HYOSUNG MONiMAX8100T User manual

Operator Manual
MONiMAX8100T System
V01.00.00 (2018.11.7)
© Hyosung TNS Inc. All Rights Reserved.

© Hyosung TNS Inc. All Rights Reserved. I
Revision History
Operator Manual - MX8100T System
No.
Version
Date
Description of Change
Chapter
1
V01.00.00
2018/11/07
Preliminary version
All
© Hyosung TNS Inc. All Rights Reserved.
The content of this specification is protected by copyright laws.
2018. 11. 7 1st Release

II © Hyosung TNS Inc. All Rights Reserved.
Contents
Chapter1. Preface ..............................................................................................................................................1-1
Purpose ........................................................................................................................................................1-1
Audience.......................................................................................................................................................1-1
Support Information......................................................................................................................................1-1
What is in This Manual.................................................................................................................................1-1
Terminologies ...............................................................................................................................................1-2
Abbreviations................................................................................................................................................1-2
Safety Precautions (English)........................................................................................................................1-4
Précautions pour la sécurité (French) ..........................................................................................................1-6
Related Document ........................................................................................................................................1-9
Chapter2. Introduction ......................................................................................................................................2-1
About the MX8100T......................................................................................................................................2-1
The Exterior Overview..................................................................................................................................2-2
Basic Features..............................................................................................................................................2-3
Devices of MX8100T....................................................................................................................................2-7
Control Electronics (CE, PC)·······························································································2-7
Customer Display & PIN-Pad······························································································2-8
Teller Display···················································································································2-9
Bill Recycler (BRM58, Bill Recycle Machine) ········································································ 2-10
Check Single Deposit Module (CSM33, Check Scan Module 33) ·············································· 2-12
Card Reader ················································································································· 2-14
Contactless Card Reader (CCR)························································································ 2-15
Receipt Printer (SPR60)··································································································· 2-16
Barcode ······················································································································· 2-17
Chapter3. For the beginning operator.............................................................................................................3-1
Switching Power On/Off ...............................................................................................................................3-1
Switching Power On··········································································································3-1
Switching Power Off··········································································································3-1
Power Supply Status·········································································································3-2
Security Locking Device –Cencon Lock......................................................................................................3-3
Chapter4. Receipt Printer (SPR60)...................................................................................................................4-1
Introduction...................................................................................................................................................4-1
Summary......................................................................................................................................................4-2
Paper Specification.......................................................................................................................................4-4
Structure and functions.................................................................................................................................4-7
Install and load the paper roll .....................................................................................................................4-10
Clear the jammed paper in the cutter.........................................................................................................4-12
Clear the jammed paper in the presenter...................................................................................................4-13
Troubleshooting and maintenance.............................................................................................................4-14
Errors and settlement······································································································ 4-14
Solution for common errors······························································································· 4-15
Self-test page ················································································································ 4-17
Chapter5. Bill Recycler (BRM58)......................................................................................................................5-1
Basic Specification........................................................................................................................................5-2
Specification & Function·····································································································5-2
External Appearance·········································································································5-3
Bill Conditions...............................................................................................................................................5-4
Acceptable condition·········································································································5-4
Unacceptable condition······································································································5-5
How to open and close the lower module (BMD).........................................................................................5-9
Opening Lower Module (BMD) ····························································································5-9
Closing Lower Module (BMD)···························································································· 5-10

© Hyosung TNS Inc. All Rights Reserved. III
How to replenish the Recycling Cassette (RC) with bills ........................................................................... 5-11
How to remove bills from Retract/Reject Cassette (RT/RJC) ....................................................................5-15
How to open and close the upper module (BMU) ......................................................................................5-18
Opening Upper Module (BMU)···························································································5-18
Closing Upper Module (BMU) ····························································································5-18
Opening the Customer Service Module (CSM) ······································································5-19
Closing the Customer Service Module ·················································································5-20
Opening the Temporary Stacker (TSK)·················································································5-21
Closing the Temporary Stacker (TSK) ··················································································5-22
How to remove the jam...............................................................................................................................5-23
Chapter6. Check Single Deposit Module (CSM33).........................................................................................6-1
Configuration & Specification of Device .......................................................................................................6-1
Device Configuration········································································································· 6-1
Device Specification·········································································································· 6-3
Check Conditions .........................................................................................................................................6-5
Switch Specification....................................................................................................................................6-10
How to open & close each Module............................................................................................................. 6-11
Main Module Opening······································································································6-11
Main Module Closing ·······································································································6-11
Printer Module Opening····································································································6-12
How to replace the Cartridge......................................................................................................................6-13
How to replace the Felt...............................................................................................................................6-14
How to remove the check from Stack Bin...................................................................................................6-16
How to remove Jam....................................................................................................................................6-17
Careful for the damage...............................................................................................................................6-18

