Hyco Sun Prince SP1000HLG User manual

Product Instruction Manual
Sun Prince
1.0kW, 1.5kW, 2.0kW, 3.0kW, 4.0kW and 4.5Kw
Indoor Halogen Infrared Heater
Version 3.2 Jan 2015
V15.10/2

2
Thank you for purchasing the Hyco Sun Prince Heater. This heater is
ideal for heating applications in draughty or tall buildings such as garages,
warehouses, factories and si ilar difficult to heat situations where convection
heating would be i practical. Please read and understand these instructions
before co encing installation and leave the with the user when
installation is co plete.
1. Important safety points
•The Electrical installation must be carried out by a qualified electrician in accordance
with the current edition of the I.E.E. Wiring Regulations.
•This appliance must be earthed.
•nly connect the unit to a single phase supply with a mains voltage as specified on
the rating plate.
•Means for disconnection must be incorporated into the fixed wiring in accordance
with the wiring rules.
•The heater must be positioned at a minimum height of 1.8m.
•This heater is not equipped with a device to control the room temperature.
Do not use this heater in small rooms when they are occupied by persons not
capable of leaving the room on their own, unless constant supervision is provided.
•Children aged from 3 years and less than 8 years shall only switch on/off the
appliance provided that is has been placed or installed in its intended normal
operating position and they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children
aged from 3 years and less than 8 years shall not plug in, regulate and clean the
appliance or perform user maintenance.
•Some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present.
•The heater is not suitable for outdoor use or use in damp conditions.
•The heater is not suitable for use in locations where moving objects may collide

3
with the heater, for example in sports halls where balls may collide with the lamp.
•FIRE RISK - take particular care when positioning the heater near moveable
items such as curtains or doors. Make sure that a 1.8m clearance is achieved with
the moveable item in its closest position.
•Do not use the heater without the safety guard fitted or if the safety guard is
damaged.
•Do not use in ambient temperatures exceeding 25°C.
2. Installation
When choosing the location for mounting the Sun Prince, ensure that you have fol-
lowed the safety points and recommendations. All models can be mounted on the wall
bracket provided. Units SP3000H, SP4000HLG and SP4500H can also be ceiling mounted
using chains and eye bolts (not supplied).
The heater must be mounted with the lamps in the horizontal position to
avoid premature failure of the lamp.
The heater should be mounted following the minimum clearances as shown
in the mounting guide.
The heater can be ceiling mounted but the minimum angle of 20° to the
horizontal must be maintained.
The bracket supplied is designed to ensure the correct mounting angle is
maintained. Do not attempt to modify the bracket in any way as incorrect
mounting may cause the unit to overheat.
1.8m

Fig 1 – Assembly drawing
4

5
Wall mountin
Fig 2 Wall bracket mount to main body of the heater.
•When mounting the Sun Prince using the wall bracket provided, the minimum
distances and angle must be observed.
Model Number Distance A Distance B Angle C (°)
To wall (mm) To ceiling (mm)
SP1000HLG 700 500 20 - 90
SP1500HL 700 500
SP2000HLG 700 500
SP3000HL 700 500
SP4000HLG 700 500
SP4500HL 700 500
SP1000H
SP1500H
SP2000H
SP3000H
SP4000H
SP4500H

nce the position of the Sun Prince has been decided, the unit can be mounted.
•The “L” piece of the bracket should be firmly fixed in position using screws and
wall plugs.
•Attach the main body holder part of the bracket to the piece attached to the
wall using the nut and bolt provided.
•Position the Sun Prince mounting bolts that protrude from each side of the
unit through the holes in the bracket.
•Place the washers on the threads and tighten the cap nuts with the Sun Prince
at the desired orientation.
Ceilin mountin
Single units (SP1000HLG, SP1500HL, SP2000HLG) are not suitable for
ceiling ounting. Use only the wall bracket provided.
When ceiling ounting the unit, the ini u distances below ust be observed.
6
B
C
B

Model Distance A Distance B Distance C Angle D Chain Rating
Number To wall (mm) To wall (mm) To ceiling (mm) (Min - Max °) (kg)
SP3000HL 500 700 500 20 - 45 25
SSP4000HLG 500 700 500 20 - 45 25
SSP4500HL 500 700 500 20 - 45 40
When mounting the unit ensure the mounting surface is capable of
safely holding the weight of the unit being fitted.
The chains and eye bolts used to mount the unit must be rated to
the values shown.
7
C
D
A
B

