start of
operation, is set. Press the switch again briefly to start operation.
06. There are crack marks
caused by a Multi-screw or
scratch marks at the top of the
Multi-screw.
In the process of making the molding, curve-shaped marks are created on the sides
and top of the Multi-screw in addition to the straight-lined mold marks. They are normal
parts and do not affect the operation at all.
07. Juice leaks through the
pulp outlet immediately after
the ingredients are inserted.
Depending on the inserted ingredients, small amounts of juice may leak through the
pulp outlet.
This is not a product defect but, rather, a phenomenon caused by the characteristics of
the ingredients. The leakage will stop once the product starts running. If the leakage
continues, contact the Customer Service Center.
08. Juice flows back into the
hopper.
Did you extract juice with the juice cap closed? When juicing with the juice cap closed, the
juice may flow backward into the hopper. If the contents are not sufficiently discharged
even after opening the juice cap again, open the hopper cover and empty out the contents.
09. Juice leaks between the
hopper and the chamber, or
between the chamber and the
product body.
Is the hopper packing or chamber packing assembled correctly? The juice will leak if the
hopper packing or chamber packing has been assembled upside-down or incompletely.
Check if the packing is assembled properly.
10. The hopper does not open.
There may be excessive pulp remaining inside. Operate the produce to discharge the
pulp inside or repeat the process of activating a reverse rotation for about 10 seconds and
then stopping 2 to 3 times. Then, the hopper will open without any issue.
Weren't any foreign substances or solid matters (hard seeds such as persimmon
seeds) inserted? If any foreign substances or solid matters are inserted, parts may be
damaged more seriously when attempting a reverse rotation so contact the Customer
Service Center and request for after-sales service.
11. The chamber shakes
(during juicing).
The product may wobble slightly due to the motions of the product body's motor.
Depending on the ingredients' characteristics (hard or tough), motions are generated
in various magnitudes. This is not a malfunction but, rather, a normal phenomenon
observed when the Multi-screw rotates. Compared to soft ingredients with much water
content, relatively harder ingredients may seem to produce a greater shaking (e.g.,
carrots, potatoes, radishes, beet, kohlrabi, etc.)
12. The discharge cover
is closed but the pulp is
discharged.
Even if the lever is closed, pulp will be discharged naturally. Depending on the
ingredients used, there may be a difference in the amount and speed of discharge.
13. An unusual noise is heard
while juicing.
It is a natural sound produced when ingredients are being crushed. If the ingredients are
hard or tough like apples, carrots, cabbage, celery, beets, etc., the extraction noise may
be louder than that heard when juicing softer ingredients.
14. The Multi-screw stopped
during operation but a reverse
rotation does not work
automatically.
If the power is unstable, the product may not perform a reverse rotation automatically.
Refer to Page 9 of the manual and activate a reverse rotation.
15. During straining, it
automatically ends before the
5-minute timer ends.
It is a function that automatically shuts down to protect the product in case the automatic
reverse rotation is operated often during straining. This may occur if it is impossible to
strain or if uncut ingredients are added. Please refer to Page 5 of the manual for the
instructions on each ingredient and insert the ingredients accordingly.
Check the following before asking for repair. For follow-up service and any inquiry
you may have while using the product, please contact our Customer Center, or
homepage at http://www.globalhurom.com Check the manufacturer’s number or
the number under the barcode when requesting for follow-up service or parts.

4DC010870_V.01
MADE IN KOREA | www.globalhurom.com
Copyright© All Rights Reserved by HUROM
TM