Operator Manual Chapter1. Preface
© Hyosung TNS Inc. All Rights Reserved. 1-1
Chapter1. Preface
Purpose
►This manual is produced to describe how the customers operate Hyosung TNS
MX8100T.
This manual details how the customers replenish the notes and paper and how they
remove the jam at the MX8100T.
Audience
►Customers and staffs of Hyosung TNS who use and operate the MX8100T in each
branches of bank.
Support Information
►If any question or error occurs while operating MX8100T in compliance with this
manual, please contact maintenance staffs of Hyosung TNS.
For the contact of maintenance staffs of Hyosung TNS, see the E-mail addresses and
telephone numbers provided separately.
What is in This Manual
►MONiMAX referred to as “MX”
►This manual is designed to provide the operation guide for the MX8100T and the
detailed description of the following:
▪Replenishing the notes and the receipt paper
▪Emptying the notes
▪Removing the jam like the notes and the receipt paper
►All information described in this manual is a licensed product of Hyosung TNS.
Some of the information in this manual may differ according to the network processor
to be connected and may be subsequently updated by the bank’s needs or the
improvement by Hyosung TNS.
It is the policy of Hyosung TNS to improve products as new technology, components,
software, and firmware become available. Therefore Hyosung TNS reserves the right
to change specifications without notice.

Chapter1. Preface Operator Manual
1-2 © Hyosung TNS Inc. All Rights Reserved.
Other company names and product names described in this document are trademarks
or registered trademarks of each company. For the section of that product, the whole
section or a necessary part of relevant document is quoted.
Terminologies
►In this document the terminology listed below is used as follows:
▪Customer and consumer refer to any person who transacts business through the ATM.
▪Device and unit refer to the standard and option
al ATM equipment, such as monitor, card reader, printer and dispenser.
▪Fascia refers to the entire front portion of the unit, including the portion where the
customer transacts business.
▪Module refers to a plug-in device that can be serviced or replaced.
▪Note(s) and bill(s) refer to the individual documents loaded into and dispensed from
the dispenser.
▪Servicing and maintenance refer to the supervisor, operator and technician’s tasks
performed to keep the ATM operational.
▪Screen refers to the text appearing on the customer display.
Abbreviations
►In this document the abbreviations listed below is used as follows:
#
Abbreviations
Description
1
AD board
Analog Digital Board
2
ADA
The American Disabilities Act
3
AP
Application Program
4
Assy
Assembly
5
BRM
Bill Recycling Machine
5-1
BC
Bill Checker
5-2
BMD
Body Module-Down (Lower Body of the Machine)
5-3
BMU
Body Module-Up (Upper Body of the Machine)
5-4
CSM
Customer Service Module
5-5
DPC
Deposit Cassette
5-6
RC
Recycle Cassette
5-7
RJC
Reject Cassette
5-8
TSK
Temporary Stacker
5-9
UTC
Utility Cassette

Operator Manual Chapter1. Preface
© Hyosung TNS Inc. All Rights Reserved. 1-3
#
Abbreviations
Description
6
BATT S/W
Battery Switch
7
CAM
Camera Unit
8
CE
Control Electronics
9
Earphone Jack
Voice Converter for Visually Disabled Persons
(ADA)
10
EMV
Europay, Mastercard, Visa
11
EP
Elementary Program
12
EPP
Encryption PIN Pad
13
H/W
Hardware
14
I/F
Interface
15
ISO
International Standard Organization
16
JPR
Journal Printer
17
LCD
Liquid Crystal Display
18
MCU
Magnetic Card Unit
19
OPL
Operation Panel for Customers to Operate
20
OSD board
On Screen Display Board
21
P/S
Power Supply
22
PIN
Encryption PIN Pad
23
PNC
Panel Control Board
24
PTR
Printer (mainly Receipt Printer)
25
S/W
Switch
26
SIU
Sensor and Indications Unit
27
SP
Service Provider
28
SPR
Slip Printer (Receipt Printer)
29
TTU
Text Terminal Unit (OPL or SPL)

