Hyco Zephyr DF20 User manual

Product Instruction Manual
Zephyr
DF20
2.0 kW Downflow fan heater
Version 3.2 Jan 2015
V15.9/5
Zephyr_Layout 1 05/10/2015 14:34 Page 1

2
Thank you for purchasing the Hyco Downf ow Fan Heater. The Downf ow
heater has two selectable settings. Setting I gives a fixed 1kw output and
setting II also gives a fixed 1kw output plus a further 1kw which is
thermostatically controlled. Please read and understand these instructions
before commencing installation, and leave them with the user when
installation is complete.
1. Important safety points
•The electrical installation must be carried out by a qualified electrician in
accordance with the current edition of the I.EE wiring regulations.
•Switch off the mains before commencing installation.
•Electrical connection must be made to the fixed wiring if the property by means of a
connection box. The installation must be fitted with a double pole isolating switch,
with a break contact distance of at least 3mm and an RCD not exceeding 30 m A.
•Means for electrical disconnection must be incorporated in the wiring
installation in accordance with the relevant wiring and electrical regulations.
•nly connect the heater to a single phase supply with a mains voltage
as specified on the rating plate.
•Do not use this heater with a timer or any other device that switches the heater on
automatically, since a fire risk exists if heater is covered or positioned incorrectly.
•The heater must not be locked immediately below a socket outlet.
•If the cord of the appliance is damaged, discontinue use of this product and
contact the manufacturer for further instructions.
•Do not carry the appliance by holding the power cord.
•Always switch off the appliance when not in use.
•Do not let the power cord hang over the appliance.
Zephyr_Layout 1 05/10/2015 14:34 Page 2

3
•Do not let animals or children touch or play with the heater. Please note that
the hot air outlet gets very hot during operation.
•The downflow heater is not suitable for outdoor use.
•The mounting position of the heater should allow free movement of air
around the heater.
•Do not cover the heater as this may cause overheating.
•The heater must be installed so that switches and other controls cannot be touched
by a person in the bath or shower.
•The unit should be mounted at least 1m away from any combustible materials
such as furniture, curtains, bedding etc.
•Do not use the appliance in rooms less than 4m2.
The unit must not be used unless the cover is correctly fitted.
•Keep the fan heater clean. See the cleaning and maintenance section.
•Children aged from 3 years and less than 8 years shall only switch on/off the
appliance provided that it has been placed or installed in its intended normal
operating position and they have been given supervision or instructions concerning
use of the appliance in a safe way and understand the hazards involved. Children
aged from 3 years and less than 8 years shall not plug in, regulate and clean the
appliance or perform user maintenance
Caution - some parts of this product can become very hot and cause
burns. Particular attention has to be given where children and
vulnerable people are present.
Zephyr_Layout 1 05/10/2015 14:34 Page 3

2. Installation
Wall Mo nting
•The Downflow fan heater is to be wall mounted at a minimum height of 1.8m in
the upright position with the warm air vent facing downwards.
•Loosen the two screws at the top of the front of the heater and lift off the front cover
•Mark the position of the top two fixing holes ensuring they are level
•Drill holes using a 5mm drill bit and use the plugs and screws provided leaving
approximately 3mm of the screw protruding
•Hang the heater on the screws
•Mark the position of the third fixing hole using the heater as a template
•Remove the heater, drill the hole and insert the plastic plug
•Replace the heater and tighten the top two screws
•Secure the heater using the third fixing.
4
Wall
Top Fixing hole
300 min
1800 min
240
Wall or Other Adjacent Surface
Ceiling
Floor
250 min.
235
Zephyr_Layout 1 05/10/2015 14:34 Page 4

5
Wall
T
op Fixing hole
300 min
1800 min
240
Wall or Other Adjacent Surface
Ceiling
Floor
250 min.
235
Electrical
The installation, electrical connection and first operation of this appliance
should be carried out by a qualified installer.
•Electrical connection must be made to the fixed wiring of the property by means
of a connection box and protected by a 13A fuse.
•If you require a longer cable or need to replace the cable at any time, appropriately
rated cable should be used and fitted by a competent person.
•Select the desired mode of operation using the switch.
I = 1kW fixed
II = Max 2kW - Steps down to 1kW on thermostat control
Zephyr_Layout 1 05/10/2015 14:34 Page 5

NOTE: When used in small rooms of less than 10m3 the 1kw output should be
selected to avoid nuisance tripping of the cut-out
•Set the thermostat to the mid position (recommended setting).
•Refit front cover and secure.
•Switch power on.
3. Operation
Adjustment
•Switch off the mains power to the unit.
•Remove the front cover to access the interna s.
•Se ect the desired mode of operation using the switch.
•Turn the thermostat contro c ockwise to increase room temperature and
anti-c ockwise to decrease.
•Refit front cover and secure using the two screws.
Pull the cord to turn on/off the heater The unit has a thermal cut out that will
operate in the event of overheating. Before resetting the thermal cut-out, the
cause of the overheat should first be established and resolved.
To reset the thermal cut-out the power supply must be disconnected for several
seconds and then reconnected.
6
Fixing hole
Cable clamp
Terminal block
Thermostat control
Cable entry
1kW / 2kW selector
Zephyr_Layout 1 05/10/2015 14:34 Page 6

4. Maintenance
•Before cleaning, ensure the heater is unplugged and that it has cooled completely.
•Wipe the exterior of the heater with a soft dry cloth.
•Never use any chemical or abrasive cleaners.
•Use a vacuum cleaner to avoid a build up of fluff or dust in the heater.
5. Specifications
Supply 230V ~ 50Hz
Power 1 1000W / 2000W
IP Rating IP21
Dimensions (H x W x D) 240mm x 235mm x 125mm
Overheat protection Manua reset therma cut-out
Protection Doub e Insu ated
7
240
235 125
Zephyr_Layout 1 05/10/2015 14:34 Page 7

hyco.co.uk
Hyco Manufacturing Ltd
Normandy Court
Express Way
Castleford, WF10 5NR
T 01924 225 200
F 01924 225 210
E [e-mail]
INF RMATI N F R C RRECT DISP SAL F THE PR DUCT IN ACC RDANCE WITH THE
EUR PEAN DIRECTIVE 2002/96/E.
At the end of its working life this equipment must not be disposed of as household
waste. It must be taken to a local authority waste collection centre or to a dealer
providing this service. Disposing of electrical and electronic equipment separately
enables its components to be recovered and recycled to obtain significant savings in
energy and resources. In order to underline the duty to dispose of this equipment
separately, the product is marked with a crossed out dustbin.
6. G arantee and service policy
This product is guaranteed against faulty materials and manufacture for a period of one
year from the date of purchase. Hyco will in its sole discretion replace, repair or refund
any faulty unit. Incorrect installation and failure to follow correct operating instructions
are excluded. Consequential costs such as labour charges or damage to surroundings are
expressly excluded.
Zephyr_Layout 1 05/10/2015 14:34 Page 8