Hyco Ariano AR1000T Specification sheet

Product Instruction Manual
Ariano
AR1000T, AR1500T, AR2000T
Glass Panel heater
Version 3.2 Jan 2015
V19.2,1
DayT imer
MON
08.00

2
Thank you for purchasing a Hyco Ariano glass panel heater. Please ensure you read and
understand these instructions to ensure safe installation and operation.
The Ariano is ideal for a wide range of fixed installation heating applications in the home and
office environment. The Ariano is ecodesign compliant; energy savings features include open
window function and a 24/ 7 electronic timer.
Key Features
• Slimline, modern, glass fronted design
• 24/ 7 electronic timer with remote control
• Reduced energy wastage with open window detection
• Frost protection feature
• Full or half power setting
• IP24 splashproof
1. Important safety points
The electrical installation must be carried out by a qualified electrician in
accordance with the current edition of the I.E.E. Wiring Regulations.
Only connect the unit to a single-phase supply with a mains voltage as specified
on the rating plate.
If the heater is located in a bathroom, it must be installed so that switches and
other controls cannot be touched by a person in the bath or shower.
Only use the mounting bracket supplied and do not modify the bracket in
any way.
WARNING: To avoid overheating, do not cover the heater.
The supply cord cannot be replaced by the user. If the cord is damaged the
appliance should be returned to the manufacturer or an authorised service
agent for replacement.
The heater must not be located immediately below or above an electrical socket
outlet.

3
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards involved.
Children of less than 3 years should be kept away unless continuously
supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the
appliance provided it has been placed or installed in its intended normal
operating position and they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than 8 years shall not plug
in, regulate and clean the appliance or perform user maintenance.
CAUTION: Some parts of this product can become very hot and cause burns.
Particular attention must be given where children and vulnerable people
are present.
2. Installation
Wall Mounting
•Select a suitable location for the install and ensure the minimum spaces around the
heater are maintained to ensure good airflow and safe operation of the heater.
DayTimer
MON
08.00
Min 1000mm
Min 100mm Min 100mm
Min 100mm
1

H
H1
L
LL11
LL2
H2
• Ensuring a horizontal level, offer the bracket to the wall and mark the two upper
holes and the lower central hole as per the dimensions provided in the table above.
• Drill the three holes into the mounting surface and insert the wall plugs supplied.
• Insert the supplied screws into the wall plugs, leaving 5mm of thread protruding.
• Hang the heater to the screws by locating them into the centre of the three
corresponding brackets and then sliding the unit to the right and down to secure.
Specification
Model L(mm) H(mm) L1(mm) L2(mm) H1(mm) H2(mm)
AR1000T 515 450 220 110 350 270
AR1500T 675 450 380 190 350 270
AR2000T 835 450 540 270 350 270
4

Electrical installation
The electrical installation must be carried out by a qualified electrician in
accordance with the current edition of the I.E.E. Wiring Regulations.
•Connection should be made to the fixed wiring of the property via a double pole
fused spur with a break capacity of no less than 13amps.
•Electrical connections should be made as follows:
Green/Yellow earth wire to the terminal marked “ E” or
Brown/Red live wire to the terminal marked “ ”
Blue/Black neutral wire to the terminal marked “N”
Circuit diagram
Recommended mounting height
(bottom edge of dryer above nished oor)
M 43”
L 41”
C 39”
C 33”
1
5
Heating element
KSD thermostat KSD thermostat
Tem p er at u r e sensor
Switch
Tip over switch

3. Operation
Control panel overview
14. Up selector
15. Manual/Auto mode
16. Target temperature
17. Set button
18. Full/Half power button
19. Ok button
1. Window open indicator
2. Auto mode indicator
3. Manual mode indicator
4. Timer period indicator
5. Hour indicator
6. Day indicator
7. Minute indicator
8. Timer on
9. Full power
10. Half power
11. Element on indicator
12. Standby on/off button
13. Down selector
Setting t e clock
•Turn the heater on via the power switch at the lower right-hand side of the unit.
Turn on the display screen by pressing the standby on/off button.
•Hold down the M/A and buttons on the remote control or on the touch screen
simultaneously for 2-3 seconds, a beep will sound, and the current day setting will flash.
•Use the buttons to cycle to the correct day and press the M/A button to store.
•The hour indicator of the display will flash, use the buttons to cycle to the
required value and press the M/A button to store.
•The minute indicator of the display will flash, use the buttons to cycle to
the required value and press the M/A button to store.
•The current day and time will now show on the display.
The unit has a built-in memory that can retain the time for several days if the power is
switched off to the unit. If the unit is off for longer periods the day & time may need to
be reset upon next start up.
15 14 13 12
16
8
9
10
11
18
17
13
12
15
14
19
1 2 3 4 5 6 7
.
6
.
.
.
.
.
.

