HYOSUNG MoniMax7600 User manual

MoniMax7600 (Rear Load)
Installation Manual
Copyrightⓒ2010 Nautilus Hyosung Inc. All right reserved

MoniMax7600 Installation Manual
2
Table of Contents
Warning Signs
Common precautions for safety ····················································································· 3
Description of Warning signs ························································································· 4
Packing Dimensions
On-Site Packing Dimensions ···························································································· 5
Installation Information
Installation Condition and Space ···················································································· 6
Tools required for installation ························································································· 6
System Installation
Unpacking the System ···································································································· 7
Adjusting the System Height ·························································································· 9
Clearance Information
Terminal Dimensions ····································································································· 11
Installation and Service Clearances ············································································· 13
Precautions ······················································································································ 15

MoniMax7600 Installation Manual
3
Warning Signs
Common precautions for safety
Noncompliance with safety precautions mentioned in this manual can
result in bodily injury and/or product damage. This warning symbol is
used along with appropriate warning messages.
And it is also used to denote that the written text is related to safety.
Be sure to read and understand the following safety precautions before handling the product.
1. Follow the procedures shown in this manual.
2. Please comply with the safety precautions in this manual and on the product.
If you do not follow these precautions, bodily injury could result.
3. Do not attempt to operate the product in ways other than mentioned in this manual.
4. If a problem persists even after following the procedures laid out in this manual, please contact
our customer service department.
5. This equipment shall not be set up to make automatic calls to the telecom ‘111’ emergency service.
6. This equipment is not intended to be connected to a line in parallel with other terminal equipment.
7. This equipment should not be used under any circumstances which may constitute a nuisance to
other telecom customers.

MoniMax7600 Installation Manual
4
Description of Warning Signs
Sign Description
Risk Of Electric Shock
• Do not remove cover. Only a maintenance engineer should open the cover.
• To avoid risk of electric shock, do not touch.
• Make sure to turn off the power before servicing the equipment.
Hot Surface
• Do not touch the equipment when it is on.
• The equipment can get extremely hot and may cause a burn.
• Make sure to close the cover before running the equipment.
Moving
• The equipment is heavy. Make sure at least 2 people lift or move the equipment
• Do not attempt to move the equipment alone. You may be injured from
dropping the heavy equipment
Risk of Injury
• Always lock Push-Plate before adding cash to cassette.
• Refer to user manual for details.
Risk of Injury
• Turn off the machine before performing any service work.
• Use caution to avoid injury
Handling Heavy Equipment
• You may be injured if machine is dropped or mishandled.
• Use caution when moving the machine to avoid injury
Risk of Injury
• Use caution when operating the push-plate to avoid injury.
• The covers should be locked to avoid injury.
• Refer to operating manual before installing the cassette.

MoniMax7600 Installation Manual
5
Packing Dimensions
On-Site Packaging Dimensions
The design of packing used on below picture is structured for shipping of MX7600 by load or air/sea
freight. The dimension of the out box is ‘H 1780mm / W925mm / D1335mm’.
Fig.1

MoniMax7600 Installation Manual
6
Installation Information
Installation condition and space
Following conditions should be met before installing equipment.
●Temperature should be between 41~104°F (operating), 14~140°F (storage).
●Relative humidity should be between 25~85% (operating) / 10~90% (storage)
●Avoid locations where intense direct light is reflected off the LCD screen.
●Avoid locations where strong static electricity can occur.
●The floor must allow easy wheelchair access from the front or the side.
●Space required for servicing the machine should be considered before installation.
Tools required for installation
In order to move the machine and place it in a proper location, you need to get help of professionals
trained in moving heavy equipment.
Following tools are needed to install the machine.
Wire cutter
Lifter
Screw driver (Flat, Phillips)
Wrench (Spanner)
Leveling tool
Silicone
Silicone gun

MoniMax7600 Installation Manual
7
System Installation
Unpacking the System
Unpack the machine on top of the palette.
●Cut the straps that are fastened around the box with a knife. (refer to Fig.2)
(Be careful when cutting the straps.)
●Use an appropriate tool to remove the nails from the palette. (refer to Fig.3)
●Remove the lid, then box from the top. Do not discard the packaging materials until you have verified
any shipping damage claim. Contact your distributor immediately if you see any shipping damage.
Store the box in a safe place to re-use or discard of appropriately.
●Verify the contents carefully with the packing list to be sure all items listed are included. Notify your
distributor of any shortages.
●If only the palette needs to be removed, lift the whole machine from the bottom and set it aside.
Fig.2 Fig.3

MoniMax7600 Installation Manual
8
Fig.4

MoniMax7600 Installation Manual
9
Adjusting the System Height
System heights can be adjusted by adjustor bolt
●Lower the height as much as possible while making it as level as possible.
●.Adjust the height of the adjustor while keeping the distance from the bottom of the safe between
98~113 mm [3.86 ~ 4.45 inch].
●Adjust the position of the machine so that the door can be opened and closed easily.
●Use leveling tools to check if the machine is level.
Bottom of the safe
[3.86]
[4.36]
[5.90]
[4.45]
[0.79]
[0.59]

MoniMax7600 Installation Manual
10
BNA Caster can be adjusted in proportion to the height of the adjustor.
●Unfasten 4 bolts marked in below picture and adjust the BNA caster. (Distance of the holes is 3mm
[0.12])
●Adjust the BNA caster in proportion to the height of the adjustor and it should be lower by 3~5mm
[0.12 ~ 0.20] than the height of the adjuster.
Adjuster Hole
The distance of adjuste
r
holes is 3mm [0.12].