Chapter1. Preface Operator Manual
1-4 © Hyosung TNS Inc. All Rights Reserved.
Safety Precautions (English)
▶Common Safety Precaution
Precautions outlined this manual provide information on safe
and proper handling of the product. Non-compliance of the
precautions may result in injury or damage to the product.
This precaution symbol with sample term tells you safety
warnings during equipment handlings.
▶Please read the following instructions before operating equipment.
▪Operate equipment in the order outlined in this manual.
▪Follow precautions indicated in this manual, as well as the equipment itself.
Failure to properly address these precautions may lead to injury or damage to the
product.
▪Avoid operations not addressed in this manual.
▪If you cannot remedy system problems using the methods outlined in this manual,
please refer to contact information listed in the manual.
▪Any change or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
<Note!>
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
▶Description of Precaution Symbols
Symbol
Description
Electrical Shock Warning
▪Do not remove cover. Only a maintenance engineer is allowed
to open the cover.
▪Do not touch. You may receive electric shock.
▪Make sure to turn off the power when servicing the equipment.
High Temperature Warning
▪Do not touch the equipment when it is running.
▪The equipment can get extremely hot and may cause a burn.
▪Make sure to close the cover before running the equipment.

Operator Manual Chapter1. Preface
© Hyosung TNS Inc. All Rights Reserved. 1-5
Symbol
Description
Use Precaution when Moving
▪The equipment is heavy. Make sure at least 2 people lift or
move the equipment.
▪Do not attempt to move the equipment alone. You may be
injured from dropping the heavy equipment.
Fire Hazard
▪Place the equipment in an area away from any combustible
materials.
▪The equipment may catch on fire from overheating or short
circuit of the power supply unit.
Disassembly Warnings
▪Do not disassemble or modify the equipment unless you are a
certified engineer.
▪Contact the service center for maintenance, adjustments and
repairs.
▪Improper disassembly may cause fire or electrical shock.
Collapse Precautions
▪Do not place the equipment where the floor cannot sustain the
weight of the equipment, or on slanted or unstable surface.
▪Equipment may fall and cause injury or damage.
Unplug the Equipment
▪Stop using the equipment immediately if it smokes, emits an
unusual smell, makes abnormal sounds, or if liquids or other
foreign materials enter the equipment.
▪If the above-mentioned abnormalities occur, immediately turn off
the power, unplug the equipment and contact the service center.
▪If you ignore these symptoms, the equipment may catch on fire
or cause electric shock.
<CAUTION>
1. TO REDUCE THE RISK OF FIRE, USE ONLY No. 26 AWG OR LARGER
TELECOMMUNICATION LINE CORD
2. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSED OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
3. FOR PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED
NEAR THE EQUIPMENT AN SHALL BE EASILY ACCESSIBLE
4. THE EQUIPMENT IS TO BE SECURED TO THE BUILDING STRUCTURE
BEFORE OPERATION

Chapter1. Preface Operator Manual
1-6 © Hyosung TNS Inc. All Rights Reserved.
Précautions pour la sécurité (French)
►Précaution générale pour la sécurité
Précautions décrits de ce manuel fournissent des informations
sur une manipulation sûre et appropriée du produit. Le non-
respect des précautions peut causer des blessures ou
endommager le produit.
Ce symbole de précaution avec le terme d’example vous
indique des consignes de sécurité lors de la manipulation de
l'équipement.
►Veuillez lire des instructions suivantes avant d'utiliser l'équipement
▪Fonctionner l'équipement dans l'ordre indiqué dans ce manuel.
▪Suivre les précautions indiquées dans ce manuel, ainsi que l'équipement lui-même.
Le défaut de traiter correctement de ces précautions peut entraîner des blessures ou
endommager le produit.
▪Évitez des opérations non traitées dans ce manuel.
▪Si vous ne pouvez pas résoudre des problèmes du système en utilisant des méthodes
décrites dans ce manuel, veuillez se référer aux informations de contact figurant dans
le manuel, s’il vous plaît.
▪Certain changement ou des modifications dans la construction de ce dispositif qui ne
sont pas expressément approuvés par la partie responsable de la conformité
pourraient annuler l'autorité de l'utilisateur de faire fonctionner l'équipement.
<REMAQUE!>
Cet équipement a été testé et fondé pour se conformer aux limites pour un équipement
numérique de classe A, conformément à la partie 15 des règles FCC. Ces limites sont
conçues pour fournir une protection raisonnable contre des interférences nuisibles
lorsque l'équipement est utilisé dans un environnement commercial. Cet équipement
génère, utilise et peut émettre des fréquences radios et, s'il n'est pas installé et utilisé
conformément aux instructions de ce manuel, peut causer des interférences nuisibles
aux communications radios.
Le fonctionnement de cet équipement dans une zone résidentielle est susceptible de
provoquer des interférences nuisibles dans le cas, l'utilisateur devra corriger ces
interférences à ses propres frais.
►Description des symboles de précaution
Symbole
Description
Choc électrique
• Ne pas retirer le couvercle. Seul le technicien d'entretien est
autorisé à ouvrirle couvercle.
• Ne pas toucher. Vous pouvez avoir un choc électrique.
• Assurez-vous d'éteindre l'appareil lors de l'entretien de
l'équipement.

