Hyco FW400H User manual

Mojave
Frost Protector
Model FW400H
Instruction Manual
Version 1.0 May 2011

HYCO MOJAVE FROST PROTECTOR
MODEL FW400H
1. INTRODUCTION
Thank you for purchasing the Mojave Frost Protector. The FW400H is a wall
mounted, compact, electric convector heater used for frost protection and to heat
up small areas indoors.
Please read and understand these instructions BEFORE rst use.
2. IMPORTANT SAFETY POINTS
DO NOT COVER THE OUTLET AS IT MIGHT CAUSE
OVERHEATING.
ALWAYS KEEP THE OUTLET AND INLET GRILLS CLEAN.

UNPLUG THE UNIT BEFORE CLEANING. CLEAN THE OUTER
PART OF THE UNIT WITH A SOFT, DAMP CLOTH. NEVER USE
ABRASIVES OR SOLVENTS.
NEVER TOUCH THE UNIT WITH WET HANDS.

WHEN THE UNIT IS FIRST SWITCHED ON AFTER A LONG
PERIOD UNUSED, A BURNING SMELL MAY OCCUR DUE TO
DUST GATHERED ON THE ELEMENT.
THE UNIT SHOULD BE MOUNTED INDOORS IN A CLEAN
AND DRYENVIRONMENT.
ENSURE THE UNIT IS OUT OF REACH OF CHILDREN.

DO NOT INSTALL THE HEATER CLOSE TO ANY FLAMMABLE
MATERIALS.
ALWAYS DISCONNECT POWER SUPPLY WHEN NOT IN USE AS
EVEN WITH THE LOWEST THERMOSTAT SETTING, THE UNIT IS
STILL ON.
DO NOT INSTALL IN FRONT OF OR BELOW ANY POWER
OUTLETS OR SWITCHED SOCKETS.
THE UNIT COMES PRE-WIRED WITH A BS1363 UK PLUG.
ALWAYS FIT THIS UNIT WITH A 3 AMP FUSE.
1

2
2. IMPORTANT SAFETY POINTS (Continued)
THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS
(INCLUDING CHILDREN) WITH REDUCED PHUSICAL,
SENSORY OR MENTAL CAPABILITIES OR LACK OF
EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN
GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE
OF THE APPLIANCE BY A PERSON RESPONSIBLE FOR THEIR
SAFETY.
3. INSTALLATION –WALL MOUNTING ONLY
The unit must be installed to allow air to ow freely.
Please see below mounting guide for installation and be
aware of the minimum distances that must be kept.
4. OPERATION
1. Turn the Thermsotat Control knob (5) clockwise
as far as possible (Figure 3).
2. When the room is heater to a suitable
temperature, turn the control knob (5) anti-
clockwise slowly until the indicator lamp (4) goes
out.
3. The thermostat is
now set at the correct
temperature and will
automatically switch on and off to maintain this
setting.
1. Mounting bracket
2. Bracket screws
3. Hot air outlet
4. Neon indicator
5. Thermostat control
knob
6. Air Intake
6
1
2
3
4
5
Figure 1
Figure 3
Figure 2
30 cm
Minimum
100 cm
Minimum
40 cm
Minimum

4. OPERATION (Continued)
FROST PROTECTION SETTING (Figure 4)
When the thermsostat is set to the frost protection
setting, the heating element will automatically switch
on at approx. +5°C in order to protect against frost.
5. CARE AND MAINTENANCE
Cleaning
• Ensure unit is disconnected from the power supply and left to cool
before cleaning.
• Clean with a damp cloth and mild non-abrasive detergent.
• Do not allow water to reach any internal parts.
6. TECHNICAL SPECIFICATIONS
7. GUARANTEE AND SERVICE POLICY
This product is guaranteed against faulty materials and manufacture for a period
of one year from the date of purchase. Hyco will in its sole discretion replace,
repair or refund any faulty unit. Incorrect installation and failure to follow correct
operating instructions are excluded. Consequential costs such as labour charges
or damage to surroundings are expressly excluded.
Hyco Manufacturing Ltd
California Drive
Whitwood
Castleford
West Yorkshire
WF10 5QH
Tel: [phone] Fax: [phone]
Web: www.hyco.co.uk
E-mail: [e-mail]
3
MODEL FW400H
DIMENSIONS [mm] (H x W x D) 250 x 265 x 100
MAXIMUM POWER 400 - 450W
VOLTAGE 240V ~ 50Hz
Figure 4