Setting t e target temperature
•To set the target temperature of the heater use the buttons on the touch
screen to cycle to the desired target value, allow the display to flash for several
seconds, when it stops flashing the display will show the new stored target
temperature.
Switc ing between Full/Half power
In order to use this feature, the remote control must be used.
•Press the power select button on the remote control to toggle between Full/ Half
power setting. The current setting used will be displayed by the power icons
on the display.
Manual mode
When the heater is in the manual mode (M), it will allow the user to simply switch the
heater on/off via the standby button.
In this mode, the heater can be programmed to run on and automatically switch off
and go into standby at any specified time within the next 24hrs. The feature can only
be used via the remote control - see “Manual timer programming” section. Once the
pre-defined time is reached and the heater has switched itself off it will need to be
manually turned back on again at which point it will revert to operating in manual
mode. It is strongly recommended to consider setting a timed operation using the
auto mode where anticipated usage is predictable to avoid energy wastage.
Auto mode
This mode allows the heater to be operated by a user defined schedule. This offers up
to four separate periods of operation to be defined for each day of the week. This
feature is strongly recommended where heat demand is predictable as it can help
reduce energy wastage. In addition, this allows spaces to be heated in anticipation of
the demand without the need for somebody to be present to turn it on; for example,
in an office environment where staff arrive to begin work at 8.30am, turning the heater
on at 8am to pre-warm the room. The operating times can only be programmed into
the heater via the remote control (see “Auto timer programming” section).
Switc ing between Manual/Auto operation mode
•Press the M/A select button on the heater touch screen to toggle between the
two modes. Confirmation of the current mode will be shown in text form on the
heater display.
7
.
.
.
•Turn on the display screen by pressing the standby on/off button.
•Turn on the display screen by pressing the standby on/off button.

Manual (run on) timer programming
In order to use this feature, the remote control must be used.
Auto timer programming
In order to use this feature, the remote control must be used.
•Repeat the process for each of the seven days of the week as required.
The default setting for each day and each slot is off.
8
A
.
A
.
A
.
A
.
.
.
.
.
.
.
•Turn on the display screen by pressing the standby on/off button.
•Select “M” mode via the remote control by pressing the M/A button until "M" is displayed
on the touch screen in the manual mode indicator.
•Press the “Set” button on the remote control and the current day and hour will flash. It is
only possible to specify a time within the next 24hrs for the heater to enter standby mode.
•Next the exact time of shut down needs to be defined. Cycle to the desired hour before
pressing “Set” to confirm and then repeat for the minutes before pressing “Set” to complete
the setting. If the shut down time runs into the next day, you will see the current day on the
day indicator automatically cycle to the next day.
•Turn on the display screen by pressing the standby on/off button.
•Select “Auto” mode via the control by pressing the M/A button until A is
displayed.
•Press the “Set” button on the remote control and the current day will
flash. Use the buttons to cycle to the required day and press
the “Set” button to confirm.
•Use the buttons to select the starting hour for the first period of
operation and press the “Set” to confirm. The next flashing number is the
hour to stop operation, use the buttons to cycle to the required
value and press the “Set” button to confirm. (the picture shows slot
1 programmed to start up on Monday at 08.00 and then shut down
at 17.00)
•The starting hour of the second period of operation will now flash,
repeat the previous steps as per the first period of operation. Up to four
slots of operation are available if required. If the further slots are not
required press the “OK” button at any stage to complete the
scheduling for the current day.

