Hyco DF20LL User manual

0
Arezzo 2kW
Downflow Heater
DF20LL
Instruction Manual
Version 1.0 October 2014
Arezzo - DF20LL 9/10/14 14:13 Page 1

PLEASE READ THESE INSTRUCTIONS BEFORE
COMMENCING INSTALLATION. UPON COMPLETION
OF INSTALLATION ENSURE THE INSTRUCTIONS ARE
LEFT WITH THE USER/MAINTAINER OF THE PRODUCT.
Downflow 2kW
DF20LL
1. INTRODUCTION
Thank you for purchasing the Hyco Arezzo downflow heater.The Arezzo heater is a
thermostatically controlled wall mounted fan heater; it offers fan only operation as
well as 1 & 2kW heat settings. It is the ideal solution for heating small rooms such
as bathrooms and en suites.
2
Arezzo - DF20LL 9/10/14 14:13 Page 2

2. IMPORTANT SAFETY POINTS
THE APPLIANCE MUST ONLY BE CONNECTED TO A SINGLE PHASE
SUPPLY.
THE PRODUCT SHOULD ONLY BE CONNECTED TO A SUPPLY THAT
MEETS THE SPECIFICATIONS DETAILED ON THE RATING LABEL.
ELECTRICAL INSTALLATION SHOULD BE CARRIED OUT BY A
QUALIFIED ELECTRICIAN IN ACCORDANCE WITH THE LATEST
EDITION OF THE IEE WIRING REGULATIONS.
THE APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING
CHILDREN) WITH REDUCED PHYSICAL, SENSORY OR MENTAL
CAPABILITIES, OR LACK OF EXPERIENCE AND KNOWLEDGE,
UNLESS THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION
CONCERNING THE SAFE USE OF THE APPLIANCE BY A PERSON
RESPONSIBLE FOR THEIR SAFETY.
DO NOT USE THE HEATER IF THE POWER CORD SHOWS ANY SIGN
OF DAMAGE.
CHILDREN SHOULD BE SUPERVISED TO ENSURE THEY DO NOT
PLAY WITH THE APPLIANCE.
NOT SUITABLE FOR OUTDOOR USE.
WARNING: IN ORDER TO AVOID OVERHEATING, DO NOT COVER
THE HEATER.
THE SURFACE OF THIS APPLIANCE CAN BECOME HOT; NEVER LEAVE
VERY YOUNG CHILDREN OR VERY VULNERABLE PEOPLE UNSUPERVISED
WITH THE HEATER.
CHILDREN AND VULNERABLE PEOPLE SHALL NOT BE ALLOWED TO
CLEAN OR PERFORM MAINTENANCE OF THE HEATER UNSUPERVISED.
DO NOT USE THE HEATER IN CONJUNCTION WITH ANY AUTOMATIC
SWITCHING DEVICE SUCH AS A TIMER.AN OVERHEAT RISK EXISTS
IF UNATTENDED.
3
Arezzo - DF20LL 9/10/14 14:13 Page 3

3. INSTALLATION
THE HEATER CAN BE MOUNTED IN BATHROOMS BUT MUST ADHERE
TO THE LATEST BATHROOM ZONE FOR AN IP23 RATED ELECTRICAL
APPLIANCE.
THE HEATER MUST NOT BE LOCATED IMMEDIATELY BELOW A
SOCKET.
ONLY MOUNT THE UNIT VERTICALLY WITH THE OUTLET AT THE
BOTTOM OF THE HEATER (AS SHOWN)
THE HEATER MUST BE MOUNTED AT LEAST 1 METER AWAY FROM
ANY COMBUSTIBLE MATERIALS SUCH AS FURNITURE, CURTAINS,
BEDDING ETC...
DO NOT INSTALL THE HEATER WHERE SOMEBODY COULD EASILY
REACH IT WHILST IN THE BATH/SHOWER.
ENSURE THERE ARE NO HIDDEN CABLES OR PIPES BEFORE
COMMENCEMENT OF DRILLING.
1Ensure the minimum and maximum mounting distances are maintained.
4
1.8m
MAX
20cm
MIN
20cm
MIN
0
HOLE
19cm
9
2.3cm
FLOOR
WALL
1
Arezzo - DF20LL 9/10/14 14:13 Page 4

5
2Mark, drill and insert the supplied wall plugs as shown in the diagram.
3Insert the two lower screws leaving the head protruding approx. 5mm
20cm
MIN
0
HOLE
19cm
9.5cm
2.3cm
5
WALL
SCREW
1.8m
MAX
20cm
MIN
20cm
MIN
0
2.3cm
5mm
SCREW
WALL WALL
S
FLOOR
WALL
2
3
Arezzo - DF20LL 9/10/14 14:13 Page 5

6
4Hang the heater via the two lugs on the back of the heater.
5Using the supplied bracket, insert the final screw and tighten fully.
This will hold the unit in place and would require removing before
the heater can be taken down from the wall.
HOLE
1
mm
LL WALL
SCREW
FLOOR
W
0
HOLE
19cm
9.5cm
2 cm
5
SCREW
4
5
Arezzo - DF20LL 9/10/14 14:13 Page 6