Operator Manual Chapter1. Preface
© Hyosung TNS Inc. All Rights Reserved. 1-7
Symbole
Description
À haute temperature
• Ne pas toucher l’équipement quand il est en marche.
• L’équipement peut devenir extrêmement chaud et peut
provoquer une brûlure.
• Assurez-vous de fermer le couvercle avant de lancer
l'équipement.
Soyez prudent lors du déplacement
• L'équipement est lourd. Assurez-vous d'au moins 2 personnes
pour soulever ou déplacer l'équipement
• N'essayez pas de déplacer l’équipement seul. Vous pouvez
être blessés par la chute de l'équipement lourd.
Risque d'incendie
• Placer l’équipement dans une zone éloignée de tous les
matériaux combustibles.
• L'équipement peut s'enflammer de surchauffe ou de court-
circuit de l'unité d'alimentation.
Démontage
• Ne pas démonter ou de modifier l'équipement, sauf si vous
êtes ingénieur certifié.
• Contacter le centre de service pour l'entretien, le réglage et
la réparation.
• Le mauvais démontage peut provoquer un incendie ou un
choc électrique.
Tomber
• Ne pas placer l'équipement dont le sol ne peut pas supporter
le poids de l'équipement, ou sur une surface inclinée ou
instable.
• L'équipement peut tomber et provoquer des blessures ou
des dommages.
Débrancher l'équipement
• Cessez d'utiliser l’équipement immédiatement si il fume, émet
une odeur inhabituelle, fait des bruits anormaux ou si des
liquides ou d'autres matériaux étrangers dans l'équipement.
• Si les anomalies mentionnées ci-dessus se produisent,
éteignez immédiatement la puissance, débranchez l'appareil
et contactez le centre de service.
• Si vous ignorez ces symptômes, l’équipement peut prendre
feu ou provoquer un choc électrique.
AVERTISSEMENT :
1. POUR RÉDUIRE LES RISQUES D'INCENDIE, UTILISEZ UNIQUEMENT AWG n °
26 OU LA LIGNES DE TELECOMMUNICATION PLUS GROSSE
2. RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLACEE PAR UN TYPE
INCORRECT. DISPOSER POUR UTILISATION DES BATTRIES SELON LES
INSTRUCTIONS
3. POUR LES APPAREILS RACCORDES, LA PRISE DOIT ETRE INSTALLEE PRES

Chapter1. Preface Operator Manual
1-8 © Hyosung TNS Inc. All Rights Reserved.
D’EQUIPEMENT POUR ÊTRE FACILEMENT ACCESSIBLE
4. L’EQUIPEMENT DOIT ETRE SECURISE A LA STRUCTURE DU BATIMENT AVANT
D'UTILISER

Operator Manual Chapter1. Preface
© Hyosung TNS Inc. All Rights Reserved. 1-9
Related Document
►The related documents are listed as follows. If needed, please contact staffs of our
technical support team and maintenance team.
▪Installation Manual
▪Service Manual
• Error Code Manual
For the contact of maintenance staffs of Hyosung TNS, see the E-mail addresses and
telephone numbers provided separately.