Electrical
•The Electrical installation must be carried out by a qualified electrician in
accordance with the current edition of the I.E.E. Wiring Regulations.
•This appliance must be earthed.
•The electrical connection should be made to the fixed wiring of the property
using the appropriately rated cable (the supply cable must have a minimum
temperature rating of 90°C) and a double pole isolator switch should be used.
•Please note that an inrush current of several times the steady state current will
flow for a few hundredths of a second after first switching on, therefore a slow
blow circuit breaker should be used.
•PIR devices or other controllers may be used to control this unit provided
all devices are rated to the appropriate electrical loading with due allowance
for the in-rush current. (Hyco Quartz controllers are available and are fitted
with a “soft start” feature that negates the need for a slow blow circuit
breaker).
Cable fittin
•Remove the back box to gain access to the terminal block.
•Fit the cable gland into the back box.
•Feed the cable through the cable gland and secure in the correct position.
•Connect the cable to the terminal block ensuring the wires are in the
correct terminals:
Brown: L
Blue: N
Green / Yellow: E
•Ensure the connections are tight and there are no loose or frayed wires.
•Refit the back box.
Do not attempt to touch or adjust the heater until it has cooled down and
has been isolated from the power supply
8

3. Operation
This unit does not have an on/off switch and will operate as soon as ains power is
supplied to the unit.
4. Maintenance
•Before cleaning, ensure the heater is disconnected from the power supply and
has cooled completely.
•Wipe the exterior of the heater with a damp cloth.
•Do not use abrasives or chemical cleaners to clean the heater.
•If the reflector requires cleaning, use a soft, dry cloth taking care not to touch the
quartz lamp with bare hands.
Lamp replacement
•Check it is the correct lamp against the specification.
•Do not touch the lamp with bare hands. Always use a soft cloth.
•Do not touch the unit until it has been disconnected from the power supply and
has cooled completely.
•Remove the four screws holding the lamp guard in place.
•Remove the guard from the main body.
•Remove the reflector.
•Remove the back box covering the terminal block. Disconnect the lamp wires
from the terminal block that connects to the Live (L) and Neutral (N) terminals.
•Remove the lamp from the reflector, pulling the wires carefully through and dispose
of safely.
•Take the new lamp and feed the wires through the holes in the reflector.
•Connect the lamp wires to the terminals marked L and N.
9

•Clip the lamp into the lamp holders.
•Replace the reflector and secure the front guard using the four retaining screws.
•Replace the back box covering the terminal block.
5. Specifications
Model Power (kW) Lamp Colour* Lamp Qty x W
SP1000HLG 1.0 Gold 1 x L1000CGL
SP1500HL 1.5 Ruby 1 x L1500CL
SP2000HLG 2.0 Gold 1 x L2000CGL
SP3000HL 3.0 Ruby 2 x L1500CL
SSP4000HLG 4.0 Gold 2 x L2000CGL
SSP4500HL 4.5 Ruby 3 x L1500CL
Dimensions
Model Height (mm) Width (mm) Depth (mm) Weight (kg)
SP1000HLG 198 474 141 3.09
SP1500HL 198 474 141 3.09
SP2000HLG 198 474 141 3.09
SSP3000HL 398 474 141 5.35
SSP4000HLG 398 474 141 5.35
SSP4500HL 598 474 141 7.57
10

6. Guarantee and service policy
This product is guaranteed against faulty materials and manufacture for a period of one
year from the date of purchase. Hyco will in its sole discretion replace, repair or refund
any faulty unit (excluding lamps). Incorrect installation and failure to follow correct
operating instructions are excluded. Consequential costs such as labour charges or
damage to surroundings are expressly excluded.
H
WD
11

hyco.co.uk
Hyco Manufacturing Ltd
Normandy Court
Express Way
Castleford, WF10 5NR
T 01924 225 200
F 01924 225 210
E [email protected]
INF RMATI N F R C RRECT DISP SAL F THE PR DUCT IN ACC RDANCE WITH THE
EUR PEAN DIRECTIVE 2002/96/E.
At the end of its working life this equipment must not be disposed of as household
waste. It must be taken to a local authority waste collection centre or to a dealer
providing this service. Disposing of electrical and electronic equipment separately
enables its components to be recovered and recycled to obtain significant savings in
energy and resources. In order to underline the duty to dispose of this equipment
separately, the product is marked with a crossed out dustbin.
*2724*