Hyco Sun King Quartz User manual

Product Instruction Manual
Sun King Quartz
Outdoor Halogen Infrared Heater
SK1500
v20.7.3

Overview
Thank you for purchasing a Sun King Quartz Outdoor Halogen Infrared Heater. The Sun
King Quartz is ideal for heating outdoor domestic and commercial applications, such as
patios, beer gardens and smoking areas.
Key Features
• Allows heating of targeted areas
• Quartz halogen lamps operate at a very high temperature, converting almost all the
electrical energy into short wavelength infrared radiation
• Stylish, lightweight aluminium construction
• Silent operation
• Lamps made from high temperature resistant quartz glass lasting an average of 7000
hours
• Low glare gold lamps
• Weatherproof for outdoor use
The product should only be connected to a supply that meets the specications
detailed on the rating label.
Do not install the appliance if there is any sign of damage, especially to the power
cable or grille.
Do not locate the heater immediately below a socket.
The body of the heater can get very hot during usage, ensure the power cable
cannot contact with it following installation.
Do not use this heater with a programmer, timer, separate remote-control system
or any other device that switches the heater on automatically, since a re risk exists
if the heater is covered or positioned incorrectly.
1. Important Safety Points
Please fully read these instructions before commencing installation and follow to ensure
that installation and operation are simple and safe.
2

Ensure that any combustible materials such as curtains, paper, clothing, furniture
etc. are kept away at a minimum distance of 1.8m from all surfaces of the heater.
Do not install the heater in explosive or combustible environments.
The grille of this heater is intended to prevent direct access to heating elements
and must be in place when the heater is in use.
The appliance is not intended for use by any persons (including children) with
reduced physical, sensory, or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
the safe use of the appliance by a person responsible for their safety.
Children should be supervised to ensure they do not play with the appliance.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/o the
appliance provided that it has been placed or installed in its intended normal
operating position and they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children
aged from 3 years and less than 8 years shall not plug in, regulate and clean the
appliance or perform user maintenance.
Do not insert ngers or any other objects through the grilles of the appliance.
CAUTION — Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are
present.
3

Ensure the minimum distances are followed.
1. Installation
4
• Select a suitable surface that will support the product and accept the wall plugs
safely.
• When selecting the heater location, ensure the following minimum distances are
maintained: Floor 1.8 m, Wall 0.5 m, Ceiling 0.3 m (see diagram 1).
• Using the mounting holes on the heater bracket and ensuring a horizontal level, mark
four holes onto the mounting surface. Using the xings provided to attach the heater
securely to the wall.
• The angle of the heater should be adjusted by loosening the hinged part of the
bracket, selecting the angle and then tightening the hinge once again. Ensure the
angle is a minimum of 30 from vertical and no greater than 90 (See diagram 2).
Diagram 1 Diagram 2

5
2. Electrical Connection
• The steady state current of the heater is 6.5 A but an initial inrush current of many
times this value will occur when turned on from cold, for this reason a MCB type 3 is
recommended to avoid false tripping.
• The heater is supplied with 1.8 m of heat resistant cable and a 13 amp BS plug. When
the heater is connected outside, a weather proof socket is strongly recommended.
• If the heater is connected to the xed wiring of a property, connection should be
made as follows; -
Green/Yellow earth wire to terminal marked “E”or
Brown/Red live wire to the terminal marked “L”
Blue neutral wire to the terminal marked “N”
This appliance must only be connected to a power supply that corresponds to the
rating label specications.
If the appliance is connected to the xed wiring of the property, the electrical
installation should be carried out in accordance with the latest IET wiring
regulations.
Do not use the appliance with an extension cable.

3. Cleaning and Maintenance
When replacing the lamp, the unit should be safely disconnected from the
electrical supply and removed from the wall so it can be performed on a safe at
surface. Always ensure the heater has fully cooled before handling it.
Never handle the glass part of the lamp with bare hands, ngerprints will cause
the lamp to burn at this point and seriously impair the lifespan. To remove marks,
use a soft cloth and methylated spirits or alcohol.
• With the unit on a safe at surface, proceed to remove the hinged bracket 1. and
wiring box 2. from the main body of the unit 3.
6

• Remove both side panels from the unit 1. and slide both back panels away and out
from the main chassis 2.
7

• Remove the live and neutral lamp connections from the terminal block located inside
the wiring box.
• Remove the front guard by gently sliding out from either end of the heater 1.
• Remove the lamp from the heater by lifting it out of its holders and clear of the heater.
Feed the lamp cables out of the holes to complete the lamp removal 1.
• Take the new lamp and reverse all the steps to replace. If you experience diculty
please consult a professional, or contact Hyco.
8

4. Specication
Supply 230V ~ 50Hz
Power 1.5 kW
Current 6.5 A
Weight 1.4 kg
Ingress Protection 55
Dimensions 455W x 100H x 130Dmm
9

5. Guarantee
This product is covered by a standard parts or replacement warranty for a period of 1
year from the date of purchase.
If there is a manufacturing defect within the warranty period we will send spare parts,
repair and return the unit or, at our discretion, supply a replacement product (excluding
lamps). Incorrect installation or failure to follow correct operating and maintenance
instructions are excluded. Consequential costs such as labour charges or damage to
ttings and surroundings are expressly excluded.
6. Contact Us
If you experience a problem with this product you should rst contact our service
department on 01924 225 200 before taking any further action. Experience has shown
that issues can often be resolved without the need to return or uninstall the product.
Hyco Manufacturing Ltd
Normandy Court
Express Way
Castleford, WF10 5NR T 01924 225 200
F 01924 225 210
E [e-mail]
hyco.co.uk
INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE
WITH THE EUROPEAN DIRECTIVE 2012/19/EU.
At the end of its working life this equipment must not be disposed of as household
waste. It must be taken to a local authority waste collection centre or to a dealer
providing this service. Disposing of electrical and electronic equipment separately
enables its components to be recovered and recycled to obtain signicant savings
in energy and resources. In order to underline the duty to dispose of this equipment
separately, the product is marked with a crossed out dustbin.
10