Operator Manual Chapter2. Introduction
© Hyosung TNS Inc. All Rights Reserved. 2-1
Chapter2. Introduction
About the MX8100T
►The MX8100T is a full service ATM. Cardholders and/or customers deposit and
withdraw the cash and receive the transaction records with MX8100T ATM
The MX8100T is a versatile, easily maintained delivery system that can be modified to
keep pace with the bank's changing needs.
►The benefits that the new concept MX8100T provides are as follows.
Removes inconvenience which occurs when bank clerks directly handle cash with
customers and relieves workload upon tellers by processing deposit/withdrawal of cash
automatically.
Relieves risks and burden of directly handling cash by directly keeping cash deposited in a
safe.
Allows tellers to calculate and close amount on hand faster than the existing manual
calculation.
Abank customer and a teller can easily interact on a touch screen, just like talking, through
Hyosung TNS’s intuitive and easy UI.
Allows easy and quick installation and maintenance.
<Note!>
The figures/photos/diagrams in this manual are for well understanding therefore they may
be different from real machines.

Chapter2. Introduction Operator Manual
2-2 © Hyosung TNS Inc. All Rights Reserved.
The Exterior Overview
►The following picture shows the front of MX8100T and key units.
The fascia provides the interface between the customer and MX8100T.
The customer selects transactions and requests information at the fascia.
Cash
(Bill Recycling
Machine)
Contactless
Card Reader
(CCR)
EPP (Pin-Pad)
Earphone Jack
Check Deposit
Receipt Printer
Slot
Card Reader
Slot
Customer
Display (with
touch screen)

Operator Manual Chapter2. Introduction
© Hyosung TNS Inc. All Rights Reserved. 2-3
Basic Features
►Important features of the MX8100T is highlighted in the following list:
<Note!>
Your MX8100T may not contain all the devices described in this section. Some devices are optional and
some devices cannot be used in combination with other devices (mutually exclusive combinations).
►System Specification
Item
Specification
Remarks
Main
Controller
(ASRock
IMB-184-
NH)
vPRO
Support
Main board form factor
Mini-ITX (6.7” x 6.7”)
CPU
Intel® Core™ i5-4590s
Processor
6M Cache, 3.0Ghz,
vPRO Support
BIOS
UEFI
Memory
DDR3L 4GB
SSD
128 GB
mSATATYPE
Operating System
Windows 7
Expansion Slots
Mini-PCIe 1slot, PCIe x 4
1slot
Serial Ports
4 Ports, Internal connector
USB Ports
USB 2.0
21 Ports
MAIN B/D 2 Ports,
Mini Hub1 4ports,
Mini Hub2 7ports,
Hub3/4 4ports
USB 3.0
2 Ports
USER PORTS
Graphics
On-board
On-Board Dual VGA(DVI,
HDMI)
Intel HD Graphics
Ethernet
10/100/1000Mbps On-Board
vPRO Support
Customer
Display
Display
Type
15” TFT LCD
Resolution
1,024 X RGB X 768
Brightness
350 cd/m²
Input Method
Touch Screen
15” Multi Touch Screen(P-
CAP)
Privacy Filter
15” (335 mm X 225 mm)
Viewing Angle 60°
Guide Light
Flicker
BRM, SPR, MCU, CSM,
BRM Shutter
Color : Blue
Color : White
Indicator
NFC
Color : Blue
Customer
Input
Method
Touch Screen
15” Multi Touch Screen(P-
CAP)
USB Interface
Pin-Pad
Polycarbonate EPP(PCI
Compliant)
EPP Guard Support
Supervisor
Operation
Display Module
10.4” TFT LCD, 250cd/m2
Input Method
10.4” Resistive Touch Screen
Mover
Type
Slide Drawer

Chapter2. Introduction Operator Manual
2-4 © Hyosung TNS Inc. All Rights Reserved.
Item
Specification
Remarks
Bill Recycler
(BRM58)
Interface Type
USB 1.1(Main), USB 2.0(BC)
BCU Type
BCU53
Sutter type
Automatic Shutter
Service CST
None
CST locking
Common key
Dispense/Deposit capacity
300 bills per Transaction
Dispense/Deposit method
Bundle
Functional Architecture
3 RC + 1RJC/RTC
Denomination
Cassette
Install Max
10,850 bills (when auto
stack)
When 0.1mm thick-bill
used
11,300 bills (Injection of
human)
Recycling
CST
2,850 bills (when auto stack)
3,000 bills (Injection of
human)
Reject CST
2,000 bills(when auto stack)
Retract CST
300 bills(when auto stack)
Dispensing Speed
10 notes/sec
Check
Single
Deposit
Module
(CSM33)
Interface Type
USB 1.1(Main), USB 2.0(BC)
Media Size
Width
Min : 60 mm ~ Max : 102 mm
Length
Min : 110 mm ~ Max : 230
mm
Thickness
Min : 0.075 mm to Max : 0.2
mm
Deposit
Type
Single
Capacity
Max. 1 checks/1 transaction
Direction
4 way
Box capacity
About 300 ea
When 0.203mm thick –
check used
Box type
Bin
Image
Capture
(Canon:
MG06H-
Z02)
Type
Reflection Two side &
Transmission
200 dpi
Reflection
Red, Green, Blue, IR940
Transmission
Green, IR730, IR880
Resolution
200dpi
Method
Digital I/F, Face up and Down
Endorsement
Type
Ink jet 1 Line