When the heater is in a defined period of non-operation it will automatically go into
standby mode. It can be woken up by pressing any button in order to alter settings but
will go back into standby if no further button is pressed within 10 seconds.
Setting t e c ild lock
• Press the buttons simultaneously and hold until a beep sounds. The
target temperature display will be replaced by “[ ]” icon to indicate the panel is locked.
•Repeat the first step to unlock the heater.
Open Window detection
• The unit has smart technology to prevent unnecessary energy wastage. If a window
or door is left open the heater will detect a temperature drop and stop heating. The
unit will beep and the open window icon will display. To restart the heater, press the
standby button twice and the unit will begin in its last operating mode.
4. Maintenance & Trouble shooting
Maintenance
The heater should be inspected and cleaned periodically, attention should be given to
the inlet grilles at the base of the unit and the outlet louvres at the top of the heater.
Ensure they are cleared of dust or other debris that may causes a blockage and in turn
reduce the airflow in and out of the heater, which if unchecked may lead to the unit
running at hotter temperatures.
• Ensure the heater is isolated from the power supply and has fully cooled down
before commencing any cleaning of the heater.
• Use a soft brush or vacuum cleaner to gently remove any debris from the inlet grilles
and outlet louvres.
• Use a non-abrasive, damp cloth with soapy water to clean the main body of the
heater. Take care not to use excessive amounts of water that could run into the main
body of the heater.
Sooty deposits can adhere to the louvres of the heater and the surrounding surfaces of
the heater install. This can be caused by excess dust in and around the heater burning
off the heating element after prolonged periods of non-use. This does not indicate an
over-heat occurrence and the effects can be reduced with regular cleaning of the heater.
9
.
.

5. Specifications
AR1000T AR1500T AR2000T
Supply 230v~ 50Hz
Power (half/full) 500/1000W 750/1500W 1000/2000W
Water resistance IP24
Class I
Weight 5.8kg 7.5kg 9.25kg
Thermal protection Auto reset thermostat x 2
Size (w x x h) 515x105x675x105x 835x105x
450mm 450mm 450mm
Model Identifiers: Ariano panel eaters AR100T,AR1500T & AR2000T
Item Symbol Value Unit
AR1000T AR1500T AR2000T
Heat output
Nominal heat output Pnom 1.0 1.5 2.0 kW
Minimal heat output Pmin 0.5 0.75 1.0 kW
(indicative)
Maximum continuous Pmax, c 1.0 1.5 2.0 kW
heat output
Auxiliary electricity consumption
At nominal heat elmax 0 kW
output
At minimum heat elmin 0 kW
output
In standby mode elSB 0.37 W
10

11
Item Unit
Type of eat input, for electric storage local space eaters (select one)
manual heat charge control with integrated thermostat No
manual heat charge control with room and/or outdoor No
temperature feedback
electronic heat charge control with room and/or outdoor No
temperature feedback
fan assisted heat output No
Type of eat output/room temperature control (select one)
single stage heat output and no room temperature control No
two or more manual stages, no room temperature control No
with mechanic thermostat room temperature control No
with electronic thermostat room temperature control No
electronic room temperature control plus day timer No
electronic room temperature control plus week timer Yes
Ot er control options (multiple selections possible)
room temperature control, with presence detection No
room temperature control, with open window detection Yes
with distance control option No
with adaptive start control No
with working time limitation No
with black bulb sensor No
6. Guarantee an service policy
This product is covered by a standard parts or replacement warranty for a period of
12 months from the date of purchase.
If there is a manufacturing defect within the warranty period we will send spare parts,
repair and return the unit or, at our discretion, supply a replacement product.
Incorrect installation and failure to follow correct operating instructions are excluded.
Consequential costs such as labour charges or damage to surroundings are expressly
excluded.

hyco.co.uk
Hyco Manufacturing td
Normandy Court
Express Way
Castleford, WF10 5NR
T 01924 225 200
F 01924 225 210
E [email protected]
INFORMATION FOR CORRECT DISPOSA OF THE PRODUCT IN ACCORDANCE WITH THE
EUROPEAN DIRECTIVE 2012/19/EU.
At the end of its working life this equipment must not be disposed of as household
waste. It must be taken to a local authority waste collection centre or to a dealer
providing this service. Disposing of electrical and electronic equipment separately
enables its components to be recovered and recycled to obtain significant savings in
energy and resources. In order to underline the duty to dispose of this equipment
separately, the product is marked with a crossed out dustbin.
Contact us
If you experience a problem with this product you should first contact our service
department on 01924 225 200 before taking any further action.
Experience has shown that issues can often be resolved without the need to return
or uninstall the product.