4. ELECTRICAL CONNECTION
THE PRODUCT SHOULD ONLY BE CONNECTED TO A SUPPLY THAT
MEETS THE SPECIFICATIONS DETAILED ON THE RATING LABEL.
CONNECTION TO THE FIXED WIRING OF THE PROPERTY SHOULD BE
MADE BY MEANS OF A DOUBLE POLED SWITCH RATED FOR 13AMPS.
DO NOT USE THE HEATER IN CONJUNCTION WITH ANY AUTOMATIC
SWITCHING DEVICE SUCH AS A TIMER.AN OVERHEAT RISK EXISTS
IF UNATTENDED.
Electrical connections should be made as follows:
Brown/Red live wire to the terminal marked “L”
Blue/Black neutral wire to the terminal marked “N”
7
Arezzo - DF20LL 9/10/14 14:13 Page 7

5. OPERATION
DO NOT COVER HEATER
DO NOT PLACE ANY COMBUSTIBLE MATERIALS SUCH AS FURNITURE,
CURTAINS AND BEDDING WITHIN 1 METER OF THE HEATER.
THE UNIT IS INTENDED AS A ROOM HEATER AND SHOULD NOT BE
USED FOR ANY OTHER PURPOSE.
The heater has 4 settings that can be selected using upper power selection knob .
0 = Off
• = Cooling (fan only)
•• = 1kW (half power)
••• = 2kW (full power)
The heater has a power indictor light to show when it is operating .
Turn the thermostat knob fully clockwise to select the maximum setting, once the
desired room temperature is achieved turn the thermostat knob anti-clockwise until
a click is heard and the power indicator light goes off.The heater will now maintain
this temperature until the thermostat knob is adjusted again.
8
0
12
3
1
2
3
Arezzo - DF20LL 9/10/14 14:13 Page 8

6. CLEANING & MAINTENANCE
The heater should be examined for signs of physical damage at regular intervals, if any
signs of damage or overheating are present on either the heater or the power cord;
discontinue use of the heater immediately and contact an electrician or the Hyco
technical line for further advice.
To clean the product, first isolate the heater from the mains power supply and then
wipe the exterior with a clean damp cloth. Allow the heater to dry before turning
the mains power back on. To clear debris from the hot air outlet gently remove with
avacuum cleaner or soft brush.
9
Arezzo - DF20LL 9/10/14 14:13 Page 9

7. TROUBLE SHOOTING
Symptom Probable cause and solution
The heater will not turn Room warmer than the Turn up the thermostat.
on i.e. the power light thermostat setting.
will not illuminate.
Mains supply issue. Check mains supply
present and ensure the
fuse has not blown.
The unit has failed. Discontinue use and
isolate the mains
power supply before
contacting an
electrician or the
Hyco technical line.
The heater is blowing The auto-reset has Switch off the power
cold air. operateddue to over supply to the unit
heating. and allow to cool
before inspecting for
heat damage and any
cause of an abnormal
overheat before
turning the power
supply back on to
reset the cut-out.
The thermal fuse Discontinue use and
has operated due isolate the mains power
to over heating. supply before contacting
an electrician or the
Hyco technical line.
10
Arezzo - DF20LL 9/10/14 14:13 Page 10

11
8.TECHNICAL DATA
Arezzo - DF20LL
Voltage/Frequency 230V~ 50Hz
Power 1.0/2.0kW (selectable)
Dimensions h x w x d 245 x 240 x130 (mm)
Overheat protection type Self-hold cut-out 850C
(Dual devices) Thermal fuse 990C
Ingress protection IP23
Weight 1.6kg
9. GUARANTEE AND SERVICE POLICY
This product is guaranteed against faulty materials and manufacture for a period of
one year from the date of purchase. Hyco will in its sole discretion replace, repair
or refund any faulty unit. Defects arising from incorrect installation are excluded.
Consequential costs such as labour charges or damage to fittings and surroundings
are expressly excluded.
Arezzo - DF20LL 9/10/14 14:13 Page 11

INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN
ACCORDANCE WITH THE EUROPEAN DIRECTIVE 2002/96/E.
At the end of its working life this equipment must not be disposed of as
household waste. It must be taken to a local authority waste collection centre
or to a dealer providing this service. Disposing of electrical and electronic
equipment separately enables its components to be recovered and recycled to
obtain significant savings in energy and resources. In order to underline the
duty to dispose of this equipment separately, the product is marked with a
crossed out dustbin.
Hyco Manufacturing Ltd
Normandy Court, Express Way
Castleford,WF10 5NR
Sales: 01924 225 200
Fax: [phone]
Switchboard: 01924 225 215
Email: [e-mail]
www.hyco.co.uk
WATER HEATING SPACE HEATING HAND DRYERS
Arezzo - DF20LL 9/10/14 14:13 Page 12