Operator Manual Chapter2. Introduction
© Hyosung TNS Inc. All Rights Reserved. 2-5
Item
Specification
Remarks
Print
(HP :
6602A)
Speed
31.25 ips
Endorsement
Resolution
96 dpi
Ancillary
function
Reject
Support
Canceled the
deal
Support
Maintenance
function
Batch test
Support
P/G down
load
Support
After the command start
Logging
Support
JPR
Journal Printer
Electronic Journal
Card
Reader
(ICM370-
3R2896)
Type
Dip Type(USB)
Vertical integrated
Magnetic Stripe
ISO 1,2,3 Read
IC card Support
Support
Anti-skimming
Jamming signal function
support
Anti-shimming
Metal plate type support
Contactless
Card
Reader
(IDTECH
KIOSK III)
Functional Branding
Octagon shape,
Blue flicker turns on/off slowly
Audio guidance
Beeper
Transaction Interface
ISO/IEC 14443 Type A and B,
ISO 18092,
ISO 21481 (PCD & NFC)
Payment Applications
American Express
ExpressPay 3.0,
Discover DPAS 1.0,
Interac Flash v1.5,
MasterCard PayPass/MChip
3.0.2,
Visa VCPS 2.1.3 - MSD,
qVSDC and IRWIN, Mifare,
Apple Pay & other Mobile
Wallets
Receipt
Printer
(SPR60)
Printing Type
Thermal Line Printing
Printing speed
100mm/sec
Printing Width
Max. 80mm
Paper Roll Capacity
5,000 Transaction/Roll
Depends on Format
Black Mark Paper Support
None
Option
Paper
Specification
Type
Thermal Roll Paper
Width
Max. 80mm
Outer
Diameter
Max. 210Φ
Barcode
(Honeywell)
Barcode Reader
Payable option
2D BCR (Honeywell 3330g)

Chapter2. Introduction Operator Manual
2-6 © Hyosung TNS Inc. All Rights Reserved.
Item
Specification
Remarks
Safety
&
Security
Safety
UL291 Level-1
(Rear, Front Access)
Locking device
Cencon Lock
Key Lock
Common Key
Alarm
Seismic & Heat Sensor
Security
Terminal Block (External I/F)
Camera
CCD Camera 1st(face), 2nd
(hand)
Camera I/F
Video Port /w Pig Tail for
internal Cam
Video Power /w Pig Tail for
Cam
Additional
function
Audio guidance
Sound Card On-Board
ADAAudio guidance
Volume Control Support
Dimension
&
Environment
Dimension (H X W X D)
66.5” X 24.8” X 39.7”(8.5”
Sleeve)
66.5” X 24.8” X 41.2”(10”
Sleeve)
66.5” X 24.8” X 44.2”(13”
Sleeve)
66.5” X 24.8” X 46.2”(15”
Sleeve)
Lobby : 53.5” X 20.5” X
34”
1,358.5 X 520 X 863.6
(mm)
Safety Door Open Direction
LEFT TO RIGHT SWING
(Front View)
Normal Swing
Install Method
Anchor
Weight
1,278 lbs (580kg)
Lobby : About 992 lbs
(450kg)
Battery
System Battery
Alarm Battery Option
Heater
None

Operator Manual Chapter2. Introduction
© Hyosung TNS Inc. All Rights Reserved. 2-7
Devices of MX8100T
Control Electronics (CE, PC)
►The Control Electronics mainly consist of a motherboard, HDD, multiple serial card, and so on.
Basic functions of the control electronics used in this ATM is similar to that of a personal
computer you may have in your office or home with exception of a multiple USB HUB used to
communicate with several devices such as a cash dispenser, card reader, receipt printer and
EPP.
►Basic Specification & Sample Picture